磁性纳米铁对厌氧颗粒污泥特性及其微生物群落的影响

考察了磁性纳米铁(Fe3O4NPs)对厌氧颗粒污泥溶解性微生物产物(SMP)、疏松胞外聚合物(LB-EPS)、紧密胞外聚合物(TB-EPS)的影响,同时利用高通量测序技术对厌氧颗粒污泥内微生物群落结构的变化进行了分析.结果表明,在长期接触实验过程中,投加Fe3O4NPs的反应器对COD去除率为83.6%,与对照组相比降低了5.7%.对照组与实验组中厌氧颗粒污泥TB-EPS含量(以VSS计)分别为178.20 mg·g-1和138.24 mg·g-1,而SMP含量分别为34.88 mg·L-1和27.44 mg·L-1;同时投加Fe3O4NPs后,在LB-EPS三维荧光(EEM)光谱中,紫外光区类腐殖酸荧光峰消失,辅酶F420荧光峰强度有所降低.在长期接触实验后,甲烷杆菌属(Methanobacterium)所占比例从76.15%增至86.76%,而甲烷丝菌属(Methanothrix)所占比例从17.1%降至7.51%,Methanothrix对于Fe3O4NPs更为敏感;总细菌群落变化明显,其中变形菌门(Proteobacteria)所占比例从66.44%降至47.16%,放线菌门(Actinobacteria)所占比例从8.97%增至17.33%,拟杆菌门(Bacteroidetes)所占比例从8.07%增至17.74%,厚壁菌门和拟杆菌门比例的增加对有机物的厌氧水解过程发挥积极的作用.     

分子筛脱硅对其结构与吸附氨氮性能的影响

为提高分子筛吸附氨氮的能力,采用碱蚀法对4种不同硅铝比ZSM5型分子筛进行脱硅处理,对比了脱硅前后吸附氨氮性能的差异;结合X射线衍射、扫描电镜等分析手段观察了其孔隙与晶体结构、表面形貌的变化,同时借助X射线荧光光谱、傅里叶红外光谱等表征手段分析了其内部元素组成与骨架基团的变化;考察了分子筛脱硅处理对改善其吸附氨氮性能的影响机制.结果表明,分子筛经脱硅后氨氮吸附量大幅提高,硅铝比越大吸附氨氮性能改善越显著,其中,硅铝比最小的ZSM5-27型分子筛脱硅后的氨氮平衡吸附量由5.81mg/g上升至10.44mg/g,上升幅度亦达79.7%;碱蚀脱硅处理有效降低了ZSM5型分子筛的硅铝比,分子筛硅铝比越大降低越显著.分子筛脱硅后,其介孔比表面积与比孔容增加、孔径分布变得宽泛;晶体结构仍保持完整、晶粒形态变得更加清晰规整;离子交换容量增加、硅/铝氧四面体结构单元作用增强.碱蚀法对ZSM5型分子筛具有骨架脱硅补铝、疏通孔道等多重作用,脱硅后分子筛活性位点增加、氨离子扩散阻力下降,吸附性能得到改善.     

Pilot-scale experiments on multilevel contact oxidation treatment of poultry farm wastewater using saran lock carriers under different operation model

A pilot-scale multilevel contact oxidation reactors system, coupled with saran lock carriers,was applied for the treatment of poultry farm wastewater. The removal efficiencies of CODcr, ammonia, and the total nitrogen as well as the elimination performance of CODcr and total nitrogen along the three-level contact oxidation tanks under six designed operational models were investigated. Based on the performance of the nitrogen removal of the saran lock carriers and the distribution of anoxic–aerobic interspace under the suitable operation model, the mechanism of nitrogen removal of the system was also explored. The results revealed that the intermittent aeration under parallel model is the most suitable operation model, while the removal efficiencies of CODcr, ammonia, and the total nitrogen were 86.86%, 84.04%, and 80.96%, respectively. The effluent concentration of CODcr,ammonia, and the total nitrogen were 55.6 mg/L, 8.3 mg/L, and 12.0 mg/L, which satisfy both the discharge standard of pollutants for livestock and poultry breeding industry(GB18596–2001) and the first grade of the integrated wastewater discharge standard(GB 8978–1996). Moreover, the mechanism for the nitrogen removal should be attributed to the plenty of anoxic–aerobic interspaces of the biofilm and the three-dimensional spiral structure of the saran lock carriers, where the oxygen-deficient distribution was suitable for the happening of the simultaneous nitrification and denitrification process. Therefore, the multilevel contact oxidation tanks system is an effective pathway for the treatment of the poultry farm wastewater on the strength of a suitable operation model and novel carriers.     

