深圳市秋季大气臭氧立体分布特征

利用大气O₃探测激光雷达在深圳市东部生态区和西部城区同步开展垂直观测,探究了2018年深圳市O₃立体分布在秋季光化学污染活跃期至冬季非活跃期的演变过程.结果表明：光化学反应活跃的10月,东部地面O₃浓度相对于西部地面高出约128%;地面向上至450m,O₃浓度在东部生态区发生快速降低,而在西部城区由于存在“滴定效应”,O₃浓度随高度升高而升高;450m~2km,东、西部O₃浓度均随高度升高而降低,西部城区O₃浓度水平超过东部生态区约30%;2km以上高空,东、西部O₃浓度趋同（70μg/m³）,并保持稳定,为具深圳市秋季O₃污染过程提供了较高的大气背景浓度.高污染期间,深圳市大气边界层内O₃浓度变化较为一致,西部高空的O₃区域传输作用更加显著.秋季至冬季光化学反应逐渐减弱,深圳市O₃浓度的水平和垂直空间差异逐渐减小,冬季的深圳市O₃污染基本受大气背景控制.     

深圳大气PM2.5中水溶性有机物的来源特征

对2017年9月~2018年8月深圳市北部大气PM_2.5中水溶性有机物（WSOM）的质量浓度、质谱及来源结构进行测量和分析.结果表明：PM_2.5的质量浓度为（32.3±18.4）μg/m³,WSOM的质量浓度为（9.4±5.7）μg/m³,占颗粒物总有机物的（77.6%±14.0%）.质谱分析显示,WSOM的氧碳比（O/C）平均值达到（0.57±0.09）,属于二次有机物的O/C值范围,且生物质燃烧排放的离子碎片C₂H₄O₂⁺的丰度显著,说明WSOM的来源中有显著的生物质燃烧排放的有机气溶胶.为了明确WSOM的来源结构,利用正矩阵因子分解法（PMF）模型进行来源解析,发现3个合理因子：高氧化态有机气溶胶（MO-OOA）,低氧化态有机气溶胶（LO-OOA）和生物质燃烧（BBOA）,贡献比例分别为51.7%,31.8%和16.5%.MO-OOA和BBOA贡献浓度均呈现秋冬高、春夏低的季节变化特征,反向轨迹分析显示其与内陆污染传输关系密切.LO-OOA的变化相对稳定,本地源的贡献较大.结合¹⁴C同位素示踪法对秋冬季WSOM样品分析,发现机动车等化石源二次有机物是WSOM的主要来源,贡献比例达到53.9%,需继续加强对化石燃料控制来降低WSOM污染.     

机动车轮胎磨损颗粒物化学组分特征研究

为研究机动车道路行驶过程中轮胎磨损排放的颗粒物理化特性,利用轮胎轮廓仿真磨耗仪,对国内主流17种轮胎胎面进行仿真磨耗实验,获得颗粒物样品,提取并检测其中18种元素和20种多环芳烃（PAHs）的含量.结果显示,元素和PAHs含量因轮胎品牌和速度等级的不同而差异显著.18种元素平均含量为（99.04±68.43）mg/g,占样品总重的9.90%,其中Si（88.97±67.85）mg/g、Zn（6.77±1.64）mg/g和Na（1.05±0.75）mg/g的平均含量均超过1mg/g,Cd的含量最低,为（0.43±0.31）μg/g.20种PAHs含量之和（∑20PAHs）在12.13~433.64 μg/g,平均为（94.13±110.18）μg/g,PY的平均含量最高（30.98±31.27）μg/g,其次是CHR、BaP、FA、PHE和BghiP,平均含量最低的是AC（0.58±0.2）μg/g;从环数看,以4环PAHs为主（占∑20PAHs的45.03%~67.93%）,其次为3环（平均含量为15.45%）和5环（平均含量为12.62%）.总体来说,国外品牌轮胎样品中元素和PAHs含量略高于国内品牌,而主要PAHs环数略低于国内品牌.     

