Gas-phase chemistry of benzyl alcohol: Reaction rate constants and products with OH radical and ozone

A bimolecular rate constant, k_{OH+Benzyl alcohol}, of (28 ± 7) × 10^?12 cm³ molecule^?1 s^?1 was measured using the relative rate technique for the reaction of the hydroxyl radical (OH) with benzyl alcohol, at (297 ± 3) K and 1 atm total pressure. Additionally, an upper limit of the bimolecular rate constant, k_{O3+Benzyl alcohol}, of approximately 6 × 10^?19 cm³ molecule^?1 s^?1 was determined by monitoring the decrease in benzyl alcohol concentration over time in an excess of ozone (O₃). To more clearly define part of benzyl alcohol's indoor environment degradation mechanism, the products of the benzyl alcohol + OH were also investigated. The derivatizing agents O-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine (PFBHA) and N,O-bis(trimethylsilyl) trifluoroacetamide (BSTFA) were used to positively identify benzaldehyde, glyoxal and 4-oxopentanal as benzyl alcohol/OH reaction products. The elucidation of other reaction products was facilitated by mass spectrometry of the derivatized reaction products coupled with plausible benzyl alcohol/OH reaction mechanisms based on previously published volatile organic compound/OH gas-phase reaction mechanisms.     

Aerosol formation yields from the reaction of catechol with ozone

The formation of secondary organic aerosol from the gas-phase reaction of catechol (1,2-dihydroxybenzene) with ozone has been studied in two smog chambers. Aerosol production was monitored using a scanning mobility particle sizer and loss of the precursor was determined by gas chromatography and infrared spectroscopy, whilst ozone concentrations were measured using a UV photometric analyzer. The overall organic aerosol yield (Y) was determined as the ratio of the suspended aerosol mass corrected for wall losses (M_o) to the total reacted catechol concentrations, assuming a particle density of 1.4 g cm^?3. Analysis of the data clearly shows that Y is a strong function of M_o and that secondary organic aerosol formation can be expressed by a one-product gas–particle partitioning absorption model. The aerosol formation is affected by the initial catechol concentration, which leads to aerosol yields ranging from 17% to 86%. The results of this work are compared to similar studies reported in the literature.     

Influence of air mass source region on nanoparticle events and hygroscopicity in central Virginia,U.S.

During autumn, 2006, variation in the frequency of aerosol nucleation events, as inferred from nanoparticle growth events, and associated hygroscopicity were investigated as a function of air mass transport history at a mixed deciduous forest in central Virginia, U.S. Above-canopy size distributions of aerosols between 0.012 and 0.700 μm diameter, size-resolved particle hygroscopicity at eight dry diameters between 0.012 and 0.400 μm, and cloud condensation nuclei (CCN) activity were characterized. Air mass back trajectories were clustered to identify source regions. Growth events were most frequent in fast-moving air masses (mean = 9 m s^?1) that originated over the north central U.S. Under these flow regimes, mean values for preexisting sub-μm aerosol number concentrations (4700 cm^?3), corresponding surface area (142 μm² cm^?3), air temperature (6.2 °C), and relative humidity (RH, 49.4%) were relatively low compared to other regimes. Under stagnant flow conditions (mean = 3 m s^?1), mean number concentrations were higher (>6000 cm^?3) and size fractions <0.1 μm diameter exhibited enhanced hygroscopicity compared to other source regions. These results indicate that precursors emitted into relatively clean, cold, and dry air transported over the southeastern U.S. reacted to form condensable intermediates that subsequently produced new aerosols via nucleation and growth. This pathway was an important source for CCN. During events in October, nanoparticles were produced in greater numbers and grew more rapidly compared to November and December.     

Simulation of global warming potential (GWP) from rice fields in the Tai-Lake region,China by coupling 1:50,000 soil database with DNDC model

Quantifying greenhouse gas (GHG) emissions from wetland ecosystems is a relatively new issue in global climate change studies. China has approximately 22% of the world's rice paddies and 38% of the world's rice production, which are crucial to accurately estimate the global warming potential (GWP) at regional scale. This paper reports an application of a biogeochemical model (DeNitrification and DeComposition or DNDC) for quantifying GWP from rice fields in the Tai-Lake region of China. For this application, DNDC is linked to a 1:50,000 soil database, which was derived from 1107 paddy soil profiles compiled during the Second National Soil Survey of China in the 1980–1990s. The simulated results show that the 2.34 Mha of paddy soil cultivated in rice–wheat rotation in the Tai-Lake region emitted about ?1.48 Tg C, 0.84 Tg N and 5.67 Tg C as CO₂, N₂O, and CH₄ respectively, with a cumulative GWP of 565 Tg CO₂ equivalent from 1982 to 2000. As for soil subgroups, the highest GWP (26,900 kg CO₂ equivalent ha^?1 yr^?1) was linked to gleyed paddy soils accounting for about 4.4% of the total area of paddy soils. The lowest GWP (5370 kg CO₂ equivalent ha^?1 yr^?1) was associated with submergenic paddy soils accounting for about 0.32% of the total area of paddy soils. The most common soil in the area was hydromorphic paddy soils, which accounted for about 53% of the total area of paddy soils with a GWP of 12,300 kg CO₂ equivalent ha^?1 yr^?1. On a regional basis, the annual averaged GWP in the polder, Tai-Lake plain, and alluvial plain soil regions was distinctly higher than that in the low mountainous and Hilly soil regions. As for administrative areas, the average annual GWP of counties in Shanghai city was high. Conversely, the average annual GWP of counties in Jiangsu province was low. The high variability in soil properties throughout the Tai-Lake region is important and affects the net greenhouse gas emissions. Therefore, the use of detailed soil data sets with high-resolution digital soil maps is essential to improve the accuracy of GWP estimates with process-based models at regional and national scales.     

