Controlled Enrichment System for Experimental Fumigation of Plants in the Field with Sulfur Dioxide

A prototype Free-Air Controlled Enrichment (FACE) system was developed at Brookhaven National "Laboratory (BNL) for the experimental control of gas concentrations in an open field, without any form of enclosure. This FACE system consists of a toroidal plenum chamber, 15 m in diameter, with a series of 32 vertical vent pipes from which the release of a test gas can be controlled. Data on gas concentration at the center of the array and wind velocity are fed to a microprocessor where a proportional, integrative, differential (PID) algorithm is used to regulate a mass-flow controller. Data on wind direction are used to control the opening and closing of the vertical vent pipes to maintain an upwind release. In 72 hours of continuous operation during which wind velocity varied between 0.3 to 8 m sec^-1, the FACE prototype maintained 1 -min averaged concentrations within twenty percent of the 40 ppb set point 94 percent of the time.     

Flow Injection Analysis of MWC Fly Ash Leaching Characteristics

Abstract

A completely mixed batch reactor leaching method utilizing flow injection analysis (the CMBR-FIA method) was developed to study the lead leaching characteristics of municipal waste combustor fly ash. Flow injection analysis (FIA) coupled with atomic absorption spectrophotometry enabled the determination of lead concentrations at one minute intervals. The pH and oxidation-reduction potential of the solution were continuously monitored to characterize the leaching conditions. Automatic titration was used to alter the solution pH to defined endpoints. The CMBR-FIA method offers the ability to immediately observe alterations to the leaching solution, and grants the freedom to study a number of parameters concurrently. The CMBR-FIA method is a rapid and reliable means to investigate leaching characteristics. This paper describes the method and demonstrates its use to monitor the leaching of lead from municipal solid waste combustor fly ash as a function of pH. Soluble lead concentrations are shown to increase quickly with decreasing pH.

A maximum of 50% of the total lead concentration was available in solution at pH 2. This value gradually decreased with time to over 35% of the total.     

Receptor Model Evaluation of the Southeast Michigan Ozone Study Ambient NMOC Measurements

Abstract

Large-scale studies like the Southeast Michigan Ozone Study (SEMOS) have focused attention on quantifying and spedating inventories for volatile organic compounds (VOCs). One approach for evaluating the accuracy of a VOC emission inventory is the development of a chemical mass balance (CMB) receptor model for ambient non-methane organic compound (NMOC) measurements. CMB evaluations of ambient hydrocarbon data provide a sample-specific allocation of emissions to individual source categories. This study summarizes the results of an application of the CMB model to the NMOC data from the SEMOS study. Comparison of CMB results with emission inventory values for the Detroit area show that vehicle emissions are well represented by the inventory, as are architectural coatings and coke ovens. Estimated emissions from petroleum refineries and graphic arts industries are much lower in the inventory than determined from the receptor allocation. Under-reporting of fugitive VOC emissions from petroleum refineries is an ongoing problem. Emissions from graphic arts industries are underestimated in the inventory partly because of the broad characterization of the emission factor (i.e., mass emitted/capita), which may be less useful when specific locations and days are under consideration. This study also demonstrates the effectiveness of the CMB approach when used prospectively to track the implementation of emission control strategies. While vehicle emission concentrations were unchanged from 1988 to 1993, measurement-based CMB results suggest a decrease in evaporative emissions during this time period resulting from Reid vapor pressure (RVP) reductions (from 11.0 psi in 1988 to 8.6 psi in 1993) and fleet turnover. Changes in emissions from coke plants and petroleum refineries were also seen in the CMB allocations for these sources.     

Method Comparisons for Particulate Nitrate,Elemental Carbon,and PM2.5 Mass in Seven U.S. Cities

ABSTRACT

Methods that measure PM₂₅ mass, total particulate NO₃ ^-, and elemental carbon (EC) were evaluated in seven U.S. cities from 1997 to 1999. Sampling was performed in Bakersfield, CA; Boston, MA; Chicago, IL; Dallas, TX; Philadelphia, PA; Phoenix, AZ; and Riverside, CA. Evaluating and validating methods that measure the components of fine mass are important to the effort of establishing a speciation-monitoring network. The Harvard Impactor (HI), which measures fine particle mass, showed excellent agreement (r² = 0.99) with the PM₂₅ Federal Reference Method (FRM) for 81 24-hr samples in Riverside and Bakersfield. The HI also showed good precision (4.8%) for 243 24-hr collocated samples over eight studies.

