A comparison of mesh-adaptive LES with wind tunnel data for flow past buildings: Mean flows and velocity fluctuations

In this paper we address two important aspects of micro-scale urban airflow model evaluation: (a) the identification of key flow features as dictated by the physics of the problem and as captured by the simulations, and (b) the comparison of important model output parameters (mean flows and fluctuations) with experimental data. A series of mesh-adaptive large eddy simulations (LES) was carried out for the study of air flows within two intersecting street canyons with varying building configurations. The novelty of the approach lies in the combination of LES with mesh adaptivity, which allows a variable-filter length and the implementation of an anisotropic eddy-viscosity model. Both coarse and fine-mesh simulations were carried out, using single and parallel-processor systems respectively. The simulations showed clearly that the expected flow patterns such as the street canyon recirculation and the street-mouth vortices, as well as the exchange of air flow at the street intersections, can readily be captured by the mesh-adaptive LES.In addition, the detailed comparisons of mean flows and fluctuations of the resolved velocity field with the measured data showed that the simulation results agreed well with the patterns and trends of the wind tunnel measurements. In most cases the finer-mesh simulations improved considerably the accuracy of the mean flows, especially for the symmetrical configuration. The improvement in the predicted fluctuations was less obvious, with several detector locations underpredicting the measured values, although the overall comparison was also satisfactory. The typical errors for the mean flows for all three building configurations were less than 30%, whilst for the velocity fluctuations less that 40%. Both the simulated means flows and turbulence levels were generally more accurate in the streets parallel to the wind (streamwise direction) than in the streets normal to the wind.     

Think global,act local: The effect of goal and mindset specificity on willingness to donate to an environmental organization

This paper investigated the effect of goal and mindset specificity on goal-related behavior in the environmental domain. Two studies demonstrated that goal-related behavior was maximized when participants focused on an abstract goal in combination with a specific mindset, or when they focused on a specific goal in combination with an abstract mindset. When goals and mindsets instead matched in terms of abstractness, goal-related behavior was reduced. Study 2 demonstrated that the effect of goal specificity on behavior was mediated by different processes in each of the mindset conditions. When mindsets were abstract, self-efficacy mediated the positive effect of specific goals on behavior; when mindsets were specific, the value of collective environmental action mediated the positive effect of abstract goals on behavior. The results are discussed in the framework of a complementarity approach. It is argued that complementarity of levels of specificity of goals and mindsets may affect behavior particularly strongly in domains where the discrepancy between the abstract and the specific is large (e.g. the environmental domain).     

Walking in the Irish countryside: landowner preferences and attitudes to improved public access provision

This paper explores the attitudes of landowners across Ireland to the wider provision of public access for recreational walking using a multinomial logit model. The study also investigates the level of compensation required to improve the supply of this public good. Results indicate that 51% of landowners are not willing to provide access (non-providers), 21% are willing to provide access free of charge (free providers) and 28% seek compensation (willing providers). The findings indicate that participation by landowners in a proposed public access scheme is influenced by landowners' experience with walkers, farm type, farm insurance costs, household demographics, regional variations, opportunity cost of land and participation in other agri-environment schemes. Mean willingness-to-accept for landowners willing to facilitate improved public access for walking was found to be €0.27 per metre of walkway.     

Monitoring household waste recycling centres performance using mean bin weight analyses

This paper describes a modelling approach used to investigate the significance of key factors (vehicle type, compaction type, site design, temporal effects) in influencing the variability in observed nett amenity bin weights produced by household waste recycling centres (HWRCs). This new method can help to quickly identify sites that are producing significantly lighter bins, enabling detailed back-end analyses to be efficiently targeted and best practice in HWRC operation identified. Tested on weigh ticket data from nine HWRCs across West Sussex, UK, the model suggests that compaction technique, vehicle type, month and site design explained 76% of the variability in the observed nett amenity weights. For each factor, a weighting coefficient was calculated to generate a predicted nett weight for each bin transaction and three sites were subsequently identified as having similar characteristics but returned significantly different mean nett bin weights. Waste and site audits were then conducted at the three sites to try and determine the possible sources of the remaining variability. Significant differences were identified in the proportions of contained waste (bagged), wood, and dry recyclables entering the amenity waste stream, particularly at one site where significantly less contaminated waste and dry recyclables were observed.     

Sustainable forest management in a mountain region in the Central Western Carpathians,northeastern Slovakia: the role of climate change

European forestry is facing many challenges, including the need to adapt to climate change and an unprecedented increase in forest damage. We investigated these challenges in a Norway spruce-dominated mountain region in Central Europe. We used the model Sibyla to explore forest biomass production to the year 2100 under climate change and under two alternative management systems: the currently applied management (CM), which strives to actively improve the forest’s adaptive capacity, and no management (NM) as a reference. Because biodiversity is thought to have mostly positive effects on the adaptive capacity of forests and on the quality of ecosystem services, we explored how climate change and management affect indicators of biodiversity. We found a differential response across the elevation-climatic gradient, including a drought-induced decrease in biomass production over large areas. With CM, the support of non-spruce species and the projected improvement of their growth increased tree species diversity. The promotion of species with higher survival rates led to a decrease in forest damage relative to both the present conditions and NM. NM preserved the high density of over-matured spruce trees, which caused forest damage to increase. An abundance of dead wood and large standing trees, which can increase biodiversity, increased with NM. Our results suggest that commercial spruce forests, which are not actively adapted to climate change, tend to preserve their monospecific composition at a cost of increased forest damage. The persisting high rates of damage along with the adverse effects of climate change make the prospects of such forests uncertain.     

