Rotary Kiln Incineration III. An Indepth Study—Kiln Exit/Afterburner/Stack Train and Kiln Exit Pattern Factor Measurements During Liquid CCl4 Processing

Temperature and stable species concentration data are presented from various locations within a full-scale rotary kiln incinerator firing natural gas/carbon tetrachloride/air. The data are being collected as part of a cooperative program involving university, industry and government participation. The overall goal of the program is to develop a more sophisticated understanding of and a predictive capability for rotary kiln and afterburner performance as influenced by basic design and operational parameters. Non-uniformities in stable species and temperature exist for this particular kiln, at the kiln exit, under certain operating conditions. Flow perturbations from within the kiln were found to persist into the afterburner, but not into the stack. High destruction and removal efficiencies (DRE’s) were achieved under the operating conditions of these tests through adequate secondary combustion processing.     

Guidance for the Field Demonstration of Remediation Technologies

This paper will focus on the demonstration of hazardous waste cleanup technologies in the field. The technologies will be at the pilot- or full-scale, and further referred to as field-scale. The main objectives of demonstration at the field-scale are development of reliable performance and cost data. Technology demonstrations provide performance, cost effectiveness, and reliability data so that potential technology users have sufficient information to make effective decisions as to the applicability of the technology to a specific situation. The demonstration and evaluation of a technology should be conducted with the purpose of characterizing performance, need for pre- and post-processing of the waste feed, identification of waste type and constituents applicable to the technology, system throughput, problems and limitations of the technology, and operating and maintenance costs. Table I provides a summary of remediation activities for demonstration projects.     

Rotary Kiln Incineration IV. An Indepth Study— Kiln Exit,Transition and Afterburner Sampling During Liquid CCl4 Processing

Detailed temperature and stable species concentration data are presented from the kiln exit, transition section and afterburner of a full-scale incinerator facility firing natural gas/carbon tetrachloride/air. The data are collected as part of a cooperative program involving university, industry and government participation. The overall goal of the program is to develop an understanding and predictive capability for rotary kiln and afterburner performance as influenced by basic design and operational parameters. The data demonstrate that nonuniformities in stable species and temperature exist, under certain operating conditions, at the kiln exit in the vertical direction only. Measurements from the transition section indicate that non-uniformities may exist within this region under certain operating conditions. Flow perturbations from within the kiln can persist into the afterburner, although the degree of nonuniformity is substantially reduced compared to either the kiln or transition sections. High destruction and removal efficiencies were achieved under all operating conditions of these tests through a combination of kiln and secondary combustion processing.     

Evaluating Sources of Indoor Air Pollution

Evaluation of Indoor air pollution problems requires an understanding of the relationship between sources, air movement, and outdoor air exchange. Research is underway to investigate these relationships. A three-phase program is being implemented: 1) Environmental chambers are used to provide source emission factors for specific indoor pollutants; 2) An IAQ (Indoor Air Quality) model has been developed to calculate indoor pollutant concentrations based on chamber emissions data and the air exchange and air movement within the indoor environment; and 3) An IAQ test house is used to conduct experiments to evaluate the model results. Examples are provided to show how this coordinated approach can be used to evaluate specific sources of indoor air pollution. Two sources are examined: 1) para-dichlorobenzene emissions from solid moth repellant; and 2) particle emissions from unvented kerosene heaters.

The evaluation process for both sources followed the three-phase approach discussed above. Para-dichlorobenzene emission factors were determined by small chamber testing at EPA’s Air and Energy Engineering Research Laboratory. Particle emission factors for the kerosene heaters were developed In large chambers at the J. B. Pierce Foundation Laboratory. Both sources were subsequently evaluated in EPA’s IAQ test house. The IAQ model predictions showed good agreement with the test house measurements when appropriate values were provided for source emissions, outside air exchange, in-house air movement, and deposition on “sink” surfaces.     

The Effects of Infiltration and Insulation on the Source Strengths and Indoor Air Pollution from Combustion Space Heating Appliances

Many energy conservation strategies for residences involve reducing house air exchange rates. Reducing the air exchange rate of a house can cause an increase in pollutant levels if there is an indoor pollution source and if the indoor pollutant source strength remains constant. However, if the indoor pollutant source strength can also be reduced, then it is possible to maintain or even improve indoor air quality. Increasing the insulation level of a house is a means of achieving energy conservation goals and, in addition, can reduce the need for space heating and thereby reduce the pollutant source strengths of combustion space heaters such as unvented kerosene space heaters, unvented gas space heaters, and wood stoves. In this paper, the indoor air quality trade-off between reduced infiltration and increased insulation in residences is investigated for combustion space heaters. Two similar residences were used for the experiment. One residence was used as a control and the other residence had infiltration and insulation levels modified. An unvented propane space heater was used as the source in this study. A model was developed to describe the dependence of both indoor air pollution levels and the appliance source strengths on house air exchange rates and house insulation levels. Model parameters were estimated by applying regression techniques to the data. Results show that indoor air pollution levels in houses with indoor combustion space heating pollution sources can be held constant (or lowered) by reducing the thermal conductance by an amount proportional to (or greater than) the reduction of the air exchange rate.     

