Metal concentrations in used engine oils: Relevance to site assessments of soils

Used engine oils contain metals, which upon entering soils may pose risks to human health or the environment. In this study, previously published concentrations of 23 metals in 213 used engine oil samples from the early 1970s to the mid-1990s are statistically evaluated. Neat (100%) used engine oils were found to contain relatively high concentrations of lead, calcium, and zinc, attributable to piston blow-by of leaded gasoline, calcium salt detergent additives, and zinc-bearing anti-corrosion/anti-oxidation additives, respectively. Wear metal concentrations were lower. The lead concentration in used engine oils in the U.S. declined between the 1970s and early 1990s, potentially providing a basis to constrain the “age” of used engine oil(s) in soils. The concentrations of 23 metals in used engine oils were compared to soil risk benchmarks in 15 representative jurisdictions in the U.S., Canada, Australia, and Europe. The maximum concentrations in neat (100%) used engine oil of eight metals – Be, Co, Fe, Mn, Ni, Se, Ag, and Ti – were lower than their collective minimum benchmarks in soils for the jurisdictions surveyed, indicating their concentrations in soils could not be reasonably expected to exceed any soil benchmarks. Nine metals (As, Ba, Cd, Cr, Cu, Pb, Sn, V and Zn), but particularly arsenic, cadmium, lead, tin, and zinc, were identified as potential contaminants of concern (PCOC) for soils from locations impacted with used engine oils, owing to their higher median concentrations (i.e., 2.5, 1.4, 1038, 5.0, and 922 mg/kg in oil, respectively) relative to most soil benchmarks. Site-specific benchmarks and metal concentrations at reasonable oil in soil concentrations require consideration when developing the suite of PCOC metal analytes for conducting site assessments of soils impacted by used engine oil.     

Carbon and nitrogen mineralization in Vertisol as mediated by type and placement method of residue

Selection of appropriate residue application method is essential for better use of biomass for soil and environmental health improvement. A laboratory incubation experiment was conducted for 75 days to investigate C and N mineralization of residues of soybean (Glycine max L.), chickpea (Cicer arietinum L.), maize (Zea mays L.), and wheat (Triticum aestivum L.) placed on the soil surface and incorporated into the soil. The residue of soybean and chickpea had a greater decomposition rate than that of maize and wheat, despite of their placements. Higher rate of decomposition of the residue of soybean and chickpea was recorded when it was kept on the soil surface while soil incorporation of residue of wheat and maize resulted in faster decomposition. Therefore, these findings could be used as guidelines for management of crop residue application in farmland to improve soil and environmental quality.     

Treatment technologies for PAH-contaminated sites: a critical review

To reduce environmental and human health risks of contaminated sites, having a comprehensive knowledge about the polycyclic aromatic hydrocarbon (PAH) removal processes is crucial. PAHs are contaminants which are highly recognized to pose threats to humans, animals, and plants. PAHs are hydrophobic and own two or more benzene rings, and hence are resistant to structural degradation. There are various techniques which have been developed to treat PAH-contaminated soil. Four distinct processes to remove PAHs in the contaminated soil, thought to be more effective techniques, are presented in this review: soil washing, chemical oxidation, electrokinetic, phytoremediation. In a surfactant-aided washing process, a removal rate of 90% was reported. Compost-amended phytoremediation treatment presented 58–99% removal of pyrene from the soil in 90 days. Chemical oxidation method was able to reach complete conversion for some PAHs. In electrokinetic treatment, researchers have achieved reliable results in removal of some specific PAHs. Researchers’ innovations in novel studies and advantages/disadvantages of the techniques are also investigated throughout the paper. Finally, it should be noted that an exclusive method or a combination of methods by themselves are not the key to be employed for remediation of every contaminated site but the field characteristics are also essential in selection of the most appropriate decontamination technique(s). The remedy for selection criteria is based on PAH concentrations, site characteristics, costs, shortcomings, and advantages.     