The Aethalometer was employed in six of the sampling locations to measure black carbon (BC). These values were compared to EC as measured from a quartz filter using thermal analysis. For the six cities combined, the two methods were highly correlated (r² = 0.94; 187 24-hr samples); however, the BC values were approximately 24% less than the EC measurements consistently across all six cites. This compares well to results observed for EC/BC measurements observed in other semi-urban areas. Par-ticulate NO₃ ^- was measured using the Harvard-EPA Annular Denuder System (HEADS). This was compared to the NO₃ ^- measured from the HI Teflon (DuPont) filter to assess NO₃ ^- artifacts. Significant NO₃ ^- losses (approximately 50% of total NO₃ ^-) were found in Riverside, Philadelphia, and Boston, while minimal artifacts were observed in the other sites. Two types of HEADS configurations were employed in five cities. One system used a Na₂CO₃-coated glass fiber filter, and the other type used a nylon filter to collect volatilized NO₃ ^- from the Teflon filter. The HEADS with the Na₂CO₃-coated filter consistently underestimated the total particulate NO₃ ^- by approximately 20% compared to the nylon HEADS.     

Laboratory and Field Evaluation of Measurement Methods for One-Hour Exposures to O3, PM25, and CO

ABSTRACT

While researchers have linked acute (less than 12-hr) ambient O₃, PM₂₅, and CO concentrations to a variety of adverse health effects, few studies have characterized short-term exposures to these air pollutants, in part due to the lack of sensitive, accurate, and precise sampling technologies. In this paper, we present results from the laboratory and field evaluation of several new (or modified) samplers used in the “roll-around” system (RAS), which was developed to measure 1-hr O₃, PM₂₅, and CO exposures simultaneously. All the field evaluation data were collected during two sampling seasons: the summer of 1998 and the winter of 1999.

To measure 1-hr O₃ exposures, a new active O₃ sampler was developed that uses two nitrite-coated filters to measure O₃ concentrations. Laboratory chamber tests found that the active O₃ sampler performed extremely well, with a collection efficiency of 0.96 that did not vary with temperature or relative humidity (RH). In field collocation comparisons with a reference UV photometric monitor, the active O₃ sampler had an effective collection efficiency ranging between 0.92 and 0.96 and a precision for 1-hr measurements ranging between 4 and 6 parts per billion (ppb). The limits of detection (LOD) of this method were 9 ppb-hr for the chamber tests and ~16 ppb-hr for the field comparison tests.

PM_2.5 and CO concentrations were measured using modified continuous monitors—the DustTrak and the Langan, respectively. A size-selective inlet and a Nafion dryer were placed upstream of the DustTrak inlet to remove particles with aerodynamic diameters greater than 2.5 um and to dry particles prior to the measurements, respectively. During the field validation tests, the DustTrak consistently reported higher PM_2.5 concentrations than those obtained by the collocated 12-hr PM_{2 5} PEM samples, by approximately a factor of 2. After the DustTrak response was corrected (correction factor of 2.07 in the summer and 2.02 in the winter), measurements obtained using these methods agreed well with R² values of 0.87 in the summer and 0.81 in the winter. The results showed that the DustTrak can be used along with integrated measurements to measure the temporal and spatial variation in PM_{2 5} exposures. Finally, during the field validation tests, CO concentrations measured using the Langan were strongly correlated with those obtained using the reference method when the CO levels were above the LOD of the instrument [~1 part per million (ppm)].     

Weekday/Weekend Ozone Differences: What Can We Learn from Them?

