Phytopumping for hydraulic control of an arsenic plume

Phytoremediation, the use of plants for in situ contaminant cleanup, is gaining new appreciation as an aesthetically pleasing, sustainable method that naturally makes use of solar power. Hybrid poplars are widely used because they grow rapidly and have high transpiration rates, making them advantageous for hydraulic control of groundwater. However, the tendency for trees and other vegetation to uptake metals may be a disadvantage in some settings due to potential redistribution of metals from groundwater to the ground surface. Therefore, a pilot test in the upper midwestern United States was implemented to evaluate the applicability of poplars to groundwater withdrawal and metals transport. © 2009 Wiley Periodicals, Inc.     

Estimation of Ambient PM2.5 Concentrations in Maryland and Verification by Measured Values

Abstract

In 1997, Maryland had no available ambient Federal Reference Method data on particulate matter less than 2.5 μm in aerodynamic diameter (PM_2.5), but did have annual ambient data for PM smaller than 10 μm (PM₁₀) at 24 sites. The PM₁₀ data were analyzed in conjunction with local annual and seasonal zip-code-level emission inventories and with speciated PM_2.5 data from four nearby monitors in the IMPROVE network (located in the national parks, wildlife refuges, and wilderness areas) in an effort to estimate annual average and seasonal high PM_2.5 concentrations at the 24 PM₁₀ monitor sites operating from 1992 to 1996. All seasonal high concentrations were estimated to be below the 24-hr PM_2.5 National Ambient Air Quality Standards (NAAQS) at the sites operating in Maryland between 1992 and 1996. The estimates also indicated that 12 monitor sites might exceed the 3-year annual average PM_2.5 NAAQS of 15 ug/m³, but Maryland’s air quality shows signs that it has been improving since 1992. The estimates also were compared with actual measurements after the PM_2.5 monitor network was installed. The estimates were adequate for describing the chemical composition of the PM_2.5, forecasting compliance status with the 24-hr and annual standards, and determining the spatial variations in PM_2.5 across central Maryland.     

Derivation of synthetic fuel from waste plastic: investigation of engine operating characteristics on DI diesel engine

The utilization of plastic in day to day life is ever-increasing and has generated a large amount of plastic garbage that needs proper disposal to save the environment from harmful pollution. The plastic waste management becomes a pressing concern in the present scenario in developing countries like India. This research article evaluates the potential of synthetic fuel (SF) derived from waste plastics collected from the local shops. In this current investigation, the SF blends are tested in a direct injection diesel engine to analyze the performance and emission characteristics of the engine. Three different blends were made namely SF20, SF40, and SF60 on a volumetric basis and the tests were carried out. From the experimental results, it was found that brake thermal efficiency (BTE) of the fuel blends was reduced as compared with neat diesel operation regardless of loads whereas SF20 showed a similar trend as that of diesel operation. The analysis of the emission characteristics revealed that the SF20 blends reduced dangerous smoke and carbon monoxide emission as compared with other test fuels. From the overall results, SF20 showed superior performance and emission aspects as compared with other SF blends whereas the engine operated smoothly up to 60% of SF blending at all loading conditions.

     

Hepatotoxicity of graphene oxide in Wistar rats

Environmental Science and Pollution Research - Graphene oxide (GO) has a multitude of applications in areas of nanomedicine, electronics, textile, water purification, and catalysis among others. GO...     

Predicting the combustion behaviour of compression ignition engine fuelled with biodiesel from Stoechospermum marginatum,a macro algae

Environmental Science and Pollution Research - Biodiesel is one among the recent developments in the field of renewable energy research. To enhance the combustion characteristics of compression...     

Influence of coagulation mechanisms and floc formation on filterability

Minimizing particles in water is a key goal for improving drinking water quality and safety.The media filtration process,as the last step of the solid–liquid separation process,is largely influenced by the characteristics of flocs,which are formed and controlled within the coagulation process.In a laboratory-based study,the impacts of the physical characteristics of flocs formed using aluminum sulfate on the filtration treatment of two comparative water samples were investigated using a photometric dispersion analyzer and a filterability apparatus.In general,the optimum dosage for maximizing filterability was higher than that for minimizing turbidity under neutral p H conditions.For a monomeric aluminum-based coagulant,the charge neutralization mechanism produced better floc characteristics,including floc growth speed and size,than the sweep flocculation mechanism.In addition,the charge neutralization mechanism showed better performance compared to sweep flocculation in terms of DOC removal and floc filterability improvement for both waters,and showed superiority in turbidity removal only when the raw water had high turbidity.For the different mechanisms,the ways that floc characteristics impacted on floc filterability also differed.The low variation in floc size distribution obtained under the charge neutralization mechanism resulted in the flocs being amenable to removal by filtration processes.For the sweep flocculation mechanism,increasing the floc size improved the settling ability of flocs,resulting in higher filter efficiency.     

