Beryllium-7 Measurements in the Houston and Phoenix Urban Areas: An Estimation of Upper Atmospheric Ozone Contributions

Abstract

Natural radionuclides have been proposed as a means of assessing the transport of ozone (O₃) and aerosols in the troposphere. Beryllium-7 (⁷Be) is produced in the upper troposphere and lower stratosphere by the interaction of cosmogenic particles with atmospheric nitrogen and oxygen. ⁷Be has a 53.29-day half-life (478 keV γ) and is known to attach to fine particles in the atmosphere once it is formed. It has been suggested that O₃ from aloft can be transported into rural and urban regions during stratospheric–tropospheric folding events leading to increased background levels of O₃ at the surface. ⁷Be can be used as a tracer of upper atmospheric air parcels and the O₃ associated with them. Aerosol samples with a 2.5-µm cutoff were collected during 12-hr cycles (day/night) for a 30-day period at Deer Park, TX, near Houston, in August– September of 2000, and at Waddell, AZ, near Phoenix, in June–July of 2001. A comparison of ⁷Be levels with 12-hr O₃ averages and maxima shows little correlation. Comparison of nighttime and daytime O₃ levels indicate that during the day, when mixing is anticipated to be higher, the correlation of ⁷Be with O₃ in Houston is approximately twice that observed at night. This is consistent with mixing and with the anticipated loss of O₃ by reaction with nitric oxide (NO) and dry deposition. At best, 30% of the O₃ variance can be explained by the correlation with ⁷Be for Houston, less than that for Phoenix where no significant correlation was seen. This result is consistent with the intercept values obtained for ⁷Be correlations with either O₃ 24-hr averages or O₃ 12-hr maxima and is also in the range of the low O₃ levels (25 ppb) observed at Deer Park during a tropical storm event where the O₃ is attributable primarily to background air masses. That is, maximum background O₃ level contributions from stratospheric sources aloft are estimated to be in the range of 15–30 ppb in the Houston, TX, and Phoenix, AZ, area, and levels above these are because of local tropospheric photochemical production.     

Electrolytic debromination of PBDEs in DE-83 technical decabromodiphenyl ether

Electrochemical debromination of the commercial decabromodiphenyl ether flame retardant DE-83 in partly aqueous tetrahydrofuran (THF) solution gave lower brominated congeners by sequential loss of bromine atoms. Hydrodebromination was most facile for the most heavily brominated congeners. It involves initial electron transfer and proton transfer from water, rather than hydrogen atom abstraction from THF, as shown by experiments with deuterated water. The product distribution from electrolysis involves preferential loss of bromine meta- and para- to the ether linkage, comparable with the products of metabolism of BDE-209 in various organisms. Significantly, the environmentally relevant congeners BDE-47, BDE-99, and BDE-154 were not major products of debromination of BDE-209 by the electron transfer mechanism.     

Managing petroleum refining wastes by thermal desorption

The U.S. Environmental Protection Agency has developed regulations under the Hazardous and Solid Waste Amendments (HSWA) of 1984 to restrict the land disposal of hazardous wastes. As a result of the regulations, all hazardous wastes to be placed on the land must meet treatment standards based on the performance of the best demonstrated available technology (BDAT) identified for individual waste classifications. The Marathon Oil Company is currently evaluating innovative technologies for managing listed waste materials, with a focus on waste minimization and recycling. Remediation Technologies, Inc. (ReTeC) has conducted testing on wastewater treatment sludges from three Marathon refineries using a proprietary thermal desorption technology. The results from these tests have demonstrated that the technology has the ability to consistently meet BDAT treatment standards, while preferentially separating and condensing residual moisture and oils from the material.     

The boiling liquid expanding vapour explosion

The boiling liquid expanding vapour explosion (BLEVE) has existed for a long time and for most of this time it has been cloaked in mystery. Several theories have been put forward to explain this very energetic event but none have been proven. This paper describes a series of tests that have recently been conducted to study this phenomenon.

The study involved ASME code automotive propane tanks with nominal capacities of 400 litres. The tanks were exposed to a combination of pool and/or torch fires. These fire conditions led to thermal ruptures, and in some cases these ruptures resulted in BLEVEs. The variables in the tests were the pressure-relief valve setting, the tank wall thickness, and the fire condition.