Analysis of air pollution data at a mixed source location using boosted regression trees

This paper explores the use of boosted regression trees to draw inferences concerning the source characteristics at a location of high source complexity. Models are developed for hourly concentrations of nitrogen oxides (NO_X) close to a large international airport. Model development is discussed and methods to quantify model uncertainties developed. It is shown that good explanatory models can be developed and further, allowing for interactions between model variables significantly improves the model fits compared with non-interacting models. Methods are used to determine which variables exert most influence over predicted concentrations and to explore the NO_X dependency for each. Model predictions are used to estimate aircraft take-off contributions to total concentrations of NO_X and determine how these predictions are affected by annual variations in meteorological conditions and runway use patterns. Furthermore, the results relating to the aircraft contributions to total NO_X concentration are compared with those from a more detailed independent field campaign. Finally, we find empirical evidence that plumes from larger aircraft disperse more rapidly from the point of release compared with smaller aircraft. The reasons for this behaviour and the implications are discussed.     

Further studies on the uptake of persistent organic pollutants (POPs) by polyurethane foam disk passive air samplers

Passive air samplers (PAS) can be used to monitor semi-volatile organic compounds in the atmosphere. Polyurethane foam (PUF) disks are a popular sampling medium because they have a high retention capacity for such compounds. This paper reports a highly time-resolved uptake study, to derive uptake rate data under field conditions, and investigate the effects of using different foam densities on the uptake rate. PUF disks were deployed alongside an active sampler, for periods of up to 12 weeks. The uptake rates were measured for a range of gas- and particle-bound persistent organic pollutants (polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs)), of different properties, to explore whether gas–particle partitioning affected uptake rate. Uptake rates for two different densities of foam (0.021 and 0.035 g cm^?3) were not statistically significantly different from each other. Uptake rates of light PCBs averaged ～6.5 m³ day^?1, somewhat higher than in previous studies; higher wind speeds and lower temperatures in this study are the likely reason for this difference. The study showed: i) the uptake rate of the compound with lowest K_OA considered in this study (PCB-28/31) declined in the later weeks, indicating an approach to equilibrium; ii) uptake rates of lighter BDEs and heavier PCBs (compounds of intermediate K_OA in this study) remain similar throughout the study period, indicating that they are not approaching equilibrium during the 12-week-study; iii) uptake rates were typically: ～8 m³ day^?1 for PCB-52; ～9.5 m³ day^?1 for PCB-95; ～11 m³ day^?1 for BDE-28 and ～2 m³ day^?1 BDE-99. The latter compound has an important particle-bound component and this lowers the sampling rate compared to predicted uptake rates for compounds which are in the gas phase only. It is shown that knowledge of gas–particle partitioning is needed to correct for this effect, and to improve predicted uptake rates.     

A comparison of mesh-adaptive LES with wind tunnel data for flow past buildings: Mean flows and velocity fluctuations

In this paper we address two important aspects of micro-scale urban airflow model evaluation: (a) the identification of key flow features as dictated by the physics of the problem and as captured by the simulations, and (b) the comparison of important model output parameters (mean flows and fluctuations) with experimental data. A series of mesh-adaptive large eddy simulations (LES) was carried out for the study of air flows within two intersecting street canyons with varying building configurations. The novelty of the approach lies in the combination of LES with mesh adaptivity, which allows a variable-filter length and the implementation of an anisotropic eddy-viscosity model. Both coarse and fine-mesh simulations were carried out, using single and parallel-processor systems respectively. The simulations showed clearly that the expected flow patterns such as the street canyon recirculation and the street-mouth vortices, as well as the exchange of air flow at the street intersections, can readily be captured by the mesh-adaptive LES.In addition, the detailed comparisons of mean flows and fluctuations of the resolved velocity field with the measured data showed that the simulation results agreed well with the patterns and trends of the wind tunnel measurements. In most cases the finer-mesh simulations improved considerably the accuracy of the mean flows, especially for the symmetrical configuration. The improvement in the predicted fluctuations was less obvious, with several detector locations underpredicting the measured values, although the overall comparison was also satisfactory. The typical errors for the mean flows for all three building configurations were less than 30%, whilst for the velocity fluctuations less that 40%. Both the simulated means flows and turbulence levels were generally more accurate in the streets parallel to the wind (streamwise direction) than in the streets normal to the wind.     

Evaluation of the aggressive potential of marine chloride and sulfate salts on mortars applied as renders in the Metropolitan Region of Salvador--Bahia, Brazil

In recent years, growing interest has focused on determining the performance of materials and evaluating the service life of structures exposed to various environmental forces. In this context, the determination of the aggressive potential of marine salts on mortars used as external renders is critical. The present study aimed to evaluate the spatial distribution of marine salts relative to distance from the sea. This was done by monitoring the deposition rate of chlorides and sulfates in wet candle sensors, located at nine stations scattered around the Metropolitan Region of Salvador, state of Bahia, Brazil. The study also determined the effectiveness of water-soluble salts at penetrating three different types of mortars of varying cement content via deposition and diffusion. The methodology employed enabled an evaluation of the efficiency of the monitoring sensors' measurement of the aggressiveness potential of local marine aerosol, and determination of the comparative performance of the three mortars tested, from the standpoint of resistance to salt penetration. The type and amount of salts captured both in solution and in powder samples extracted from the mortars were determined by ion chromatography. The analysis of the various types of mortars tested indicated which types are more resistant to the aggressive potential of the region's marine aerosol and the distance from the shore where local buildings are liable to be most strongly affected.