Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

Flow-injection analysis with fluorescence detection for the determination of trace levels of ammonium in seawater

A method using flow-injection, gas-diffusion, derivatisation and then fluorescent detection has been established for ammonium ion determination in seawater. The fluorescent derivative formed by reacting ortho-phthaldialdehyde (OPA) and sulfite with ammonia gives high sensitivity while removing potential interferences. This is required to measure the low concentrations of ammonium often seen in the open ocean. The experimental conditions (flow-rate, reagent concentrations, membrane configurations, etc.) were manipulated to improve performance. For a sample throughput of 30 samples h(-1), the limit of detection was 7 nM, the coefficient of variation was 5.7% at 800 nM, and the calibration curve was linear to at least 4 micromol L(-1). Interferences were minimised by a gaseous diffusion step. Volatile small molecular-weight amines as interferents were discriminated against by this method. They neither passed through the membrane as efficiently as ammonia, nor reacted as readily with OPA when sulfite was the reductant. Contamination by ammonia from laboratory and shipboard sources complicates application of the method to natural waters, especially measurement of low concentrations (<100 nM) in open-ocean waters. Steps to overcome contamination are described in detail. Some results are presented for ammonium determination in Southern Ocean and Huon Estuary (Tasmania) waters.     

Environmental benchmarks vs. ecological benchmarks for assessment and monitoring in Canada: Is there a difference?

Environmental benchmarks are widely used in Canadian environmental assessment as a standard against which to monitor air or water quality in response to human activities in the environment. Recent work in Canada has developed the concept of ecological benchmarks as a complement to environmental benchmarks. However, implementation of ecological benchmarks may be challenging. This paper presents an analogy between ecological benchmarks and the more commonly used environmental benchmarks, as an attempt to increase understanding and use of ecological benchmarks in resource management, assessment, and monitoring. Ecological benchmarks, and their corresponding indicators, will be challenging to identify and use. However, through the use of the principles of adaptive management, effective ecological indicators and benchmarks can be established. Although it is essential that ecological benchmarks are site-specific, the analogy and general principles outlined here are applicable to assessment and monitoring in any part of the world.     

210Po bioaccumulation in coastal sand dune wild legumes--Canavalia spp. of southwest coast of India

In view of considerable natural background radioactivity reported from southwest coast of India, the current study documents bioaccumulation of 210Po in two dominant coastal sand dune perennial mat-forming wild legumes, Canavalia cathartica and C. maritima. Root, stem, leaf, mature beans, dry seeds and rhizosphere sand were analyzed for 210Po concentration. 210Po activity decreased in the order of leaves > roots > seeds > stems > beans. The highest 210Po activity was recorded in rhizosphere sand samples (5.78-5.88 Bq kg(-1)) followed by the leaf samples (3.27-3.07 Bq kg(-1)), while it was lowest in mature beans (0.13-0.20 Bq kg(-1)). 210Po activities or tissue moisture between plant species were not significantly different (p > 0.05; t-test). But 210Po activity vs. moisture differed significantly in all tissues (p = 0.0001), vegetative tissues (root, stem and leaf) (p = 0.0016), seeds (p = 0.0393) and proteins in seeds (p = 2.355 x 10(-6)) indicating the importance of moisture and protein in 210Po accumulation. Although 210Po has affinity for proteins, it did not concentrate too much in seed proteins of Canavalia. Concentration of 210Po in mature beans is at safe levels as fisher folk only consume tender pods occasionally. 210Po activity in Canavalia is compared with other plant materials. As the landraces of C. cathartica and C. maritima are distributed throughout pantropical coastal areas, the current study emphasizes on considering them as bioindicators to monitor 210Po in coastal sand dune biomes and in turn the health of coastal population.     