Enhanced nitrate reduction in water by a combined bio-electrochemical system of microbial fuel cells and submerged aquatic plant Ceratophyllum demersum

High nitrate(NO_3~-)loading in water bodies is a crucial factor inducing the eutrophication of lakes.We tried to enhance NO_3~-reduction in overlying water by coupling sediment microbial fuel cells(SMFCs)with submerged aquatic plant Ceratophyllum demersum.A comparative study was conducted by setting four treatments:open-circuit SMFC(Control),closed-circuit SMFC(SMFC-c),open-circuit SMFC with C.demersum(Plant),and closed-circuit SMFC with C.demersum(P-SMFC-c).The electrochemical parameters were documented to illustrate the bio-electrochemical characteristics of SMFC-c and P-SMFC-c.Removal pathways of NO_3~- in different treatments were studied by adding quantitative~(15)NO_3~- to water column.The results showed that the cathodic reaction in SMFC-c was mainly catalyzed by aerobic organisms attached on the cathode,including algae,Pseudomonas,Bacillus,and Albidiferax.The oxygen secreted by plants significantly improved the power generation of SMFC-c.Both electrogenesis and plants enhanced the complete removal of NO_3~- from the sediment–water system.The complete removal rates of added~(15)N increased by 17.6% and 10.2% for SMFC-c and plant,respectively,when compared with control at the end of experiment.The electrochemical/heterotrophic and aerobic denitrification on cathodes mainly drove the higher reduction of NO_3~- in SMFC-c and plant,respectively.The coexistence of electrogenesis and plants further increased the complete removal of NO_3~- with a rate of 23.1%.The heterotrophic and aerobic denitrifications were simultaneously promoted with a highest abundance of Flavobacterium,Bacillus,Geobacter,Pseudomonas,Rhodobacter,and Arenimonas on the cathode.     

Morphology and composition of particles emitted from a port fuel injection gasoline vehicle under real-world driving test cycles

Traffic vehicles, many of which are powered by port fuel injection (PFI) engines, are major sources of particulate matter in the urban atmosphere. We studied particles from the emission of a commercial PFI-engine vehicle when it was running under the states of cold start, hot start, hot stabilized running, idle and acceleration, using a transmission electron microscope and an energy-dispersive X-ray detector. Results showed that the particles were mainly composed of organic, soot, and Ca-rich particles, with a small amount of S-rich and metal-containing particles, and displayed a unimodal size distribution with the peak at 600?nm. The emissions were highest under the cold start running state, followed by the hot start, hot stabilized, acceleration, and idle running states. Organic particles under the hot start and hot stabilized running states were higher than those of other running states. Soot particles were highest under the cold start running state. Under the idle running state, the relative number fraction of Ca-rich particles was high although their absolute number was low. These results indicate that PFI-engine vehicles emit substantial primary particles, which favor the formation of secondary aerosols via providing reaction sites and reaction catalysts, as well as supplying soot, organic, mineral and metal particles in the size range of the accumulation mode. In addition, the contents of Ca, P, and Zn in organic particles may serve as fingerprints for source apportionment of particles from PFI-engine vehicles.     

Temporal variability of visibility and its parameterizations in Ningbo, China

Simultaneous and continuous measurements of visibility, meteorological parameters and air pollutants were carried out at a suburban site in Ningbo from June 1, 2013 to May 31,2015. The characteristics of visibility and their relationships with air pollutants and meteorological factors were investigated using multiple statistical methods. Daily visibility ranged from 0.6 to 34.1 km, with a mean value of 11.8 km. During the 2-year experiment,43.4% of daily visibility was found to be less than 10.0 km and only 9.2% was greater than 20.0 km. Visibility was lower in winter with a frequency of 53.4% in the range of 0.0–5.0 km.Annual visibility had an obvious diurnal variation, with the lowest and highest visibility being 7.5 km at approximately 06:00 local time and 15.6 km at approximately 14:00 local time, respectively. Multiple correspondence analysis(MCA) indicated that the different ranges of visibility were significantly affected by different levels of pollutants and meteorological conditions. Based on the analyses, visibility was found to be an exponential function of PM_(2.5) concentrations within a certain range of relative humidity. Thus, nonlinear models combining multiple linear regressions with exponential regression were subsequently developed using the data collected from June 2014 to May 2015, and the data from June 2013 to May 2014 was used to evaluate the performance of the model. It was demonstrated that the derived models can quantitatively describe the relationships between visibility, air quality and meteorological parameters in Ningbo.     