Characterization of summertime coarse particulate matter in the Desert Southwest—Arizona,USA

A year-long study was conducted in Pinal County, AZ, to characterize coarse (2.5 – 10 μm aerodynamic diameter, AD) and fine (< 2.5 μm AD) particulate matter (PMc and PMf, respectively) to further understand spatial and temporal variations in ambient PM concentrations and composition in rural, arid environments. Measurements of PMc and PMf mass, ions, elements, and carbon concentrations at one-in-six day resolution were obtained at three sites within the region. Results from the summer of 2009 and specifically the local monsoon period are presented.

The summer monsoon season (July – September) and associated rain and/or high wind events, has historically had the largest number of PM₁₀ NAAQS exceedances within a year. Rain events served to clean the atmosphere, decreasing PMc concentrations resulting in a more uniform spatial gradient among the sites. The monsoon period also is characterized by high wind events, increasing PMc mass concentrations, possibly due to increased local wind-driven soil erosion or transport. Two PM₁₀ NAAQS exceedances at the urban monitoring site were explained by high wind events and can likely be excluded from PM₁₀ compliance calculations as exceptional events. At the more rural Cowtown site, PM₁₀ NAAQS exceedances were more frequent, likely due to the impact from local dust sources.

PM mass concentrations at the Cowtown site were typically higher than at the Pinal County Housing and Casa Grande sites. Crustal material was equal to 52-63% of the PMc mass concentration on average. High concentrations of phosphate and organic carbon found at the rural Cowtown were associated with local cattle feeding operations. A relatively high correlation between PMc and PMf (R²?=?0.63) indicated that the lower tail of the coarse particle fraction often impacts the fine particle fraction, increasing the PMf concentrations. Therefore, reductions in PMc sources will likely also reduce PMf concentrations, which also are near the value of the 24-hr PM_2.5 NAAQS.

Implications: In the desert southwest, summer monsoons are often associated with above average PM₁₀ (<10 μm AD) mass concentrations. Competing influences of monsoon rain and wind events showed that rain suppresses ambient concentrations while high wind increase them. In this region, the PMc fraction dominates PM₁₀ and crustal sources contribute 52-63% to local PMc mass concentrations on average. Cattle feedlot emissions are also an important source and a unique chemical signature was identified for this source. Observations suggest monsoon wind events alone cannot explain PM₁₀ NAAQS exceedances, thus requiring these values to remain in compliance calculations rather than being removed as exceptional wind events.     

A Socio-Ecological Assessment Aiming at Improved Forest Resource Management and Sustainable Ecotourism Development in the Mangroves of Tanbi Wetland National Park, The Gambia, West Africa

Although mangroves dominated by Avicennia germinans and Rhizophora mangle are extending over 6000 ha in the Tanbi Wetland National Park (TWNP) (The Gambia), their importance for local populations (both peri-urban and urban) is not well documented. For the first time, this study evaluates the different mangrove resources in and around Banjul (i.e., timber, non-timber, edible, and ethnomedicinal products) and their utilization patterns, including the possibility of ecotourism development. The questionnaire-based results have indicated that more than 80% of peri-urban population rely on mangroves for timber and non-timber products and consider them as very important for their livelihoods. However, at the same time, urban households demonstrate limited knowledge on mangrove species and their ecological/economic benefits. Among others, fishing (including the oyster—Crassostrea cf. gasar collection) and tourism are the major income-generating activities found in the TWNP. The age-old practices of agriculture in some parts of the TWNP are due to scarcity of land available for agriculture, increased family size, and alternative sources of income. The recent focus on ecotourism (i.e., boardwalk construction inside the mangroves near Banjul city) received a positive response from the local stakeholders (i.e., users, government, and non-government organizations), with their appropriate roles in sharing the revenue, rights, and responsibilities of this project. Though the guidelines for conservation and management of the TWNP seem to be compatible, the harmony between local people and sustainable resource utilization should be ascertained.

Electronic supplementary material

The online version of this article (doi:10.1007/s13280-012-0248-7) contains supplementary material, which is available to authorized users.     