The organic composition of diesel particulate matter, diesel fuel and engine oil of a non-road diesel generator

Diesel-powered equipment is known to emit significant quantities of fine particulate matter to the atmosphere. Numerous organic compounds can be adsorbed onto the surfaces of these inhalable particles, among which polycyclic aromatic hydrocarbons (PAHs) are considered potential occupational carcinogens. Guidelines have been established by various agencies regarding diesel emissions and various control technologies are under development. The purpose of this study is to identify, quantify and compare the organic compounds in diesel particulate matter (DPM) with the diesel fuel and engine oil used in a non-road diesel generator. Approximately 90 organic compounds were quantified (with molecular weight ranging from 120 to 350), which include alkanes, PAHs, alkylated PAHs, alkylbenzenes and alkanoic acids. The low sulfur diesel fuel contains 61% alkanes and 7.1% of PAHs. The identifiable portion of the engine oil contains mainly the alkanoic and benzoic acids. The composition of DPM suggests that they may be originated from unburned diesel fuel, engine oil evaporation and combustion generated products. Compared with diesel fuel, DPM contains fewer fractions of alkanes and more PAH compounds, with the shift toward higher molecular weight ones. The enrichment of compounds with higher molecular weight in DPM may be combustion related (pyrogenic).     

The study of age influence on human bone lead metabolism by using a simplified model and X-ray fluorescence data

Long term lead metabolism in the human body has never been fully understood due to the lack of human data in this area. The technological improvement of bone lead measurement systems has made bone lead data of substantial populations available. In this study, a set of X-ray fluorescence bone lead data was used to test Leggett's lead metabolism model (R. W. Leggett, Environ. Health Perspect., 1993a, 101, 598-616), especially the model of metabolism in bone. The data set includes the bone lead concentration of 539 occupationally exposed workers, of whom 327 were measured twice in five years. The bone lead concentrations of both cortical bone (tibia) and trabecular bone (calcaneus) were obtained by Cd-109 gamma-ray induced XRF measurement. The histories of blood lead concentration for these workers were used to regulate the input file of the model. The results show that the bone lead concentrations predicted by Leggett's model greatly underestimate the measured values, especially for older workers. This data set was then organized into five age groups. A new simplified model was applied to estimate the lead transfer rates between blood and lead compartments for these age groups. The original transfer rates and the new transfer rates are compared, and the differences are discussed. When the transfer rates derived from measured bone lead data were put into the input file of the model to replace the existing parameters, the predicted values were much closer to the measured values for both cortical bone and trabecular bone.     

Exposure and inhalation risk assessment in an aluminium cast-house

To date the exposure, absorption and respiratory health effects of cast-house workers have not been described since most studies performed in the aluminium industry are focused on exposure and health effects of potroom personnel. In the present study, we assessed the external exposure and the absorbed dose of metals in personnel from the aluminium cast house. This was combined with an evaluation of respiratory complaints and the lung function of the personnel. 30 workers from an aluminium casting plant participated and 17 individuals of the packaging and distribution departments were selected as controls. The exposure was assessed by the quantification of total inhalable fume with metal fraction and by the determination of urinary aluminium, chromium, beryllium, manganese and lead concentration. Carbon monoxide (CO), carbon dioxide (CO2), aldehydes and polyaromatic hydrocarbons and man-made mineral fibres concentration were assessed as well. In order to evaluate their respiratory status each participant filled out a questionnaire and their lung function was tested by forced spirometry. Total inhalable fume exposure was maximum 4.37 mg m(-3). Exposure to the combustion gases, man-made mineral fibres and metal fume was well below the exposure limits. Beryllium could not be detected in the urine. The values of aluminium, manganese and lead in the urine were all under the respective reference value. One individual had a urinary chromium excretion above the ACGIH defined biological exposure index (BEI) of 30 microg g(-1) creatinine. There was no significant difference in any of the categories of the respiratory questionnaire and in the results of the spirometry between cast house personnel and referents (Chi-square, all p > 0.05). Exposure in cast houses seem to be acceptable under these conditions. However, peak exposure to fumes cannot be excluded and the potential risk of chromium and beryllium exposure due to the recycling of aluminium requires further attention.     

A modular approach to Integrated Assessment modeling

In this paper, we present a new approach to model coupling that probably forms the methodological basis of a new generation of Integrated Assessment models. This approach respects the knowledge and expertise that is embodied in existing models and encourages their gradual evolution. Modularity is the guiding principle. Our approach is distinguished by the way modules are coupled which is based on an interplay of a job control module, a numerical coupling module, and a couple of stand-alone functional modules. The numerical coupling module - the core component - serves to treat the feedbacks between the functional modules. A first implemented example that couples an economic and a climate module by means of a two-phase meta-optimization is presented here. The algorithm and mathematical structure behind are discussed as well as important features such as convergence behavior and reliability.