PM10 concentration levels at an urban and background site in Cyprus: The impact of urban sources and dust storms

Air quality in Cyprus is influenced by both local and transported pollution, including desert dust storms. We examined PM₁₀ concentration data collected in Nicosia (urban representative) from April 1, 1993, through December 11, 2008, and in Ayia Marina (rural background representative) from January 1, 1999, through December 31, 2008. Measurements were conducted using a Tapered Element Oscillating Micro-balance (TEOM). PM₁₀ concentrations, meteorological records, and satellite data were used to identify dust storm days. We investigated long-term trends using a Generalized Additive Model (GAM) after controlling for day of week, month, temperature, wind speed, and relative humidity. In Nicosia, annual PM₁₀ concentrations ranged from 50.4 to 63.8 μg/m³ and exceeded the EU annual standard limit enacted in 2005 of 40 μg/m³ every year. A large, statistically significant impact of urban sources (defined as the difference between urban and background levels) was seen in Nicosia over the period 2000–2008, and was highest during traffic hours, weekdays, cold months, and low wind conditions. Our estimate of the mean (standard error) contribution of urban sources to the daily ambient PM₁₀ was 24.0 (0.4) μg/m³. The study of yearly trends showed that PM₁₀ levels in Nicosia decreased from 59.4 μg/m³ in 1993 to 49.0 μg/m³ in 2008, probably in part as a result of traffic emission control policies in Cyprus. In Ayia Marina, annual concentrations ranged from 27.3 to 35.6 μg/m³, and no obvious time trends were observed. The levels measured at the Cyprus background site are comparable to background concentrations reported in other Eastern Mediterranean countries. Average daily PM₁₀ concentrations during desert dust storms were around 100 μg/m³ since 2000 and much higher in earlier years. Despite the large impact of dust storms and their increasing frequency over time, dust storms were responsible for a small fraction of the exceedances of the daily PM₁₀ limit.

ImplicationsThis paper examines PM₁₀ concentrations in Nicosia, Cyprus, from 1993 to 2008. The decrease in PM₁₀ levels in Nicosia suggests that the implementation of traffic emission control policies in Cyprus has been effective. However, particle levels still exceeded the European Union annual standard, and dust storms were responsible for a small fraction of the daily PM₁₀ limit exceedances. Other natural particles that are not assessed in this study, such as resuspended soil and sea salt, may be responsible in part for the high particle levels.     

A hybrid biological process of indoor air treatment for toluene removal

Bioprocesses, such as biofiltration, are commonly used to treat industrial effluents containing volatile organic compounds (VOCs) at low concentrations. Nevertheless, the use of biofiltration for indoor air pollution (IAP) treatment requires adjustments depending on specific indoor environments. Therefore, this study focuses on the convenience of a hybrid biological process for IAP treatment. A biofiltration reactor using a green waste compost was combined with an adsorption column filled with activated carbon (AC). This system treated a toluene-micropolluted effluent (concentration between 17 and 52 µg/m³), exhibiting concentration peaks close to 733 µg/m³ for a few hours per day. High removal efficiency was obtained despite changes in toluene inlet load (from 4.2 × 10^?3 to 0.20 g/m³/hr), which proves the hybrid system’s effectiveness. In fact, during unexpected concentration changes, the efficiency of the biofilter is greatly decreased, but the adsorption column maintains the high efficiency of the entire process (removal efficiency [RE] close to 100%). Moreover, the adsorption column after biofiltration is able to deal with the problem of the emission of particles and/or microorganisms from the biofilter.

ImplicationsIndoor air pollution is nowadays recognized as a major environmental and health issue. This original study investigates the performance of a hybrid biological process combining a biofilter and an adsorption column for removal of indoor VOCs, specifically toluene.     