喷灌和沟灌方式对农田土壤NH3挥发的影响

研究了2016和2017年传统灌溉（沟灌）和节水灌溉（喷灌）方式氨（NH₃）挥发的季节年际动态变化特征及其影响因素.采用通气法进行原位监测,分析了土壤温度、体积含水量、铵态氮（NH₄⁺-N）、硝态氮（NO₃^--N）以及气温降水等因素对NH₃挥发的影响.结果表明,NH₃挥发速率的峰值出现在施用氮肥后1~2周,喷灌有效降低NH₃挥发峰值,喷灌和沟灌的NH₃挥发速率峰值在2016年分别为2.67kg/（hm²·d）和11.11kg/（hm²·d）,2017年分别为2.42kg/（hm²·d）和11.73kg/（hm²·d）;马铃薯生长季NH₃挥发存在明显的季节变化,挥发高峰主要发生在7~8月,追肥期高于基肥期.2016~2017年农田土壤NH₃累积挥发量均表现为喷灌<沟灌,与沟灌相比,喷灌分别减少58.15%和43.55%.NH₃挥发速率与土壤温度呈显著正相关（P<0.05）,与体积含水量、NH₄⁺-N、NO₃^--N浓度呈极显著正相关（P<0.01）.     

基于DTT法测量广州市区PM2.5的氧化潜势

大气颗粒物氧化潜势（Oxidative potential）常用于表征颗粒物对人体健康的影响.二硫苏糖醇（DTT）法是近年发展的一种测定颗粒物氧化潜势的方法,本研究改进了该方法的颗粒物提取方式和反应流程,并开展了广州市区PM_2.5氧化潜势（DTT_m&DTT_v）的测量.结果表明,广州市区2018年1月和4月PM_2.5的DTT_m值分别为（13.47±3.86）,（14.66±4.49）pmol/（min·μg）,DTT_v值分别为（4.67±1.06）,（4.45±1.02）nmol/（min·m³）,与国内外研究结果相当.DTT_v与PM_2.5质量浓度、OC、EC、BC具有较强的相关性,但DTT_m与以上参数相关性低,说明含碳组分不是广州市PM_2.5氧化潜势的主要贡献者.     

基于Revised IMPROVE方法和MIE方法计算北京地区气溶胶消光系数的对比分析

目的对比分析IMPROVE方程的改进算法(Revised IMPROVE)和MIE方法在北京地区计算消光系数的适用性。方法基于2012年6月3日至6月30日北京地区大气颗粒物成分的浓度观测数据,分别采用Revised IMPROVE和MIE方法计算颗粒物的消光系数,其中MIE方法的粒径分布采用总量双峰分布体积谱和化学组分体积谱两种方案进行循环试验获取最优拟合结果,使用散射积分浊度计和黑碳仪的实测数据对计算结果进行对比分析。结果 RevisedIMPROVE方程、总量双峰体积谱MIE方法和化学组分体积谱MIE方法都能较好地计算出了大气颗粒物消光系数,与观测结果回归方程的相关系数R分别达到0.952、0.9686和0.9734。体积谱分布参数的循环试验方法还同时可以获得气溶胶的体积谱分布参数,总量双峰体积谱和化学组分体积谱MIE方法得到的细颗粒和粗颗粒几何平均粒径分别为0.74、7.5μm和0.48、6.0μm。结论采用化学组分体积谱MIE方法计算的消光系数与观测结果最为接近,Revised IMPROVE方程也有较好的准确性,采用化学组分体积谱MIE方法得到的颗粒物体积谱峰值与实际观测结果也较为一致。     

废弃硅钼棒循环再利用制备MoSi2 基抗氧化涂层

目的在实现钼资源循环再利用的同时,提高钼合金高温抗氧化性能。方法将废弃硅钼棒破碎、球磨制成粉末,并结合玻璃粉和硅粉作为原料,采用浆料法在钼基体上制备MoSi_2基抗氧化涂层。通过扫描电子显微镜、X射线衍射和1400℃静态等温氧化实验等分析涂层的微观组织、结构及抗氧化性能。结果制备的MoSi_2基抗氧化涂层厚度约500μm,涂层整体上呈现出相对致密的结构。在1400℃氧化20h后,涂层质量增量为5.88 mg/cm2,呈现出较好的防氧化效果。结论利用浆料法,以废弃硅钼棒为原料,在实现钼资源回收再利用的同时,为钼合金表面制备具有较好抗氧化性能的MoSi_2基抗氧化涂层。氧化过程中,涂层在表面形成了一层致密的SiO2玻璃,具有较强的阻氧能力,减少氧气向基体的渗入,可以在高温氧化环境有效提升钼基体的抗氧化能力。