钙钛矿型La_(0.8)Ce_(0.2)Fe_(1-x)Co_xO_3催化剂的制备及其三效催化活性

采用自燃烧法制备了一组钙钛矿型复合氧化物La_(0.8)Ce_(0.2)Fe_(1-x)Co_xO_3(x=0.9,0.7,0.5,0.3,0.1),并考察了其对CO、C_3H_6和NO的三效催化活性。XRD和SEM表征结果显示,La_(0.8)Ce_(0.2)Fe_(1-x)Co_xO_3具有良好的钙钛矿型晶体结构,晶粒大小为纳米级并自组装成片状结构。催化剂的比表面积为14.73~22.43 m~2/g,含有微孔和介孔结构。催化活性评价结果表明:La_(0.8)Ce_(0.2)Fe_(0.1)Co_(0.9)O_3具有很好的三效催化活性,在理论空燃比的条件下,CO、C_3H_6和NO的起燃温度分别为195℃、264℃和290℃,完全转化温度分别为239℃、418℃和415℃,低温三效催化活性良好;Fe和Co的掺杂量同时影响着La_(0.8)Ce_(0.2)Fe_(1-x)Co_xO_3的催化效果。     

废水中甲基橙的电化学降解

以FTO导电玻璃作为阳极、石墨电极作为阴极电解模拟甲基橙废水,优化了工艺条件,并对甲基橙的降解机理进行了初步探究。实验结果表明,在NaCl投加量5 g/L、电压8 V、废水pH 6、初始甲基橙质量浓度6.0 mg/L的优化条件下电解30 min,废水的脱色率达91.3%,COD降低了62%。机理研究结果表明,电解产生的羟基自由基与甲基橙发生氧化还原反应,破坏了甲基橙的显色基团,使其内部某些化学键发生断裂,从而达到脱色的目的。     

Preparation and Characterization of Xylan Derivatives and Their Blends

Although hemicellulose is found widely in nature, it is currently under-utilized as a raw material for commercial applications. It would be desirable to find new uses for hemicellulose in order to add value to this agro-based material. A common type of hemicellulose is xylan, which is found in a number of wood species and in cotton. In this work we prepared cationic and anionic xylan derivatives and characterized them by ¹³C NMR, FT-IR, size exclusion chromatography (SEC), thermal analysis, and rheology. In particular, the ¹³C NMR spectra of carboxymethyl xylan (CMX) and quaternary ammonium-adducted xylan (QAX) were fully assigned with the help of samples with different degrees of substitution. SEC indicated that the beechwood xylan showed a bimodal molecular weight distribution, but with derivatization the distribution tended to become unimodal. Thermal analysis and rheology studies did not uncover any surprises; the solution of xylan and its derivatives exhibited mostly Newtonian behavior. The blends of CMX and QAX produced a precipitate at almost all ratios, indicating the formation of a polyelectrolyte complex. When cationic and anionic xylan samples were added together to paper, the paper dry strength increased. Thus, the combination of cationic/anionic xylan may be of interest in selected applications.     

Production of Curdlan Grown on Cassava Starch Waste Hydrolysates

Cassava starch waste hydrolysates (CSWHs) with different degrees of polymerisation, i.e., CSWHs-1, CSWHs-2 and CSWHs-3, were prepared through the hydrolysis of cassava starch waste with thermostable a-amylase from Thermococcus sp. HJ21. The prepared CSWHs were then used as a carbon source for curdlan production with Alcaligenes faecalis ATCC 31749. The amount of curdlan produced and the glucosyltransferase activity during curdlan synthesis increased more obviously when CSWHs-2 was used as the carbon source than when glucose was used. Using both carbon sources, the maximum curdlan production was observed at day 5, and the maximum glucosyltransferase activity was observed at day 4. Glucosyltransferase activity decreased thereafter, and biomass continued to increase until the end of the experiment (day 6). Results indicated that the enhanced curdlan production with CSWHs as the carbon source was highly correlated with glucosyltransferase activity.     

Enhanced Interfacial Adhesion and Characterisation of Recycled Natural Fibre-Filled Biodegradable Green Composites

The structural, thermal, mechanical, and biodegradable properties of composite materials made from polylactide (PLA) and agricultural residues (arrowroot (Maranta arundinacea) fibre, AF) were evaluated. Melt blended glycidyl methacrylate-grafted polylactide (PLA-g-GMA) and coupling agent-treated arrowroot fibre (TAF) formed the PLA-g-GMA/TAF composite, which had better properties than the PLA/AF composite. The water resistance of the PLA-g-GMA/TAF composite was greater than that of the PLA/AF composite; the release of PLA in water from the PLA/AF and PLA-g-GMA/TAF composites indicated good biological activity. The PLA-g-GMA/TAF material had better mechanical properties than PLA/AF. This behaviour was attributed to better compatibility between the grafted polymer and TAF. The results indicated that the T_g of PLA was increased by the addition of fibre, which may have improved the heat resistance of PLA. Furthermore, the mass losses following burial in soil compost indicated that both materials were biodegradable, especially at high levels of AF or TAF substitution.     

