Analysis of PV module connected in different configurations under uniform and non-uniform solar radiations

This paper focuses on investigating the current--voltage (I--V) and power--voltage (P--V) characteristics of a photovoltaic (PV) module connected in various configurations like series, parallel, and series-parallel. The performance analysis of PV module has been carried out under uniform and non-uniform conditions such as change in irradiation (passing clouds), change in temperature, accumulation of dust, and change in wind speed using MATLAB-Simulink environment. From the observed results, it has been indicated that for a given number of PV modules, the array configurations affect the maximum available output power and more local maxima are found under partially shaded conditions. Moreover, the comparative analysis of PV module has been performed for various configurations under the above disturbances. From the results, it is evident that even under non-uniform conditions, the parallel configuration of PV modules is more prominent and maximum output power is obtained. Further, parallel layout is particularly convenient for minimizing shadowing effects. The parameters of the PV module have been obtained from the manufacturer datasheet (KC200GT) for these investigations.     

DNAPL Source Depletion: 2. Attainable Goals and Cost–Benefit Analyses

It is difficult to quantify the range in source strength reduction (MdR) that may be attainable from in situ remediation of a dense nonaqueous‐phase liquid (DNAPL) site given that available studies typically report only the median MdR without providing insights into site complexity, which is often a governing factor. An empirical study of the performance of in situ remediation at a wide range of DNAPL‐contaminated sites determined MdRs for in situ bioremediation (EISB), in situ chemical oxidation (ISCO), and thermal treatment remedies. Median MdR, geometric mean MdR, and lower/upper 95 percent confidence interval for the mean were: 49x, 105x, 20x/556x, respectively, for EISB; 9x, 21x, and 4x/110x for ISCO; and 19x, 31x, and 6x/150x for thermal treatment. Lower MdR values were determined for large, complex sites and for sites with DNAPL pool‐dominated source zones. A feasibility analysis of partial DNAPL depletion is described for a pool‐dominated source zone. Back‐diffusion from low‐hydraulic conductivity units within a pool‐dominated source zone is shown to potentially sustain a secondary source for more than 1,000 years, indicating that aggressive source treatment may not reduce the remediation timeframe. Estimated plume response demonstrates there may be no reduction in cost associated with aggressive treatment, and little difference in risk reduction associated with the various alternatives. Monitored natural attenuation (MNA) for the source zone is shown to be a reasonable alternative for the pool‐dominated source zone considered in this example. It is demonstrated that pool‐dominated source zones with a large range in initial DNAPL mass (250 to 1,500 kg) may correspond to a narrow range in source strength (20 to 30 kg/year). This demonstrates that measured source strength is nonunique with respect to DNAPL mass in the subsurface and, thus, source strength should not be used as the sole basis for predicting how much DNAPL mass remains or must be removed to achieve a target goal. If aggressive source zone treatment is to be implemented due to regulatory requirements, strategic pump‐and‐treat is shown to be most cost effective. These remedial decisions are shown to be insensitive to a range of possible DNAPL pool conditions. At sites with an existing pump‐and‐treat system, a significant increase in mass removal and source strength reduction may be achieved for a low incremental cost by strategic placement of extraction wells and pumping rate selection. © 2014 Wiley Periodicals, Inc.     

How do soil and water conservation practices influence climate change impacts on potato production? Evidence from eastern Canada

We used a stochastic production function method together with a farm-level dataset covering 18 farms over a 23-year period to assess the role that soil and water conservation practices play in affecting the climate change impacts on potato yield in northwestern New Brunswick, Canada. Our analysis accounted for the yield effects of farm inputs, farm technologies, farm-specific factors, seasonal climatic variables, soil and water conservation practices, and a series of interaction terms between soil and water conservation practices and climatic variables. Regression results were used in combination with three climate change scenarios developed by the Intergovernmental Panel on Climate Change (A2, A1B, B1) and four general circulation model predictions over three 30-year time periods (2011–2040, 2041–2070, and 2071–2100) to estimate a range of potato yield projections over these time periods. Results show that accounting for soil and water conservation practices in climate–yield relationships increased the impacts of climate change on potato yield, with yield increases of up to 38 % by the 2071–2100 period. These findings provide evidence that adoption of soil and water conservation practices can help boost potato production in a changing Canadian climate.     