城市道路生物滞留带溢流口设计方法探讨

随着生物滞留技术在海绵城市建设中的广泛应用,生物滞留带的优化设计已成为研究热点之一,其中溢流口的合理设计对生物滞留带的雨水径流控制效果和稳定运行具有重要意义。在实际工程应用中,由于缺少溢流口相关水力特性及设计计算方法的系统研究,往往直接把城市道路雨水口移至生物滞留带作为溢流口。然而生物滞留带溢流口与城市道路雨水口水力特征存在较大区别。针对上述问题,通过对生物滞留带溢流口水力特性的分析,计算了常见溢流口的过流能力,并举例对其工程应用选型及设计方法进行了分析,以期为生物滞留带溢流口的优化设计提供依据。     

悬浮填料投加对AnMBR性能及膜污染的影响

研究了悬浮填料投加对分置式厌氧膜生物反应器（AnMBR）的COD去除效果、污泥混合液特性及膜污染的影响。试验结果表明:在反应器有机负荷为2.09 kg/（m3·d）,污泥负荷为0.54 kg/（kg·d）,水力停留时间（HRT）为48 h,温度为（35±2）℃的条件下,与未投加悬浮填料阶段比较,投加填料后AnMBR的COD总去除率由96.6%提高至97.9%,甲烷产率提高16.0%。同时投加悬浮填料后AnMBR混合液污泥平均粒径增大,滤饼层阻力、总阻力、滤饼层阻力在总阻力中的占比较未投加悬浮填料时分别降低7.8、6.5和1.3百分点,溶解性胞外聚合物（SEPS）和结合性胞外聚合物（BEPS）浓度分别降低了20.5%和29.4%,跨膜压差（TMP）线性增长速率降低,膜污染速率明显减缓。因此,投加悬浮填料可在不增加能耗的情况下改善污泥混合液特性,起到强化AnMBR处理效果和控制膜污染的作用。     

Preparation of hydrophobic hierarchical pore carbon–silica composite and its adsorption performance toward volatile organic compounds

Carbon–silica materials with hierarchical pores consisting of micropores and mesopores were prepared by introducing nanocarbon microspheres derived from biomass sugar into silica gel channels in a hydrothermal environment.The physicochemical properties of the materials were characterized by nitrogen physical adsorption(BET),scanning electron microscopy(SEM),and thermogravimetric(TG),and the adsorption properties of various organic waste gases were investigated.The results showed that microporous carbon materials were introduced successfully into the silica gel channels,thus showing the high adsorption capacity of activated carbon in high humidity organic waste gas,and the high stability and mechanical strength of the silica gel.The dynamic adsorption behavior confirmed that the carbon–silica material had excellent adsorption capacity for different volatile organic compounds(VOCs).Furthermore,the carbon–silica material exhibited excellent desorption characteristics:adsorbed toluene was completely desorbed at 150℃,thereby showing superior regeneration characteristics.Both features were attributed to the formation of hierarchical pores.     

中国工业园区绿色发展政策对比分析及对策研究

为了提升我国工业园区绿色发展水平,对目前我国工业园区发展历程、现状特征进行了分析,对工业园区绿色发展政策进行了梳理和对比,并结合工业园区绿色发展中存在的问题提出了对策建议.研究表明:①我国工业园区经历了快速发展、调整发展和科学发展等阶段,在经济发展、资源与能源优化利用、污染减排等方面成效显著.②我国工业园区绿色发展的相关政策主要体现在国家生态工业示范园区创建、园区循环化改造、国家低碳工业园区试点、绿色园区建设和UNIDO绿色工业园区创建等工作中,这些政策在推动主体、实施路径、侧重方向上各不相同又各有特色,对推动工业园区节能减排绩效明显.③目前,我国工业园区绿色发展存在的问题主要表现在重视程度有待提升、风险防范意识有待加强、创新能力有待提高等方面.为此,提出了我国工业园区绿色发展对策建议:积极践行绿色发展理念,推进园区绿色化、生态化、低碳化建设,实现经济环境双赢;注意环境风险防控,确保环境安全;创新管理机制,强化监督管理.      