Looking beyond the average agricultural impacts in defining adaptation needs in Europe

The effects of climate change on agriculture are often characterised by changes in the average productivity of crops; however, these indicators provide limited information regarding the risks associated with fluctuations in productivity resulting from future changes in climate variability that may also affect agriculture. In this context, this study evaluates the combined effects of the risks associated with anomalies reflected by changes in the mean crop yield and the variability of productivity in European agro-climatic regions under future climate change scenarios. The objective of this study is to evaluate adaptation needs and to identify regional effects that should be addressed with greater urgency in the light of the risks and opportunities that are identified. The results show differential effects on regional agriculture and highlight the importance of considering both regional average impacts and the variability in crop productivity in setting priorities for the adaptation and maintenance of rural incomes and agricultural insurance programmes.     

Fuel efficiency improvement of a dual-fuel engine fuelled with Honge oil methyl ester (HOME)–bioethanol and producer gas

Renewable and alternative fuels have numerous advantages compared with fossil fuels as they are renewable and biodegradable and provide food and energy security and foreign exchange savings besides addressing environmental concerns and socio-economic issues (Yaliwal et al. 2013. International Journal of Sustainable Engineering, doi:10.1080/19397038.2013.801530. Zhu et al. 2011a, Applied Thermal Engineering 31 (14–15): 2271–2278; Zhu et al. 2011b, Fuel 90: 1743-1750; Banapurmath, Tewari, and Hosmath 2008, Renewable Energy 33: 2007-2018; Banapurmath 2009, “Performance, Combustion and Emission Characteristics of a Single Cylinder Direct Injection CI Engine Operated on Dual Fuel Mode Using Honge Oil and Producer Gas.” PhD thesis, 1–195; Banapurmath et al. 2011, Waste and Biomass Valorization 2: 1–11). In this context, the main objective of the present work is to study methods of biofuel production such as Honge oil methyl ester (HOME) using a conventional transesterification process and bioethanol from the Calliandra calothyrsus shrub using a new pretreatment method known as hydrothermal explosion. Further, experimental investigations were carried out on a single-cylinder, four-stroke, direct-injection stationary diesel engine operating in a dual-fuel mode using HOME, bioethanol and producer gas combinations to determine its performance, combustion and emission characteristics. The performance of the dual-fuel engine was analyzed at optimized engine conditions. HOME-Bioethanol (BE) blends such as HOME+ 5% bioethanol (BE5), HOME+ 10% bioethanol (BE10) and HOME+ 15% bioethanol (BE15) were prepared by adding bioethanol to HOME (on volume basis) in different proportions ranging from 5 to 15% with an increment of 5%. In this present work, the effect of different BE blends on the performance of producer gas fuelled dual fuel engine was studied. Experimental investigation on dual fuel engine using BE5-Producer gas operation resulted in up to 4–9% increased brake thermal efficiency with decreased hydrocarbon (HC), carbon monoxide (CO) and marginally increased nitric oxide (NOx) emission levels compared to HOME-Producer gas, BE10-producer gas and BE15-producer gas mode of operation. However, it was observed that, the overall performance of BE-producer gas operation was found to be lower compared to diesel-producer gas operation.     

Performance,combustion and emission characteristics of a single-cylinder,four-stroke,direct injection diesel engine operated on a dual-fuel mode using Honge oil methyl ester and producer gas derived from biomass feedstock of different origin