Tissue distribution of perfluoroalkyl acids and health status in wild Mozambique tilapia (Oreochromis mossambicus) from Loskop Dam, Mpumalanga, South Africa

This study examined concentrations of 15 perfluoroalkyl acids (PFAAs) in tissues from male Mozambique tilapia (Oreochromis mossambicus) collected at Loskop Dam, Mpumalanga, South Africa in 2014 and 2016. Nine of the 15 PFAAs were detected frequently and were included in statistical analysis and included two of the most commonly known PFAAs, perfluorooctanesulfonic acid (PFOS) (median, 41.6 ng/g) and perfluorooctanoic acid (PFOA) (median, 0.0825 ng/g). Of the tissues measured, plasma (2016 and 2014 median, 22.2 ng/g) contained the highest PFAA burden followed by (in descending order): liver (median, 11.6 ng/g), kidney (median, 9.04 ng/g), spleen (median, 5.92 ng/g), adipose (median, 2.54 ng/g), and muscle (median, 1.11 ng/g). Loskop Dam tilapia have been affected by an inflammatory disease of the adipose tissue known as pansteatitis, so this study also aimed to investigate relationships between PFAA tissue concentrations and incidence of pansteatitis or fish health status. Results revealed that healthy tilapia exhibited an overall higher (p-value < 0.05) PFAA burden than pansteatitis-affected tilapia across all tissues. Further analysis showed that organs previously noted in the literature to contain the highest PFAA concentrations, such as kidney, liver, and plasma, were the organs driving the difference in PFAA burden between the two tilapia groups. Care must be taken in the interpretations we draw from not only the results of our study, but also other PFAA measurements made on populations (human and wildlife alike) under differing health status.     

Use of Preservative Agents and Antibiotics for Increased Poliovirus Survival on Positively Charged Filters

Environmental surveillance of poliovirus (PV) and other non-enveloped viruses can help identify silent circulation and is necessary to certify eradication. The bag-mediated filtration system is an efficient method to filter large volumes of environmental waters at field sites for monitoring the presence of viruses. As filters may require long transit times to off-site laboratories for processing, viral inactivation or overgrowth of bacteria and fungi can interfere with virus detection and quantification (Miki and Jacquet in Aquatic Microb Ecol 51(2):195–208, 2008). To evaluate virus survival over time on ViroCap^? filters, the filters were seeded with PV type 1 (PV1) and/or MS2 and then dosed with preservatives or antibiotics prior to storage and elution. These filters were stored at various temperatures and time periods, and then eluted for PV1 and MS2 recovery quantification. Filters dosed with the preservative combination of 2% sodium benzoate and 0.2% calcium propionate had increased virus survival over time when stored at 25 °C, compared to samples stored at 25 °C with no preservatives. While elution within 24 h of filtration is recommended, if storage or shipping is required then this preservative mixture can help preserve sample integrity. Addition of an antibiotic cocktail containing cephapirin, gentamicin, and Proclin^? 300 increased recovery after storage at 4 and 25 °C, when compared to storage with no antibiotics. The antibiotic cocktail can aid sample preservation if access to appropriate antibiotics storage is available and sample cold chain is unreliable. This study demonstrated that the use of preservatives or antibiotics is a simple, cost-effective method to improve virus detection from ViroCap cartridge filters over time.     

Resistance mash welding for joining of copper conductors for electric motors

The automotive industry is developing designs and manufacturing processes for a new generation of electric motors intended for use in hybrid and electric vehicles. This paper is focused on using solid-state welding to join rectangular wires in the fabrication of motor stators. Resistance welding has not typically been applied to copper due to its very high electrical conductivity; however through optimization of the current and pressure profiles, excellent quality copper-to-copper joints have been demonstrated with a technique known as resistance mash welding. A better understanding of resistance mash welding characteristics will help advancements in its application for stators. The limitations of this application will be discussed.