Duo-molecularly imprinted polymer-coated magnetic particles for class-selective removal of endocrine-disrupting compounds from aqueous environment

The removal of steroid and phenolic endocrine-disrupting compounds (EDCs) from an aqueous environment was investigated using magnetic particles encapsulated by a duo-molecularly imprinted polymer (duo-MIP). The effect of environmental variables on the binding efficiency was studied. Experimental results showed that the amount of EDCs adsorbed was neither affected by up to 10.0 mM NaCl nor significantly interfered by up to 10.0 mg/L humic acid. Negligible influence was observed from pH 3.3 to pH 6.8, but a decrease started at pH 9. Freundlich isotherm parameters indicated binding capacities in the order of DES?>?E2?～?E1?>?BPA. The applicability of class-selective removal was verified using river water samples spiked with these EDCs at 10 μg/L; the binding efficiencies were 90, 90, 88, and 98 % for estrone (E1), 17β-estradiol (E2), bisphenol A (BPA), and diethylstilbestrol (DES), respectively. A reuse investigation verified constant binding capacities exhibiting <2 % reduction after seven cycles of regeneration.     

Emissions from Burning Grass Stubble and Straw

The emissions from burning the residue following grass-seed harvest were determined by means of a combined laboratory-field study. Samples of the straw and stubble residue were burned in the laboratory burning tower at the University of California at Riverside. Complete analyses were determined for gaseous and particulate emissions for the important grass species from the Willamette Valley of Oregon. Particulate emissions averaged 15.6 lb/ton of fuel burned. Carbon monoxide averaged 101 lb/ton of fuel burned. Hydrocarbon emission averages, in pounds per ton of fuel burned, were 1.74 for saturates plus acetylene, 2.80 for defines, and 1.68 for ethylene. The NO_x emission, at the temperature peak during the burn, averaged 29.3 ppm. Field studies, conducted by personnel from Oregon State University, measured only particulate emissions, carbon dioxide, and temperature over the burn. The carbon dioxide values were found to be similar to those obtained on the burning table at UCR and it was therefore concluded that the other gaseous emissions were similar and could be used as reasonably accurate for emission inventories. The temperature values obtained in the laboratory and field were also similar and further justifies extrapolating the burning table data to field situations. The particulate matter collected in the field studies averaged 15.55 lb of particulate per ton of fuel burned. This is the same average obtained for the burning table data which again serves to validate the emissions reported from Riverside. Much more variability was found in the particulate emissions obtained in the field which reflects the wider range of environmental conditions encountered in the field.     

Coke Oven Pushing Emission Control System

This report deals with the entrapment, pickup, and transfer of hot gases during a typical coke oven push. Background information that led to the development of the Great Lakes Coke Oven Pushing Emission Control System is presented along with the problems that were encountered and solved during the design, construction, installation, and start-up of a pilot plant entrapment structure on a battery of 40 Simon Carves coke ovens. This unique entrapment structure has operated successfully since April 1972, and has been visited by representatives from almost all coke manufacturers in the U.S., as well as interested groups from several foreign countries. In addition to these operation groups, we have been visited by various state and federal pollution authorities, such as the Environmental Protection Agency, Battelle Institute, and National Institute of Occupational Safety and Health. At the present time we are erecting a similar entrapment structure on the north side of our plant, comprising 18 Koppers and 35 Wilputte ovens.     

Continuous Emission Monitoring: Objectives and Requirements

Regulations were recently proposed by the Environmental Protection Agency which, when promulgated, will require existing and new sources within certain specified source categories to install, operate, and maintain continuous emission monitoring systems. Major comments received on these proposed regulations are discussed as are the overall benefits that can be derived from the utilization of continuous emission monitoring systems.     

Simplified Models of U.S. Acid Rain Control Costs

Simplified algorithms are presented for estimating the cost of controlling sulfur dioxide (SO₂) emissions from existing coal-fired power plants on a state-by-state basis. Results are obtained using the detailed Utility Control Strategy Model (UCSM) to calculate the Impacts of emission reductions ranging from approximately 30 percent to 90 percent of projected 1995 emissions for 18 different scenarios and 36 states. Scenarios include the use of two dry SO₂ removal technologies (lime spray dryers and LIMB) as potential options for power plant retrofit, in addition to currently available emission control options including coal switching, coal cleaning and wet flue gas desulfurization (FGD). Technical assumptions relating to FGD system performance and the upgrading of existing cold-side electrostatic precipitators (ESP) for reduced sulfur levels are also analyzed, along with the effects of interest rates, coal prices, coal choice restrictions, plant lifetime, and plant operating levels. Results are summarized in the form of a 3-term polynomial equation for each state, giving total annualized SO₂ control cost as a function of the total SO₂ emissions reduction for each scenario. Excellent statistical fits to UCSM results are obtained for these generalized equations.