Plasmonic silver/silver oxide nanoparticles anchored bismuth vanadate as a novel visible-light ternary photocatalyst for degrading pharmaceutical micropollutants

The degradation of pharmaceutical micropollutants is an intensifying environmental problem and synthesis of efficient photocatalysts for this purpose is one of the foremost challenges worldwide. Therefore, this study was conducted to develop novel plasmonic Ag/Ag₂O/BiVO₄ nanocomposite photocatalysts by simple precipitation and thermal decomposition methods, which could exhibit higher photocatalytic activity for mineralized pharmaceutical micropollutants. Among the different treatments, the best performance was observed for the Ag/Ag₂O/BiVO₄ nanocomposites (5 wt.%; 10 min's visible light irradiation) which exhibited 6.57 times higher photodegradation rate than the pure BiVO₄. Further, the effects of different influencing factors on the photodegradation system of tetracycline hydrochloride (TC-HCl) were investigated and the feasibility for its practical application was explored through the specific light sources, water source and cycle experiments. The mechanistic study demonstrated that the photogenerated holes (h⁺), superoxide radicals (?O₂^?) and hydroxyl radicals (?OH) participated in TC-HCl removal process, which is different from the pure BiVO₄ reaction system. Hence, the present work can provide a new approach for the formation of novel plasmonic photocatalysts with high photoactivity and can act as effective practical application for environmental remediation.     

不同浓度锌处理下水稻幼苗对镉的累积效应

为探究锌（Zn）对水稻镉（Cd）累积的影响及其根表铁膜所发挥的作用,选取Cd高累积型水稻品种中9优547（简称"Z547"）和Cd低累积型水稻品种金优402（简称"J402"）,采用温室水培试验,研究0、2、5、10、15和20 μmol/L等6个Zn浓度下水稻幼苗对Cd的累积效应,以及不同浓度Zn处理对根表铁膜生成量的影响.结果表明:①随着c（Zn）的增加,Z547和J402水稻幼苗生物量均呈先增后减的趋势,分别在c（Zn）为2和10 μmol/L时达到最大值.②Z547和J402水稻幼苗中w（Cd）均呈先降后增的趋势,分别在c（Zn）为5和2 μmol/L时达到最小值;当水稻幼苗中w（Cd）达到最小值时,Z547根和地上部中w（Cd）分别为31.65和11.47 mg/kg,J402根和地上部中w（Cd）分别为22.58和14.36 mg/kg.③不同浓度Zn处理下水稻幼苗各部位中w（Cd）均与根表铁膜中w（Mn）、w（Fe）、w（Fe+Mn）呈显著正相关,高铁膜处理水稻幼苗中w（Cd）显著高于低铁膜处理,表明根表铁膜生成量的增加会促进Cd在水稻幼苗中的累积.研究显示,当c（Zn）较低时,c（Zn）的增加会抑制水稻幼苗对Cd的累积;当c（Zn）较高时,c（Zn）的增加会促进水稻幼苗对Cd的累积,而Zn可通过控制根表铁膜的生成来影响水稻幼苗对Cd的累积.      

Chemical characteristics of road dust PM2.5 fraction in oasis cities at the margin of Tarim Basin

In order to understand the compositions characteristics of particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) fraction in road dust (RD_2.5) of oasis cities on the edge of Tarim Basin, 30 road dust (RD) samples were collected in Kashi, Cele, and Yutian in the spring, 2018, and RD_2.5 was collected using the resuspension approach. Eight water-soluble ions, 39 trace elements and 8 fractions of carbon-containing species in PM_2.5 were analyzed. Ca²⁺ and Ca were the most abundant ions and elements in RD_2.5 (7.1% and 9.5%). Cl^- in RD_2.5 was affected not only by attributed to saline-alkali soils in oasis cities of the Tarim Basin and dust from Taklimakan Desert but also by human activities. Moreover, the organic carbon/elemental carbon (OC/EC) ratio indicated that carbon components in RD_2.5 in Cele town mainly come from fossil fuel combustion, while those in Yutian and Kashi mainly come from biomass combustion. It is noteworthy that high Ca in RD_2.5 was seriously affected by anthropogenic emissions, and high Na and K contents in RD_2.5 could be derived from soil and desert dust. It was estimated that Cd, Tl, Sn and Cr were emitted from anthropogenic emissions using the enrichment factor. The coefficients of divergence (COD) result indicated that the influence of local emission on road dust emission is greater than that of long-distance transmission. This study is the first time to comprehensively analyze the chemical characteristics of road dust in oasis cities, and the results provides the sources of road dust at the margin of Tarim Basin.