Abstract

A national analysis of weekday/weekend ozone (O₃) differences demonstrates significant variation across the country. Weekend 1-hr or 8-hr maximum O₃ varies from 15% lower than weekday levels to 30% higher. The weekend O₃ increases are primarily found in and around large coastal cities in California and large cities in the Midwest and Northeast Corridor. Both the average and the 95th percentile of the daily 1-hr and 8-hr maxima exhibit the same general pattern. Many sites that have elevated O₃ also have higher O₃ on weekends even though traffic and O₃ precursor levels are substantially reduced on weekends. Detailed studies of this phenomenon indicate that the primary cause of the higher O₃ on weekends is the reduction in oxides of nitrogen (NO_x) emissions on weekends in a volatile organic compound (VOC)-limited chemical regime. In contrast, the lower O₃ on weekends in other locations is probably a result of NO_x reductions in a NO_x-limited regime. The NO_x reduction explanation is supported by a wide range of ambient analyses and several photochemical modeling studies. Changes in the timing and location of emissions and meteorological factors play smaller roles in weekend O₃ behavior. Weekday/weekend temperature differences do not explain the weekend effect but may modify it.     

Development of Emission Factors for Polycarbonate Processing

Abstract

Emission factors for selected volatile organic compounds (VOCs) and particulate emissions were developed while processing eight commercial grades of polycarbonate (PC) and one grade of a PC/acrylonitrile-butadiene-styrene (ABS) blend. A small commercial-type extruder was used, and the extrusion temperature was held constant at 304 °C. An emission factor was calculated for each substance measured and is reported as pounds released to the atmosphere/million pounds of polymer resin processed [ppm (wt/wt)]. Scaled to production volumes, these emission factors can be used by processors to estimate emission quantities from similar PC processing operations.     

Terrestrial exposure of oilfield flowline additives diminish soil structural stability and remediative microbial function

Onshore oil production pipelines are major installations in the petroleum industry, stretching many thousands of kilometres worldwide which also contain flowline additives. The current study focuses on the effect of the flowline additives on soil physico-chemical and biological properties and quantified the impact using resilience and resistance indices. Our findings are the first to highlight deleterious effect of flowline additives by altering some fundamental soil properties, including a complete loss of structural integrity of the impacted soil and a reduced capacity to degrade hydrocarbons mainly due to: (i) phosphonate salts (in scale inhibitor) prevented accumulation of scale in pipelines but also disrupted soil physical structure; (ii) glutaraldehyde (in biocides) which repressed microbial activity in the pipeline and reduced hydrocarbon degradation in soil upon environmental exposure; (iii) the combinatory effects of these two chemicals synergistically caused severe soil structural collapse and disruption of microbial degradation of petroleum hydrocarbons.     

Larvicidal and pupicidal activities of eco-friendly phenolic lipid products from Anacardium occidentale nutshell against arbovirus vectors

Environmental Science and Pollution Research - Aedes aegypti and Culex quinquefasciatus are vectors of diseases that constitute public health problems. The discovery of products capable of...     

Changes in Streambed Composition in Salmonid Spawning Habitat of the Elwha River during Dam Removal

One uncertainty associated with large dam removal is the level of downstream sediment deposition and associated short‐term biological effects, particularly on salmonid spawning habitat. Recent studies report downstream sediment deposition following dam removal is influenced by proximity to the source and river transport capacity. The impacts of dam removal sediment releases are difficult to generalize due to the relatively small number of dam removals completed, the variation in release strategies, and the physical nature of systems. Changes to sediment deposition and associated streambed composition in the Elwha River, Washington State, were monitored prior to (2010‐2011) and during (2012‐2014) the simultaneous removal of two large dams (32 and 64 m). Changes in the surface layer substrate composition during dam removal varied by year and channel type. Riffles in floodplain channels downstream of the dams fined and remained sand dominated throughout the study period, and exceeded levels known to be detrimental to incubating salmonids. Mainstem riffles tended to fine to gravel, but appear to be trending toward cobble after the majority of the sediment was released and transported through system. Thus, salmonid spawning habitats in the mainstem appear to have been minimally impacted while those in floodplain channels appear to have been severely impacted during dam removal.