Assessing the efficacy of dissolved air and flash-pressurized flotations using low energy for the removal of organic precursors and disinfection byproducts: a pilot-scale study

Environmental Science and Pollution Research - Dissolved air flotation (DAF) is a widely used treatment process in drinking water and wastewater treatment plants despite high energy cost associated...     

Tool wear of coated drills in drilling CFRP

This study aimed to investigate the wear of certain coated drills when drilling carbon fiber reinforced composites (CFRP). Three different drills were used in the drilling experiments: uncoated, diamond coated and AlTiN coated carbide (WC–Co) drills. The tool wear in CFRP machining was quite different from that in conventional metal machining. The primary wear type was a dulling or blunting of the cutting edge, which has been referred to as edge rounding wear or edge recession. In this paper, a hypothesis has been developed to explain the edge rounding wear in CFRP machining. Due to the fracture-based chip formation of CFRP, there is lack of the work material stagnation zone in front of the cutting edge, which normally prevents the edge wear in metal machining. Series of wear lead to rapid dulling of the cutting edge. The resistance to edge rounding wear on the coated as well as uncoated drills has been investigated. The diamond coating significantly reduces the edge rounding wear. However, AlTiN coated drills showed no visible improvement over the uncoated carbide drill, despite of their high hardness, thus not protecting the drill. The wear mechanisms of the uncoated carbide drill and coatings are discussed. It is believed that the 2-body and 3-body abrasive wear fail to explain the observed tool wear in CFRP drilling. However, the wear of the coatings and uncoated carbide substrate from tribo-meter tests correlated well with the tool wear in the CFRP drilling. Therefore, the tribo-meter test can be used to screen the prospective tool materials before carrying drilling experiment.     

Detection and Molecular Characterization of Human Noroviruses in Korean Groundwater Between 2008 and 2010

RT-PCR, nucleotide sequencing, and phylogenetic analysis were performed for genotyping and molecular characterization of noroviruses isolated from Korean groundwater. Among 160 samples collected from 80 sites between 2008 and 2010, 14 samples (8.7?%) from 12 sites were positive for noroviruses (NoVs). The percentages of NoV-positive samples in 2008, 2009, and 2010 were 22.2, 3.2, and 0?%, respectively, representing a yearly decrease. GII-positive samples (n?=?9, 5.6?%) outnumbered GI-positive samples (n?=?5, 3.1?%). The genotypes of the GI NoVs were GI.2, GI.5, and GI.6, and the genotypes of the GII NoVs were all GII.4. One sample, HM623465, was very similar to CUK-3 and CBNU2 and two GII.4 sequences isolated from the stool of Korean gastroenteritis patients. A BLASTN search revealed several nucleotide sequences highly similar to those of NoVs isolated in this study. The original isolation sources for these similar NoVs were mostly stool (n?=?731, 80.0?%) and groundwater (n?=?135, 14.8?%), and all the countries from which they were isolated were almost in Asia (96.0?%); specifically, China (n?=?192, 21.0?%), Japan (n?=?383, 41.9?%), Korea (n?=?296, 32.4?%), and other Asian countries (n?=?6, 0.7?%). These results suggest that Korean groundwater might be contaminated with NoVs from the stool of infected patients and that these NoVs in turn cause new cases of gastroenteritis through a typical fecal-oral route with region-specific circulation. Therefore, it is important to properly treat sewage, which may include waterborne viruses and manage point sources in groundwater for national health and sanitation. In addition, continuous molecular surveillance remains important for understanding circulating NoVs.     

Fouling distribution in forward osmosis membrane process

Fouling behavior along the length of membrane module was systematically investigated by performing simple modeling and lab-scale experiments of forward osmosis （FO） membrane process. The flux distribution model developed in this study showed a good agreement with experimental results, validating the robustness of the model. This model demonstrated, as expected, that the permeate flux decreased along the membrane channel due to decreasing osmotic pressure differential across the FO membrane. A series of fouling experiments were conducted under the draw and feed solutions at various recoveries simulated by the model. The simulated fouling experiments revealed that higher organic （alginate） fouling and thus more flux decline were observed at the last section of a membrane channel, as foulants in feed solution became more concentrated. Furthermore, the water flux in FO process declined more severely as the recovery increased due to more foulants transported to membrane surface with elevated solute concentrations at higher recovery, which created favorable solution environments for organic adsorption. The fouling reversibility also decreased at the last section of the membrane channel, suggesting that fouling distribution on FO membrane along the module should be carefully examined to improve overall cleaning efficiency. Lastly, it was found that such fouling distribution observed with co-current flow operation became less pronounced in counter- current flow operation of FO membrane process.     