Chitosan/Hydrophilic Plasticizer-Based Films: Preparation,Physicochemical and Antimicrobial Properties

The addition of plasticizers to biopolymer films is a good method for improving their physicochemical properties. The aim of this study was to evaluate the effect of chitosan (CHI) blended with two hydrophilic plasticizers glycerol (GLY) and sorbitol (SOR), at two concentrations (20 and 40 wt%) on their mechanical, thermal, barrier, structural, morphological and antimicrobial properties. The chitosan was prepared through the alkaline deacetylation of chitin obtained from fermented lactic from shrimp heads. The obtained chitosan had a degree of deacetylation (DA) of 84 ± 2.7 and a molecular weight of 136 kDa, which indicated that a good film had formed. The films composed of CHI and GLY (20 wt%) exhibited the best mechanical properties compared to the neat chitosan film. The percentage of elongation at break increase to over 700 % in the films that contained 40 % GLY, and these films also exhibited the highest values for the water vapor transmission rate (WVTR) of 79.6 ± 1.9 g m² h^?1 and a yellow color (b _o  = 17.9 ± 2.0) compared to the neat chitosan films (b _o  = 8.8 ± 0.8). For the structural properties, the Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction analyses revealed an interaction in the acetamide group and changes in the crystallinity of plasticized films. The scanning electron micrographs revealed that all formulations of the chitosan films were smooth, and that they did not contain aggregations, pores or microphase separation. The thermal analysis using differential scanning calorimetry (DSC) revealed a glass transition temperature (Tg) of 130 °C for neat chitosan film, but the addition of SOR or GLY elicited a decrease in the temperature of the peak (120 °C). In addition, the antimicrobial activity of the chitosan films was evaluated against Listeria monocytogenes, and reached a reduction of 2 log after 24 h. The plasticizer concentration of 20 % GLY is sufficient for obtaining flexible chitosan films with good mechanical properties, and it could serve as an alternative as a packaging material to reduce environmental problems associated with synthetic packaging films.     

Contamination of wild-grown edible mushrooms by heavy metals in a former mercury-mining area

The aim of this study was to evaluate the contamination of six edible wild species of mushrooms (Boletus pulverulentus, Cantharellus cibarius, Lactarius quietus, Macrolepiota procera, Russula xerampelina and Suillus grevillei) by heavy metals (Hg, Cd, Pb, Zn, Cu, Ni, Cr, Co, Mn and Fe). Mushroom samples were collected from sites contaminated by emissions from mining and processing of polymetallic ores in operation during the period 1969–1993 in Rudňany, southeast Slovakia. The four study sites spanned up to a 5-km distance from the emission source. The collected mushroom samples were analyzed using Flame Atomic Absorption Spectrophotometry and/or Flame Atomic Absorption Spectrophotometry with graphite furnace. Mercury, Cd and, in some samples, also Pb present the highest risks in terms of contamination of the food chain following subsequent consumption. The content of two metals in the dry matter (dm) of the mushrooms exceeded the limits set by the European Union (EU; Cd: 0.5 mg/kg dm, Pb: 1.0 mg/kg dm). The highest mean contents of the eight metals recorded for S. grevillei were 52.2, 2.15, 107, 104, 2.27, 2.49, 81.6 and 434 mg/kg dm for Hg, Pb, Zn, Cu, Ni, Cr, Mn and Fe, respectively. The highest content of Cd was recorded in M. procera (3.05 mg/kg dm) and that of Co in L. quietus (0.90 mg/kg dm). The calculated weekly intake for Hg, Pb and Cd shows that regular consumption of mushrooms from the studied area poses risks to human health.     

Effects of reduced contaminant loading on downgradient water quality in an idealized two-layer granular porous media

The following explores the issue of how reductions in contaminant loading to plumes will effect downgradient water quality. An idealized scenario of two adjacent layers of uniform geologic media, one transmissive and the other low permeability, is considered. A high concentration source, similar to a thin DNAPL pool, is introduced in the transmissive layer immediately above the low permeability layer. While the source is active, dissolved constituents are driven along the contact by advection and into the low permeability layer by transverse diffusion. Removing the source reverses the concentration gradient between the layers, driving back diffusion of contaminants from the low permeability layer. Laboratory studies involving four contaminants demonstrate that 15 to 44% of the introduced contaminant moves into the low permeability zone (along a distance of 87 cm in a sand tank) over a period of 25 days. The greatest movement of contaminants into the low permeability zone is seen with the contaminants with the greatest sorption coefficients. A unique two-dimensional analytical solution is developed for the two-layer scenario. Processes addressed include advection; transverse dispersion; adsorption and degradation in the transmissive zones; and diffusion, adsorption, and degradation in the low permeability layer. Laboratory data agree favorably with the analytical solutions. Collectively, the laboratory results and analytical solutions provide a basis for testing other modeling approaches that can be applied to more complex problems. A set of field-scale scenarios are considered using the analytical solutions. Results indicate that improvement in water quality associated with source removal diminish with distance downgradient of the source. Furthermore, contaminant degradation and contaminant adsorption in the stagnant zone are shown to be critical factors governing the timing and magnitude of downgradient improvements in water quality. For five of six scenarios considered, observed improvements in water quality 100 m downgradient of the source fall in the range of 1 to 2 orders of magnitude 15 years after complete source removal. The sixth scenario, involving a contaminant half-life of three years and no adsorption, shows greater than three order of magnitude improvements in downgradient water quality within one year of source removal.