Reservoir water quality: a case from Jordan

Jordan relies heavily on reservoirs building and development to cope with water supply challenges, where monitoring and assessment of reservoir water quality are critically important for the sustainable use of these water supplies. Mujib Dam is an important water supply source in central western Jordan. Evaluation of water quality parameters and their spatial distributions (vertical and horizontal) showed near-neutral pH values with nearly similar values from surface to bottom. The vertical profile of DO and TDS in the dammed reservoir showed slight decreasing trends with increasing depth. Although Ca, Mg, Na, and K concentrations varied slightly with depths, their variations showed no trends. Similarly, the vertical and horizontal distribution patterns of Cl, SO₄, HCO₃, NO₃, and PO₄ in Mujib reservoir water showed insignificant variations in surface water layer and relatively unchanged values or decreasing trends through the water column. Higher values of TN have been observed, especially in the western part, suggesting that agricultural activities and livestock farming in the upstream catchment are impacting water quality. Results revealed that weathering and dissolution of rocks are the major source of water chemistry. The majority of trace metal levels (Cd, Cr, Cu, Fe, Mn, Pb, Zn, Co, Ni, Sr, and B) in water showed relatively similar surface and bottom values. The concentrations of COD and BOD₅ in surface water were relatively low with higher concentrations observed in the northwestern corner, coincided with higher levels of chlorophyll a. The average ratio of TN to TP in surface water suggests that phosphorus is the limiting factor for the algal blooms, whereas the average chlorophyll a level in surface water indicates oligo-mesotrophic water.     

Seasonal and diurnal measurements of carbon monoxide and nonmethane hydrocarbons at Mt. Wilson,California: Indirect evidence of atomic Cl in the Los Angeles basin

We present a study of the seasonal and diurnal variability of carbon monoxide and selected volatile organic compounds in the Los Angeles area. Measurements were made during four different nine-day field campaigns in April/May, September, and November, 2007, and February, 2008, at the Mt. Wilson sampling site, which is located at an elevation of approximately 1700 m in the San Gabriel Mountains overlooking Pasadena and the Los Angeles basin. The results were used to characterize the Mt. Wilson site as a representative location for monitoring integrated Los Angeles basin emissions, and, by reference to carbon monoxide emissions, to estimate average annual emissions. The considerable seasonal variability of many hydrocarbons, in both their measured mixing ratios and their relationship to carbon monoxide, was indicative of variable source strengths. Most interestingly, perturbation of C₄ hydrocarbon ratios suggested an enhanced role for chlorine chemistry during the month of September, likely as the result of Los Angeles’ coastal location. Such coastal influence was confirmed by observations of enhanced mixing ratios of marine halocarbons, as well as air mass back trajectories.     

Urban tracer dispersion experiments during the second DAPPLE field campaign in London 2004

As part of the DAPPLE programme two large scale urban tracer experiments using multiple simultaneous releases of cyclic perfluoroalkanes from fixed location point sources was performed. The receptor concentrations along with relevant meteorological parameters measured are compared with a three screening dispersion models in order to best predict the decay of pollution sources with respect to distance. It is shown here that the simple dispersion models tested here can provide a reasonable upper bound estimate of the maximum concentrations measured with an empirical model derived from field observations and wind tunnel studies providing the best estimate. An indoor receptor was also used to assess indoor concentrations and their pertinence to commonly used evacuation procedures.     

Verification of diffusive and pumped samplers for volatile organic compounds using a controlled atmosphere test facility

There is a requirement to verify the performance of sorbent-based passive or active samplers and to extend their use, where possible, to monitor volatile organic compounds (VOCs) that are known to be photochemical ozone pre-cursors or are relevant to the activities of the petrochemical industry. We report measurements of the 14-day diffusive uptake rates for the VOCs: i-butane (2-methyl propane), n-butane, i-pentane (2-methyl butane), n-pentane, n-hexane, benzene, toluene, and m-xylene (at environmental level concentrations) for industry standard axial samplers (Perkin–Elmer-type samplers) containing the sorbents Carbopack-X, -Z, -B or Tenax-TA. We also present data on back-diffusion, blank levels, and storage for the above sorbents, and describe the simultaneous use of the sorbent Carbopack-X for pumped sampling of certain VOCs. The results were obtained by dosing samplers in a controlled atmosphere test facility (CATFAC) operating under well-defined conditions of concentration, nominal temperature of 20 °C, wind speed of 0.5 m s^?1, and relative humidities of 0% and 80%. Field measurements were also obtained to provide supplementary data to support the laboratory study. Results are compared to existing published data, where these are available.     

