供水管网生物膜有机物的二氯乙腈与二氯乙酰胺生成特性

在饮用水输配系统中,来源于管壁生物膜的有机物可能耗氯并生成消毒副产物(DBPs),包括二氯乙腈(DCAN)与二氯乙酰胺(DCAcAm)等高毒性含氮DBPs(N-DBPs).研究考察管网常见的细菌与其胞外聚合物(EPS)以及模拟管壁生物膜氯化与氯胺化后DCAN与DCAcAm的生成,并与天然有机物(NOM)和水源水有机物进行比较.结果显示,铜绿假单胞菌、恶臭假单胞菌与藤黄微球菌与氯反应生成的DCAN、DCAcAm浓度分别为1.48～2.02、0.21～0.38μg·mg~(-1)(mg~(-1)以TOC计),高于同反应条件下NOM的生成量;相比于氯化反应,3株细菌细胞氯胺化生成的DCAN与DCAcAm浓度明显更低.3株菌的EPS也是氯与氯胺化反应生成DCAN与DCAcAm的前体物,且其氯胺化反应生成的DCAcAm浓度高于氯化反应生成的.与NOM、水源水相比,模拟管壁生物膜氯化后生成的N-DBPs与三氯甲烷(TCM)浓度比更高,表明生物膜有机物比NOM与水源水有机物更倾向生成DCAN与DCAcAm类N-DBPs,且模拟管壁生物膜氯胺化的DCAcAm生成量高于氯化反应的,说明管壁生物膜有机物是供水管网系统中DCAN与DCAcAm类N-DBPs的重要前体物.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

‘Emulsion locks’ for the containment of hydrocarbons during surfactant flushing

Reversible double water in oil in water (W/O/W) emulsions were developed to contain subsurface hydrocarbon spills during their remediation using surfactant flushing. Double emulsions were prepared by emulsifying CaCl₂ solutions in canola oil, and subsequently by emulsifying the W/O emulsions in aqueous sodium alginate solutions. The formation of double emulsions was confirmed with confocal and optical microscopy. The double emulsions reversed and gelled when mixed with the surfactants sodium dodecyl sulfate (SDS) and cocamidopropyl betaine (CPB). Gels can act as ‘emulsion locks’ to prevent spreading of the hydrocarbon plume from the areas treated with surfactant flushing, as shown in sand column tests. Shear rheology was used to quantify the viscoelastic moduli increase (gelation) upon mixing the double emulsion with SDS and CPB. SDS was more effective than CPB in gelling the double emulsions. CPB and SDS could adsorb at the interface between water and model hydrocarbons (toluene and motor oil), lowering the interfacial tension and rigidifying the interface (as shown with a Langmuir trough). Bottle tests and optical microscopy showed that SDS and CPB produced W/O and O/W emulsions, with either toluene or motor oil and water. The emulsification of motor oil and toluene in water with SDS and CPB facilitated their flow through sand columns and their recovery. Toluene recovery from sand columns was quantitated using Gas-Chromatography Mass-Spectroscopy (GC-MS). The data show that SDS and CPB can be used both for surfactant flushing and to trigger the gelation of ‘emulsion locks’. Ethanol also gelled the emulsions at 100 mL/L.     

Removal and desorption of chromium in synthetic effluent by a mixed culture in a bioreactor with a magnetic field

Two chromium removal experiments were performed in bioreactors with and without a magnetic field under the same conditions.The release of the chromium present in the biomass was tested in two experiments one with the initial pH of the medium and one with pH 4.0.The objective was to remove Cr(Ⅵ) and total Cr from the effluent,this was carried out by placing biological treatments of synthetic effluent contaminated with 100 mg/L of Cr(Ⅵ) in a bioreactor with neodymium magnets that applied a magnetic field(intensity85.4 mT) to the mixed culture.The removal of Cr(Ⅵ) was approximately 100.0% for the bioreactor with a magnetic field and 93,3% for the bioreactor without a magnetic field for9 hr of recirculation of the synthetic effluent by the bioreactor.The removal of total Cr was61.6% and 48.4%,with and without a magnetic field,respectively;for 24 hr.The desorption of Cr(VI) in the synthetic effluent was 0.05 mg/L,which is below the limit established by Brazilian legislation(0.1 mg/L) for the discharge of effluent containing Cr(Ⅵ) into bodies of water.The results obtained for the removal of chromium in synthetic effluent suggested that there was no significant influence on the viable cell count of the mixed culture.The desorption of Cr(Ⅵ) in synthetic effluent after bioadsorption of chromium by the mixed culture in the process of removal of chromium in bioreactors with and without a magnetic field was not significant in either of the experiments with different initial pHs.     

