This study evaluated the individual and interactive effect of phenol and thiocyanate (SCN−) on partial nitritation (PN) activity using batch test and response surface methodology. The IC50 of phenol and SCN− on PN sludge were 5.6 and 351 mg L−1, respectively. The PN sludge was insensitive to phenol and SCN− at levels lower than 1.77 and 43.3 mg L−1, respectively. A regression model equation was developed and validated to predict the relative specific respiration rate (RSRR) of PN sludge exposed to different phenol and SCN− concentrations. In the range of independent variables, the most severe inhibition was observed with a valley value (17%) for RSRR, when the phenol and SCN− concentrations were 4.08 and 198 mg L−1, respectively. An isobole plot was used to judge the combined toxicity of phenol and SCN−, and the joint inhibitory effect was variable depending on the composition and concentration of the toxic components. Furthermore, the toxic compounds showed independent effects, which is the most common type of combined toxicity.
Environmental Science and Pollution Research - Water-saving cultivation techniques have been attracting increased attention worldwide. Ridge-furrow mulching system (RFMS), as a prospective... 相似文献
A wide range of waste biomass/waste wood feedstocks abundantly available at mine sites provide the opportunity to produce biochars for cost-effective improvement of mine tailings and contaminated land at metal mines. In the present study, soft- and hardwood biochars derived from pine and jarrah woods at high temperature (700 °C) were characterized for their physiochemical properties including chemical components, electrical conductivity, pH, zeta potential, cation-exchange capacity (CEC), alkalinity, BET surface area and surface morphology. Evaluating and comparing these characteristics with available data from the literature have affirmed the strong dictation of precursor type on the physiochemical properties of the biochars. The pine and jarrah wood feedstocks are mainly different in their proportions of cellulose, hemicellulose and lignin, resulting in biochars with heterogeneous physiochemical properties. The hardwood jarrah biochar exhibits much higher microporosity, alkalinity and electrostatic capacity than the softwood pine. Correlation analysis and principal component analysis also show a good correlation between CEC–BET–alkalinity, and alkalinity–ash content. These comprehensive characterization and analysis results on biochars’ properties from feedstocks of hardwood (from forest land clearance at mine construction) and waste pine wood (from mining operations) will provide a good guide for tailoring biochar functionalities for remediating metal mine tailings. The relatively inert high-temperature biochars can be stored for a long term at mine closure after decades of operations. 相似文献
Based on the China high resolution emission gridded data (1 km spatial resolution), this article is aimed to create a Chinese city carbon dioxide (CO2) emission data set using consolidated data sources as well as normalized and standardized data processing methods. Standard methods were used to calculate city CO2 emissions, including scope 1 and scope 2. Cities with higher CO2 emissions are mostly in north, northeast, and eastern coastal areas. Cities with lower CO2 emissions are in the western region. Cites with higher CO2 emissions are clustered in the Jing-Jin-Ji Region (such as Beijing, Tianjin, and Tangshan), and the Yangtze River Delta region (such as Shanghai and Suzhou). The city per capita CO2 emission is larger in the north than the south. There are obvious aggregations of cities with high per capita CO2 emission in the north. Four cities among the top 10 per capita emissions (Erdos, Wuhai, Shizuishan, and Yinchuan) cluster in the main coal production areas of northern China. This indicates the significant impact of coal resources endowment on city industry and CO2 emissions. The majority (77%) of cities have annual CO2 emissions below 50 million tons. The mean annual emission, among all cities, is 37 million tons. Emissions from service-based cities, which include the smallest number of cities, are the highest. Industrial cities are the largest category and the emission distribution from these cities is close to the normal distribution. Emissions and degree of dispersion, in the other cities (excluding industrial cities and service-based cities), are in the lowest level. Per capita CO2 emissions in these cities are generally below 20 t/person (89%) with a mean value of 11 t/person. The distribution interval of per capita CO2 emission within