Using Si depletion in aerosol to identify the sources of crustal dust in two Chinese megacities

Depletion of Si in transported dust has been recognized for many years. It can be used to distinguish between transported and local dust in cities, although it rarely has been. Here we use the variations of the Si/Al ratio in 15 months of continuous PM_2.5 samples at Beijing (northern China) and Chongqing (southwestern China) to reveal the seasonal patterns of their dust sources. For both cities, peaks of concentration for Si and Al in PM_2.5 corresponded with minima of Si/Al, and could often be linked to pulsed air flow from deserts to the northwest. With significant depletion (up to 80%) and homogeneous distribution at urban and rural sites, Si/Al showed a clear seasonal evolution, which decreased from spring to summer, increased from fall to winter, and collapsed during Chinese Spring Festival, indicating the dominance of transported dust, local fugitive dust and firework influence, respectively. The low ratios implied that desert dust is a common source during spring at Chongqing, whereas its presence during cold season at Beijing was also more frequent than expected. Failing to recognize the depletion of Si may lead to an overestimate of desert dust by 15%–65% when using the average abundance of Al in crust (6%–8%), as in previous studies. The difference in Si/Al ratio between local and transported dust implies that >60% of the dust at Beijing came from outside the city during the springs of 2004–2006. This result can help resolve the contradictory findings on this topic that have been presented earlier.     

PM2.5 and PM10: The influence of sugarcane burning on potential cancer risk

In Brazil, sugarcane fields are often burned to facilitate manual harvesting, and this burning causes environmental pollution from the large amounts of soot released into the atmosphere. This material contains numerous organic compounds such as PAHs. In this study, the concentrations of PAHs in two particulate-matter fractions (PM_2.5 and PM₁₀) in the city of Araraquara (SE Brazil, with around 200,000 inhabitants and surrounded by sugarcane plantations) were determined during the sugarcane harvest (HV) and non-harvest (NHV) seasons in 2008 and 2009. The sampling strategy included four campaigns, with 60 samples in the NHV season and 220 samples in the HV season. The PM_2.5 and PM₁₀ fractions were collected using a dichotomous sampler (10 L min^?1, 24 h) with Teflon? filters. The filter sets were extracted (ultrasonic bath with hexane/acetone (1:1 v/v)) and analyzed by HPLC/Fluorescence. The median concentration for total PAHs (PM_2.5 in 2009) was 0.99 ng m^?3 (NHV) and 3.3 ng m^?3 (HV). In the HV season, the total concentration of carcinogenic PAHs (benz(a)anthracene, benzo(b)fluoranthene, benzo(k)fluoranthene, and benzo(a)pyrene) was 5 times higher than in the NHV season. B(a)P median concentrations were 0.017 ng m^?3 and 0.12 ng m^?3 for the NHV and HV seasons, respectively. The potential cancer risk associated with exposure through inhalation of these compounds was estimated based on the benzo[a]pyrene toxic equivalence (BaP_eq), where the overall toxicity of a PAH mixture is defined by the concentration of each compound multiplied by its relative toxic equivalence factor (TEF). BaP_eq median (2008 and 2009 years) ranged between 0.65 and 1.0 ng m^?3 and 1.2–1.4 ng m^?3 for the NHV and HV seasons, respectively. Considering that the maximum permissible BaP_eq in ambient air is 1 ng m^?3, related to the increased carcinogenic risk, our data suggest that the level of human exposure to PAHs in cities surrounded by sugarcane crops where the burning process is used is cause for concern.     

Influence of roads and inhabited areas on metal concentrations in terrestrial mosses

The guidelines regarding sampling terrestrial mosses for biomonitoring the atmospheric contamination in a region specifically recommend that sampling close to focal points of contamination (i.e. roads, populated areas, etc.) should be avoided for satisfactory characterization of general patterns of contamination. However, these recommendations cannot always be followed in many parts of the world with dense, highly dispersed populations. The aim of the present study was to determine how the distances between sampling sites (SS) and contamination foci such as roads, isolated houses and urban nuclei affect regular, large-scale sampling networks. Metal concentrations obtained in biennial sampling surveys carried out between 2000 and 2006 in Galicia (NW Spain) were used, and the relative proportions of the concentrations corresponding to small-scale and large-scale processes were calculated. The possible relationship between the mean concentrations corresponding to small-scale processes in the different sampling surveys and the distances from SS to roads, buildings and urban nuclei was established by a GIS. Outliers in the data were identified at many of the SS and frequency statistics revealed the absence of any relationship between the distance to these foci and the concentrations of metals in the moss. The method also revealed many instances of the influence of one or more small-scale contamination foci such as airports and railways (often not considered in the sampling recommendations) on SS. Relocation of such SS would improve the representativeness of the sampling grid.