Assessment of Needs for Technical Information in EPA’s Hazardous and Solid Waste Programs

Headquarters managers and Regional staff in the U.S. Environmental Protection Agency’s hazardous and solid waste programs were surveyed to determine priorities for technical information and guidance among EPA Regional staff, state hazardous waste management staff, EPA contractors, and the regulated community. The survey also examined delivery systems effective for EPA Regional staff. The fifteen highest ranked technical needs for RCRA, Superfund, and UST reflect a pervasive interest in hazardous waste remediation. Top priority technical needs focus on establishing cleanup levels, subsurface fate and transport, field monitoring and quality assurance, remedy selection, and most importantly, which remedies work and which do not in specific situations. Technical needs of non- EPA audiences are quite similar to those for EPA field staff. Preferences for technology transfer delivery systems are generally for conventional distribution methods (such as print materials and workshops) rather than electronic or video media. Regional staff report serious problems in utilizing technology transfer because of time constraints, insufficient knowledge of available products, insufficient travel funds, and limited access to and training on computers.     

Polymers as Solid Waste in Municipal Landfills

Abstract

Synthetic polymers reach municipal landfills as components of products such as waste household paints, packaging films, storage containers, carpet fibers, and absorbent sanitary products. Some polymers in consumer products that reach landfills are designed to photodegrade or biodegrade. This article examines the significance of degradable polymers in management of solid waste in municipal landfills. Most landfills are not designed to photodegrade or biodegrade solid waste. Landfill disposal of stable polymers such as polyacrylics and polyethylenes is not associated with significant polymer degradation or mobility. Stability to photodegradation and biodegradation is an advantage when municipal landfills are used for disposal of polymer products as solid waste. Use of landfill disposal can be a responsible means to manage polymer waste and can be part of an overall waste management plan which includes source reduction, recycling, reuse, composting, and waste-to-energy incineration.     

Effectiveness of Smokeless Ashtrays

Abstract

Most environmental tobacco smoke (ETS) issues from the tips of smoldering cigarettes between puffs. Smokeless ashtrays are designed to reduce ETS exposure by removing particulate and/or gas-phase contaminants from this plume. This paper describes an experimental investigation of the effectiveness of four smokeless ashtrays: two commercial devices and two prototypes constructed by the authors. In the basic experimental protocol, one or more cigarettes was permitted to smolder in a room. Particulate or gas-phase pollutant concentrations were measured in the room air over time. Device effectiveness was determined by comparing pollutant concentrations with the device in use to those obtained with no control device. A lung deposition model was applied to further interpret device effectiveness for particle removal. The commercial ashtrays were found to be substantially ineffective in removing ETS particles because of the use of low-quality filter media and/or the failure to draw the smoke through the filter. A prototype ashtray using HEPA filter material achieved better than 90% particle removal efficiency. Gasphase pollutant removal was tested for only one prototype smokeless ashtray, which employed filters containing activated carbon and activated alumina. Removal efficiencies for the 18 gas-phase compounds measured (above the detection limit) were in the range of 70 to 95%.     

Mapping Odor Sources from Complaint Statistics I: Identifying the Major Source

Odor is acknowledged as a major community air pollution nuisance, but the problems of analysis, particularly in Identifying the origin of odor, are also well recognised. One approach to the problem has been the development of computational schemes which use wind directions at the times of odor observations to locate the likely source of odor. An earlier technique, PONG, has now been superseded by a more sophisticated version, PONG2, which incorporates Gaussian plume modeling techniques. This paper describes the operation of PONG2 in the odor source mapping mode and provides an analysis of the Insensitivity of the technique to errors in input. Then, using specific Australian examples of community odor nuisance emanating from a large sewage treatment complex near Melbourne, and an irrigated golf course within metropolitan Darwin, the paper outlines the utility of PONG2 in resolving problem odor sources at a range of scales and levels of complexity.