In total, 30 tests have been conducted, of which 22 resulted in thermal ruptures. Of those tanks that ruptured, 11 resulted in what we call BLEVEs. In this paper, we have defined a BLEVE as the explosive release of expanding vapour and boiling liquid following a catastrophic tank failure. Non-BLEVEs involved tanks that ruptured but which only resulted in a prolonged jet release.

The objective of this study was to investigate why certain tank ruptures lead to a BLEVE rather than a more benign jet-type release. Data are presented to show how wall temperature, wall thickness, liquid temperature and fill level contribute to the BLEVE process.     

Field trial of a new aeration system for enhancing biodegradation in a biopile

The influence of a new aeration system on the biopile performance was investigated. The purpose was to increase biodegradation efficiency by optimising airflow through the pile. During a 1-month field trial, the performance of a new system using two perforated vertical pipes with wind-driven turbines was compared with that of a standard pile configuration with two horizontal perforated pipes. Both piles were composed of a similar mix of diesel-contaminated soils, woodchips, compost and NPK fertiliser. Hydrocarbons were recovered using solvent extraction, and determined both gravimetrically and by gas chromatography. Total heterotrophs, pH and moisture content were also assessed. Air pressure measurements were made to compare the efficiency of suction in the pipes. Results at the end of the experiment showed that there was no significant difference between the two piles in the total amount of hydrocarbon biodegradation. The normalised degradation rate was, however, considerably higher in the new system than in the standard one, suggesting that the vertical venting method may have improved the efficiency of the biological reactions in the pile. The pressure measurements showed a significant improvement in the suction produced by the new aeration system. However, many factors other than the airflow (oxygen supply) may influence and limit the biodegradation rates, including moisture content, age of contaminants and the climatic conditions. Additional experiments and modelling need to be carried out to explore further the new aeration method and to develop criteria and guidelines for engineering design of optimal aeration schemes in order to achieve maximum biodegradation in biopiles.     

Development of the Spatial Rainfall Generator (SRGEN) for the Agricultural Policy/Environmental Extender Model

Accurate spatial representation of climatic patterns is often a challenge in modeling biophysical processes at the watershed scale, especially where the representation of a spatial gradient in rainfall is not sufficiently captured by the number of weather stations. The spatial rainfall generator (SRGEN) is developed as an extension of the “weather generator” (WXGEN), a component of the Agricultural Policy/Environmental eXtender (APEX) model. SRGEN generates spatially distributed daily rainfall using monthly weather statistics available at multiple locations in a watershed. The spatial rainfall generator as incorporated in APEX is tested on the Cowhouse watershed (1,178 km²) in central Texas. The watershed presented a significant spatial rainfall gradient of 2.9 mm/km in the lateral (north‐south) directions based on four rainfall gages. A comparative analysis between SRGEN and WXGEN indicates that SRGEN performs well (PBIAS = 2.40%). Good results were obtained from APEX for streamflow (NSE = 0.99, PBIAS = 8.34%) and NO₃‐N and soluble P loads (PBIAS ≈ 6.00% for each, respectively). However, APEX underpredicted sediment yield and organic N and P loads (PBIAS: 24.75‐27.90%) with SRGEN, although its uncertainty in output was lower than WXGEN results (PBIAS: ?13.02 to ?46.13%). The overall improvement achieved in rainfall generation by SRGEN is demonstrated to be effective in the improving model performance on flow and water quality output.     

Innovation and Environmental Voluntary Approaches

Criteria have been developed in general terms for evaluating voluntary approaches. Nevertheless, there still remains limited assessment regarding the performance of environmental voluntary approaches as there is a general dearth of empirical information. In relation to innovation and voluntary approaches there are two main schools of thought, namely, the no innovation scenario and innovation through collective learning. This paper outlines the arguments regarding environmental voluntary approaches and innovation and reports on an empirical study of an Irish packaging voluntary agreement. Its findings would indicate that the no innovation scenario is applicable to the Irish packaging voluntary agreement.