Renewable and alternative fuels have numerous advantages compared with fossil fuels, as they are renewable and biodegradable, and provide food and energy security and foreign exchange savings besides addressing environmental concerns and socio-economic issues. In this context, present work was carried out to investigate the feasibility of alternative and renewable fuels derived from biomass feedstock of different origin for engine applications. The present study was also extended to study the effect of producer gas composition derived from different biomass feedstock on the performance, combustion and emission characteristics of a single-cylinder, four-stroke, direct injection stationary diesel engine operated on a dual-fuel mode using Honge oil methyl ester (HOME) and producer gas induction. The performance of the engine was evaluated with a constant injection timing of 27° before top dead centre, an injection pressure of 205 bar for the diesel–producer gas combination and 230 bar for the HOME–producer gas combination and a compression ratio of 17.5. The results showed that the performance of the dual-fuel engine varies with the composition of the producer gas and depends on the type of biomass feedstock used in the gasifier. Experimental investigations on the dual-fuel engine showed that brake thermal efficiency values for the engine operated using HOME–producer gas derived from babul, neem and honge woods were found to be 17.2, 14.3 and 11.56% respectively, compared to 23.8% for diesel–producer gas operation at 80% load. However, the results showed better engine performance with lower exhaust emission levels for the operation of HOME–producer gas derived from the ordinary or babul wood compared with the operation of that derived from the neem and Honge woods. In view of this, present study reveals that use of alternative and renewable fuels for dual fuel engine can be considered as an immediate solution for the development of rural areas and emergency use in the event of severe diesel fuel shortage.     

Effects of compression ratio,swirl augmentation techniques and ethanol addition on the combustion of CNG–biodiesel in a dual-fuel engine

The diminishing resources and continuously increasing cost of petroleum in association with their alarming pollution levels from diesel engines has led to an interest in finding alternative fuels to diesel. Emission control and engine efficiency are two of the most important parameters in current engine design. The impending introduction of emission standards such as Euro IV and Euro V has forced research towards developing new technologies for combating engine emissions. This paper examines the effects of compression ratio, swirl augmentation techniques and ethanol addition on the combustion of compressed natural gas (CNG) blended with Honge oil methyl esters (HOME) in a dual fuel engine. The present results show that the combustion of HOME and 15% ethanol blend with CNG induction in a dual-fuel engine operated in optimized parameters at an injection timing of 27° Before Top Dead Centre and a compression ratio of 17.5 resulted in acceptable combustion emissions and improved brake thermal efficiencies. The implementation of swirl augmentation techniques increased brake thermal efficiencies (BTEs) and considerably reduced combustion emissions such as smoke, HC, CO and NO_x. The addition of ethanol also increased BTEs. However, at more than 15% of ethanol in HOME, NO_x emissions increased dramatically.     

Adaptation options for marine industries and coastal communities using community structure and dynamics

Identifying effective adaptation strategies for coastal communities dependent on marine resources and impacted by climate change can be difficult due to the dynamic nature of marine ecosystems. The task is more difficult if current and predicted shifts in social and economic trends are considered. Information about social and economic change is often limited to qualitative data. A combination of qualitative and quantitative models provide the flexibility to allow the assessment of current and future ecological and socio-economic risks and can provide information on alternative adaptations. Here, we demonstrate how stakeholder input, qualitative models and Bayesian belief networks (BBNs) can provide semi-quantitative predictions, including uncertainty levels, for the assessment of climate and non-climate-driven change in a case study community. Issues are identified, including the need to increase the capacity of the community to cope with change. Adaptation strategies are identified that alter positive feedback cycles contributing to a continued decline in population, local employment and retail spending. For instance, the diversification of employment opportunities and the attraction of new residents of different ages would be beneficial in preventing further population decline. Some impacts of climate change can be combated through recreational bag or size limits and monitoring of popular range-shifted species that are currently unmanaged, to reduce the potential for excessive removal. Our results also demonstrate that combining BBNs and qualitative models can assist with the effective communication of information between stakeholders and researchers. Furthermore, the combination of techniques provides a dynamic, learning-based, semi-quantitative approach for the assessment of climate and socio-economic impacts and the identification of potential adaptation strategies.     