Morphology-dependent interfacial interactions of Fe2O3 with Ag nanoparticles for determining the catalytic reduction of p-nitrophenol

In this work,we fabricated three kinds of Ag/Fe_2O_3 model catalysts with different morphologies to study the interfacial interactions between Ag and Fe_2O_3,and how they affected the catalytic activity in hydrogenation of p-nitrophenol was explored.The hydrothermal method was used to synthesize the metal oxide supported silver catalyst,with various morphologies including nanoplates(NPs),nanospheres(NSs),and nanocubes(NCs).The crystal structure,morphology and surface elements of the composite were investigated by various measurements,such as X-ray diffraction(XRD),scanning electron microscopy(SEM),transmission electron microscopy(TEM) and X-ray photoelectron spectroscopy(XPS).The catalytic activity was also evaluated by the reduction of p-nitrophenol to p-aminophenol.It was found that the activities of the above catalysts varied with the morphology of the support.Among them,Ag/Fe_2O_3 NPs promoted the highest performance,Ag/Fe_2O_3 NSs were slightly inferior,and Ag/Fe_2O_3 NCs were the worst.At last,we ascribed the remarkable activity of Ag/Fe_2O_3 NPs to the strong metal-support interactions between Ag and Fe_2O_3.     

Chemical characteristics of road dust PM2.5 fraction in oasis cities at the margin of Tarim Basin

In order to understand the compositions characteristics of particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) fraction in road dust (RD_2.5) of oasis cities on the edge of Tarim Basin, 30 road dust (RD) samples were collected in Kashi, Cele, and Yutian in the spring, 2018, and RD_2.5 was collected using the resuspension approach. Eight water-soluble ions, 39 trace elements and 8 fractions of carbon-containing species in PM_2.5 were analyzed. Ca²⁺ and Ca were the most abundant ions and elements in RD_2.5 (7.1% and 9.5%). Cl^- in RD_2.5 was affected not only by attributed to saline-alkali soils in oasis cities of the Tarim Basin and dust from Taklimakan Desert but also by human activities. Moreover, the organic carbon/elemental carbon (OC/EC) ratio indicated that carbon components in RD_2.5 in Cele town mainly come from fossil fuel combustion, while those in Yutian and Kashi mainly come from biomass combustion. It is noteworthy that high Ca in RD_2.5 was seriously affected by anthropogenic emissions, and high Na and K contents in RD_2.5 could be derived from soil and desert dust. It was estimated that Cd, Tl, Sn and Cr were emitted from anthropogenic emissions using the enrichment factor. The coefficients of divergence (COD) result indicated that the influence of local emission on road dust emission is greater than that of long-distance transmission. This study is the first time to comprehensively analyze the chemical characteristics of road dust in oasis cities, and the results provides the sources of road dust at the margin of Tarim Basin.     

Nanoencapsulation of hexavalent chromium with nanoscale zero-valent iron: High resolution chemical mapping of the passivation layer

Solid phase reactions of Cr(Ⅵ) with Fe(0) were investigated with spherical-aberration-corrected scanning transmission electron microscopy(Cs-STEM) integrated with X-ray energy-dispersive spectroscopy(XEDS). Near-atomic resolution elemental mappings of Cr(Ⅵ)–Fe(0) reactions were acquired. Experimental results show that rate and extent of Cr(Ⅵ) encapsulation are strongly dependent on the initial concentration of Cr(Ⅵ) in solution. Low Cr loading in nZⅥ(1.0 wt%) promotes the electrochemical oxidation and continuous corrosion of n ZⅥ while high Cr loading(1.0 wt%) can quickly shut down the Cr uptake. With the progress of iron oxidation and dissolution, elements of Cr and O counter-diffuse into the nanoparticles and accumulate in the core region at low levels of Cr(Ⅵ)(e.g., 10 mg/L). Whereas the reacted n ZⅥ is quickly coated with a newly-formed layer of 2–4 nm in the presence of concentrated Cr(Ⅵ)(e.g., 100 mg/L). The passivation structure is stable over a wide range of pH unless pH is low enough to dissolve the passivation layer. X-ray photoelectron spectroscopy(XPS) depth profiling reconfirms that the composition of the newly-formed surface layer consists of Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxides with Cr(Ⅵ) adsorbed on the outside surface. The insoluble and insulating Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxide layer can completely cover the n ZⅥ surface above the critical Cr loading and shield the electron transfer. Thus, the fast passivation of nZⅥ in high Cr(Ⅵ) solution is detrimental to the performance of nZⅥ for Cr(Ⅵ) treatment and remediation.     

Relationship between physicochemical properties and dewaterability of hydrothermal sludge derived from different source

Sewage sludge (SS) and deinking sludge (DS) were used to comparatively study the hydrothermal dewatering of sludge with different components. For a better overview, an insight into the relationship between physicochemical properties and dewaterability of hydrothermal sludge was provided. Results found that not all kinds of sludge were suitably conditioned by hydrothermal treatment (HT) in term of the elevation of dewaterability. Higher hydrothermal temperature tended to enhance the dewaterability of SS rather than DS, which was supported by the variation of their physicochemical properties (including water distribution, bonding energy, extracellular polymeric substance (EPS), particles size, acid functional groups and zeta potential in this study). In addition, the changes in surface morphology suggested that the reverse effect of HT on sludge dewaterability was mainly due to their dewatering behavior. For SS, the destruction of EPS structure leaded to the release of bound water, thereby strengthening sludge dewatering. Conversely, “Bridging effect” generated by lignocellulose in DS was beneficial for sludge dewatering; however, the increasing hydrothermal temperature degraded part of lignocellulose and weakened “bridging effect”, finally resulting in worse dewaterability of DS.