Nitrogen mass balance in a constructed wetland treating piggery wastewater effluent

The nitrogen changes and the nitrogen mass balance in a free water surface flow constructed wetland （CW） using the four-year monitoring data from 2008 to 2012 were estimated. The CW was composed of six cells in series that include the first settling basin （Cell 1）, aeration pond （Cell 2）, deep marsh （Cell 3）, shallow marsh （Cell 4）, deep marsh （Cell 5） and final settling basin （Cell 6）. Analysis revealed that the NH4＋-N concentration decreased because of ammonification which was then followed by nitrification. The NO4＋-N and NO4＋-N were also further reduced by means of microbial activities and plant uptake during photosynthesis. The average nitrogen concentration at the influent was 37,819 kg/year and approximately 45% of that amount exited the CW in the effluent. The denitrification amounted to 34% of the net nitrogen input, whereas the accretion of sediment was only 7%. The biomass uptake of plants was able to retain only 1% of total nitrogen load. In order to improve the nutrient removal by plant uptake, plant coverage in four cells （i.e., Cells 1, 3, 4 and 5） could be increased.     

Characterizing ammonia emissions from swine farms in eastern North Carolina: part 1--conventional lagoon and spray technology for waste treatment

Ammonia (NH3) fluxes from waste treatment lagoons and barns at two conventional swine farms in eastern North Carolina were measured. The waste treatment lagoon data were analyzed to elucidate the temporal (seasonal and diurnal) variability and to derive regression relationships between NH3 flux and lagoon temperature, pH and ammonium content of the lagoon, and the most relevant meteorological parameters. NH3 fluxes were measured at various sampling locations on the lagoons by a flowthrough dynamic chamber system interfaced to an environmentally controlled mobile laboratory. Two sets of open-path Fourier transform infrared (FTIR) spectrometers were also used to measure NH3 concentrations for estimating NH3 emissions from the animal housing units (barns) at the lagoon and spray technology (LST) sites. Two different types of ventilation systems were used at the two farms. Moore farm used fan ventilation, and Stokes farm used natural ventilation. The early fall and winter season intensive measurement campaigns were conducted during September 9 to October 11, 2002 (lagoon temperature ranged from 21.2 to 33.6 degrees C) and January 6 to February 2, 2003 (lagoon temperature ranged from 1.7 to 12 degrees C), respectively. Significant differences in seasonal NH3 fluxes from the waste treatment lagoons were found at both farms. Typical diurnal variation of NH3 flux with its maximum value in the afternoon was observed during both experimental periods. Exponentially increasing flux with increasing surface lagoon temperature was observed, and a linear regression relationship between logarithm of NH3 flux and lagoon surface temperature (T1) was obtained. Correlations between lagoon NH3 flux and chemical parameters, such as pH, total Kjeldahl nitrogen (TKN), and total ammoniacal nitrogen (TAN) were found to be statistically insignificant or weak. In addition to lagoon surface temperature, the difference (D) between air temperature and the lagoon surface temperature was also found to influence the NH3 flux, especially when D > 0 (i.e., air hotter than lagoon). This hot-air effect is included in the statistical-observational model obtained in this study, which was used further in the companion study (Part II), to compare the emissions from potential environmental superior technologies to evaluate the effectiveness of each technology.     