Bages-Sigean and Canet-St Nazaire lagoons (France): physico-chemical characteristics and contaminant concentrations (Cu,Cd, PCBs and PBDEs) as environmental quality of water and sediment

Environmental characteristics in water and sediments of two contrasted coastal Mediterranean lagoons, Bages-Sigean and Canet-St Nazaire, were measured over a three season survey. The urban pollution (treatment plant discharges) is very important in Canet-St Nazaire lagoon reflecting untreated sewages, while in Bages-Sigean, the northern part appears more impacted due to larger anthropogenic inputs. Dissolved Cd concentrations are on the whole similar in both lagoons, whereas Cu concentrations are by far higher in lagoon Canet-St Nazaire. Cu concentrations appear to be highly dependent on dissolved organic carbon whereas salinity seems to control Cd variations. Concerning the sediments, the confined northern part of lagoon Bages-Sigean shows organic carbon and total nitrogen enrichment whereas lipid concentrations are much higher in the Canet-St Nazaire lagoon. Cu complexation seems to be strongly related to organic matter as evidenced by the two significant positive relationships, on one hand between Cu and organic carbon, and on the other hand, between Cu and lipids. On the contrary, Cd concentrations appear to be mainly controlled by carbonates. PCBs and PBDEs were detected only in sediments and show relatively low concentrations compared to similar lagoon environments. Regarding the sediment quality guidelines, Cd, Cu and PCBs in both lagoons did not exceed any Probable Effect Concentration (PEC).     

Solubilization of municipal sewage waste activated sludge by novel lytic bacterial strains

Extracellular polymeric substances (EPS) are an extracellular matrix found in sludge which plays a crucial role in flocculation by interacting with the organic solids. Therefore, to enhance pretreatment of sludge, EPS have to be removed. In this study, EPS were removed with a chemical extractant, NaOH, to enhance the bacterial pretreatment. A lysozyme secreting bacterial consortium was isolated from the waste activated sludge (WAS). The result of density gradient gel electrophoresis (DGGE) analysis revealed that the isolated consortium consists of two strains. The two novel strains isolated were named as Jerish03 (NCBI accession number KC597266) and Jerish 04 (NCBI accession number KC597267) and they belong to the genus Bacillus. Pretreatment with these novel strains enhances the efficiency of the aerobic digestion of sludge. Sludge treated with the lysozyme secreting bacterial consortium produced 29 % and 28.5 % increase in suspended solids (SS) reduction and chemical oxygen demand (COD) removal compared to the raw activated sludge (without pretreatment) during aerobic digestion. It is specified that these two novel strains had a high potential to enhance WAS degradation efficiency in aerobic digestion.     

Photocatalytic degradation of acetaminophen in modified TiO2 under visible irradiation

This study investigated the photocatalytic degradation of acetaminophen (ACT) in synthetic titanium dioxide (TiO₂) solution under a visible light (λ >440 nm). The TiO₂ photocatalyst used in this study was synthesized via sol–gel method and doped with potassium aluminum sulfate (KAl(SO₄)₂) and sodium aluminate (NaAlO₂). The influence of some parameters on the degradation of acetaminophen was examined, such as initial pH, photocatalyst dosage, and initial ACT concentration. The optimal operational conditions were also determined. Results showed that synthetic TiO₂ catalysts presented mainly as anatase phase and no rutile phase was observed. The results of photocatalytic degradation showed that LED alone degraded negligible amount of ACT but with the presence of TiO₂/KAl(SO₄)₂, 95 % removal of 0.10-mM acetaminophen in 540-min irradiation time was achieved. The synthetic TiO₂/KAl(SO₄)₂ presented better photocatalytic degradation of acetaminophen than commercially available Degussa P-25. The weak crystallinity of synthesized TiO₂/NaAlO₂ photocatalyst showed low photocatalytic degradation than TiO₂/KAl(SO₄)₂. The optimal operational conditions were obtained in pH 6.9 with a dose of 1.0 g/L TiO₂/KAl(SO₄)₂ at 30 °C. Kinetic study illustrated that photocatalytic degradation of acetaminophen fits well in the pseudo-first order model. Competitive reactions from intermediates affected the degradation rate of ACT, and were more obvious as the initial ACT concentration increased.