Preparation and Characterization of Collagens from the Skin of Northern Snakehead (<Emphasis Type="Italic">Channa argus)</Emphasis>

Channa argus, a type of snakehead fish native to China, is a popular food fish in certain Asian countries but is a known destructive invasive species in the US. In this study, the two collagens, i.e. acid-soluble collagen (ASC) and pepsin-solubilized collagen (PSC), were obtained from C. argus skin. The yield of ASC was 28.0% and that of PSC was 16.8% on the dry bases. The collagens were identified as the collagen of type I by SDS–PAGE patterns. The Tds were approximately 27.0?°C. Similar ultraviolet spectra of both collagens were observed. Fourier Transform infrared spectra indicated PSC structure had a little change due to the loss of terminal domains by pepsin digestion. The results of XRD proved that the two collagens retained their helical structures. The results suggest that the collagens isolated from C. argus can potentially be alternative sources of vertebrate collagens for use in the food and other industries.     

High Toughness and Fast Crystallization Poly(Lactic Acid)/Polyamide 11/SiO<Subscript>2</Subscript> Composites

A poly(lactic acid) (PLA)/polyamide 11 (PA11)/SiO₂ composite was mixed from PLA, PA11, and nanosilica particles through twin-screw extrusion. The PLA/PA11/SiO₂ composite was evaluated with tensile and Izod impact tests, light transmission and haze measurement, and isothermal and nonisothermal crystallization behavior determinations. The PLA/PA11/SiO₂ (97.0/3.0) composite had approximately 10.8% less ultimate tensile strength than neat PLA, but it had greater ductility and approximately ninefold greater elongation at break. A dimple morphology was observed on the fractural surface of the PLA/PA11/SiO₂ composite, indicating that the incorporation of PA11 and nanosilica particles increased the ductility of the PLA matrix. PLA with less than 3 wt% of PA11 and 0.5 phr of nanosilica particles had an Izod impact strength of 8.72 kJ/m². PA11 and nanosilica particles effectively toughened this PLA polymer; they accelerated both isothermal and nonisothermal crystallization rates and increased the crystallinities of the resulting composites under isothermal and nonisothermal crystallization processes.     

Comparative study on performances of a heat-pipe PV/T system and a heat-pipe solar water heating system

The heat-pipe solar water heating (HP-SWH) system and the heat-pipe photovoltaic/thermal (HP-PV/T) system are two practical solar systems, both of which use heat pipes to transfer heat. By selecting appropriate working fluid of the heat-pipes, these systems can be used in the cold region without being frozen. However, performances of these two solar systems are different because the HP-PV/T system can simultaneously provide electricity and heat, whereas the HP-SWH system provides heat only. In order to understand these two systems, this work presents a mathematical model for each system to study their one-day and annual performances. One-day simulation results showed that the HP-SWH system obtained more thermal energy and total energy than the HP-PV/T system while the HP-PV/T system achieved higher exergy efficiency than the HP-SWH system. Annual simulation results indicated that the HP-SWH system can heat the water to the available temperature (45°C) solely by solar energy for more than 121 days per year in typical climate regions of China, Hong Kong, Lhasa, and Beijing, while the HP-PV/T system can only work for not more than 102 days. The HP-PV/T system, however, can provide an additional electricity output of 73.019 kWh/m², 129.472 kWh/m², and 90.309 kWh/m² per unit collector area in the three regions, respectively.     

The determination and matching analysis of pinch point temperature difference in evaporator and condenser of organic rankine cycle for mixed working fluid

Exergo-economic analysis of the pinch point temperature difference (PPTD) in both evaporator and condenser of sub-critical organic Rankine cycle system (ORCs) are performed based on the first and second laws of thermodynamics. Taking mixture R13I1/R601a as a working fluid and the annual total cost per net output power Z as exergo-economic performance evaluation criterion, the effects of PPTD in evaporator ΔT_e, and the PPTD ratio of condenser to evaporator y, on the exergo-economic performance of ORCs are analyzed. Moreover, how some other parameters influence the optimal PPTD in evaporator ΔT_e,opt and the optimal PPTD ratio of condenser to evaporator y_opt are also discussed. It has been found that the exergo-economic performance of ORCs is remarkably influenced by ΔT_e and y, and there exists ΔT_e,opt and y_opt. In addition, ΔT_e,opt and y_opt are affected by heat transfer coefficient ratio of condenser to evaporator ß, the temperature of working fluid at dew point in condenser T_1a, and composition of R13I1/R601a: larger ß and T_1a lead to lower ΔT_e,opt and y_opt; by contraries, larger mass fraction of R13I1 makes ΔT_e,opt and y_opt increase, and y_opt increases linearly. The effects of the temperature of working fluid at bubble point in evaporator T_3a, mass flow rate of exhaust flue gas m_g, and inlet temperature of exhaust flue gas T_gi on ΔT_e,opt and y_opt are very slight. For comparison, three additional working fluids, namely R601a, R245fa, and 0.32R245fa/0.68R601a, are also taken into account.