industrial cities is the largest among the three city categories. This indicates greater differences among per capita CO2 emissions of industrial cities. The distribution interval of per capita CO2 emission of other cities is the lowest, indicating smaller differences of per capita CO2 emissions among this city category. Three policy suggestions are proposed: first, city CO2 emission inventory data in China should be increased, especially for prefecture level cities. Second, city responsibility for emission reduction, and partitioning the national goal should be established, using a bottom-up approach based on specific CO2 emission levels and potential for emission reductions in each city. Third, comparative and benchmarking research on city CO2 emissions should be conducted, and a Top Runner system of city CO2 emission reduction should be established. 相似文献
In view of the Brazilian Ten‐Year Energy Expansion Plan 2021, this article presents a discussion on environmental flow (e‐flow). The authors analyze the literature to show the evolution of publications concerning e‐flow releases from the perspective of ecosystems services preservation considering results from different case studies from throughout the world. Finally, two main recommendations are drawn regarding e‐flow are: (1) performing a holistic approach to e‐flow planning, including hydrological, hydraulic, water quality, habitat, and riparian zone considerations; and (2) installing in new structures adequate bottom outlets to allow a range of adjustable e‐flow from reservoir dams to reproduce natural flow variations. 相似文献
This paper aims to reveal the heat transfer mechanism of low-temperature phase change material (PCM) and design PCM heat storage device in building heating environment. Firstly, low-temperature binary PCMs of lauric acid and stearic acid are prepared, and their thermal properties are investigated by DSC. Then, shell and tube latent heat thermal energy storage units are conducted, and heat transfer experiments are carried out to analyze the heat transfer mechanism of PCM. The results demonstrate that natural convection plays an important role in heat transfer process, and the heat storage efficiency of PCMs can be significantly enhanced by increasing the fin width and improving the inlet heat transfer fluid (HTF) temperature. Furthermore, some proposals are put forward to guide the design of PCM storage device in building heating environment. 相似文献
A fused silica capillary reactor combined with a heating/cooling stage, a microscope and a digital camera were used to investigate phase behavior during the hydrothermal liquefaction of microalgae (Dunaliella tertiolecta) and model compounds, including soya protein and glycine, starch, glucose and xylose, stearic acid and palmitic acid. Bubbles were generated at 246°C and disappeared at 360°C upon heating when Dunaliella tertiolecta used as feedstocks. Moreover, liquid products were generated at 300°C upon heating and oily liquid products began to separate out at 250°C upon cooling. The phase behavior of soya protein was similar to that of the Dunaliella tertiolecta. Meanwhile, there only observed the bubbles generation during hydrothermal liquefaction of glycine. Heating the starch, glucose and xylose above 350°C generated black solids from carbonization. Stearic acid and palmitic acid only had the process of melting, dissolution, dispersion and precipitation. 相似文献
In a proton exchange membrane electrolyzer cell (PEMEC), liquid/gas diffusion layer (LGDL) is expected to transport electrons, heat, and reactants/products to and from the catalyst layer with minimum voltage, current, thermal, interfacial, and fluidic losses. In addition, carbon materials, which are typically used in PEM fuel cells (PEMFCs), are unsuitable in PEMECs due to the high ohmic potential and highly oxidative environment of the oxygen electrode. In this study, a set of titanium gas diffusion layers with different thicknesses and porosities are designed and examined coupled with the development of a robust titanium bipolar plate. It has been found that the performance of electrolyzer improves along with a decrease in thickness or porosity of the anode LGDL of titanium woven meshes. The ohmic resistance of anode LGDL and contact resistance between anode LGDL and the anode catalyst play dominant roles in electrolyzer performance, and better performance can be obtained by reducing ohmic resistance. Thin titanium LGDLs with straight-through pores and optimal pore morphologies are recommended for the future developments of low-cost LGDLs with minimum ohmic/transport losses. 相似文献