Source characterization of ambient fine particles at multiple sites in the Seattle area

To identify major PM_2.5 (particulate matter ≤2.5 μm in aerodynamic diameter) sources with a particular emphasis on the ship engine emissions from a major port, integrated 24 h PM_2.5 speciation data collected between 2000 and 2005 at five United State Environmental Protection Agency's Speciation Trends Network monitoring sites in Seattle, WA were analyzed. Seven to ten PM_2.5 sources were identified through the application of positive matrix factorization (PMF). Secondary particles (12–26% for secondary nitrate; 17–20% for secondary sulfate) and gasoline vehicle emissions (13–31%) made the largest contributions to the PM_2.5 mass concentrations at all of the monitoring sites except for the residential Lake Forest site, where wood smoke contributed the most PM_2.5 mass (31%). Other identified sources include diesel vehicle emissions, airborne soil, residual oil combustion, sea salt, aged sea salt, metal processing, and cement kiln. Residual oil combustion sources identified at multiple monitoring sites point clearly to the Port of Seattle suggesting ship emissions as the source of oil combustion particles. In addition, the relationship between sulfate concentrations and the oil combustion emissions indicated contributions of ship emissions to the local sulfate concentrations. The analysis of spatial variability of PM_2.5 sources shows that the spatial distributions of several PM_2.5 sources were heterogeneous within a given air shed.     

Seasonal variation in dissolved gaseous mercury and total mercury concentrations in Juam Reservoir, Korea

Dissolved gaseous mercury (DGM) and total mercury (TM) concentrations were measured in Juam Reservoir, Korea. DGM concentrations were higher in spring (64+/-13pgL(-1)) and summer (109+/-15pgL(-1)), and lower in fall (20+/-2pgL(-1)) and winter (23+/-6pgL(-1)). In contrast, TM concentrations were higher in fall (3.2+/-0.1ngL(-1)) and winter (3.3+/-0.1ngL(-1)) than in spring (2.3+/-0.1ngL(-1)) and summer (2.2+/-0.4ngL(-1)). DGM concentrations were correlated with water temperature (p<0.0001), ORP (p<0.0001), UV intensity (UV-A: p=0.008; UV-B: p=0.003), and DOC concentration (p=0.0107). DGM concentrations varied diurnally with UV intensity. The average summer DGM (109+/-15pgL(-1)) and TM (2.2+/-0.4ngL(-1)) concentrations in Juam Reservoir were higher than the averages for North American lakes (DGM=38+/-16pgL(-1); TM=1.0+/-1.2ngL(-1)), but lower than levels reported for Baihua Reservoir in China.     

Relationships between organic matter, black carbon and persistent organic pollutants in European background soils: Implications for sources and environmental fate

Black carbon (BC) and total organic carbon (TOC) contents of UK and Norwegian background soils were determined and their relationships with persistent organic pollutants (HCB, PAHs, PCBs, co-planar PCBs, PBDEs and PCDD/Fs) investigated by correlation and regression analyses, to assess their roles in influencing compound partitioning/retention in soils. The 52 soils used were high in TOC (range 54-460 mg/g (mean 256)), while BC only constituted 0.24-1.8% (0.88%) of the TOC. TOC was strongly correlated (p < 0.001) with HCB, PCBs, co-PCBs and PBDEs, but less so with PCDD/Fs (p < 0.05) and PAHs. TOC explained variability in soil content, as follows: HCB, 80%; PCBs, 44%; co-PCBs, 40%; PBDEs, 27%. BC also gave statistically significant correlations with PBDEs (p < 0.001), co-PCBs (p < 0.01) and PCBs, HCB, PCDD/F (p < 0.05); TOC and BC were correlated with each other (p < 0.01). Inferences are made about possible combustion-derived sources, atmospheric transport and air-surface exchange processes for these compounds.     

Chlorinated naphthalene formation from the oxidation of dichlorophenols

Polychlorinated naphthalenes (PCNs) formed along with dibenzo-p-dioxin and dibenzofuran products in the slow combustion of dichlorophenols (DCPs) at 600 degrees C were identified. Each DCP reactant produced a unique set of PCN products. Major PCN congeners observed in the experiments were consistent with products predicted from a mechanism involving an intermediate formed by ortho-ortho carbon coupling of phenoxy radicals; polychlorinated dibenzofurans (PCDFs) are formed from the same intermediate. Tautomerization of the intermediate and H2O elimination produces PCDFs; alternatively, CO elimination to form dihydrofulvalene and fusion produces naphthalenes. Only trace amounts of tetrachloronaphthalene congeners were formed, suggesting that the preferred PCN formation pathways from chlorinated phenols involve loss of chlorine. 3,4-DCP produced the largest yields of PCDF and PCN products with two or more chlorine substituents. 2,6-DCP did not produce tri- or tetra-chlorinated PCDF or PCN congeners. It did produce 1,8-DCN, however, which could not be explained.