The Contribution of Marsh Zones to Water Quality in Dutch Shallow Lakes: A Modeling Study

Many lakes have experienced a transition from a clear into a turbid state without macrophyte growth due to eutrophication. There are several measures by which nitrogen (N) and phosphorus (P) concentrations in the surface water can be reduced. We used the shallow lake model PCLake to evaluate the effects of three measures (reducing external nutrient loading, increasing relative marsh area, and increasing exchange rate between open water and marsh) on water quality improvement. Furthermore, the contribution of different retention processes was calculated. Settling and burial contributed more to nutrient retention than denitrification. The model runs for a typical shallow lake in The Netherlands showed that after increasing relative marsh area to 50%, total phosphorous (TP) concentration in the surface water was lower than the Maximum Admissible Risk (MAR, a Dutch government water quality standard) level, in contrast to total nitrogen (TN) concentration. The MAR levels could also be achieved by reducing N and P load. However, reduction of nutrient concentrations to MAR levels did not result in a clear lake state with submerged vegetation. Only a combination of a more drastic reduction of the present nutrient loading, in combination with a relatively large marsh cover (approximately 50%) would lead to such a clear state. We therefore concluded that littoral marsh areas can make a small but significant contribution to lake recovery.     

Size distributions of fine and ultrafine particles in the city of Strasbourg: correlation between number of particles and concentrations of NO(x) and SO(2) gases and some soluble ions concentration determination

An Electrical Low Pressure Impactor (ELPI) was used during spring and autumn 2003 in the centre of Strasbourg for the measurement of atmospheric aerosols size distribution. The concentration of NO(x) and SO(2) in air was simultaneously measured with specific analysers. Samples were collected in the range 0.007-10 microm in equivalent aerodynamic diameter size. Number distributions are representative of a pollution originating from urban traffic with a particle size distribution exhibiting a nucleation mode below 29 nm and an accumulation mode around 80 nm in size. A mean particle density equal to 39000+/-35000 total particles per cm(3) with a size ranging from 7 to 10 microm was obtained after a sampling period of 2 weeks in spring. About 86.9% of the number of particles have an aerodynamic diameter below 0.1 microm and 13.1% between 0.1 and 1 microm. Correlation coefficients between the number of particles impacted on each ELPI plate and gas concentrations (SO(2) and NO(x)) showed that the numbers of particles with diameter between 0.10 and 0.62 microm are highly related to the NO(x) concentration. This result indicates that particles are traffic induced since NO(x) is mainly emitted by cars as shown by measurements on various sites. Particles are less clearly correlated to the SO(2) concentration. Particle analysis on different ELPI plates for a sampling period of 2 weeks in autumn showed high level of soluble NO(3)(-), SO(4)(2-) and NH(4)(+) ions. Indeed, up to 90% b.w. of these three species were found in the particle range 0.1-1 microm. The formation of particulate NH(4)NO(3) is favoured by high NO(x) concentration, which induces the formation of gaseous HNO(3).     

Effect of mono-ortho and di-ortho substituted polychlorinated biphenyl (PCB) congeners on leopard frog survival and sexual development

We tested the effect of mono-ortho and di-ortho PCB congeners on northern leopard frog (Rana pipiens) hatching success, survival and sexual development. Embryos and tadpoles were exposed to two levels (0.5 and 50 microg/l) of two PCBs. PCBs 101 and 70 were selected because they were present in amphibians collected in the Fox River-Green Bay ecosystem and they have the theoretical structural requirements to be able to bind to the estrogen receptor and mediate estrogenic responses. The exposure of leopard frog embryos and tadpoles to PCB 70 and 101 did not significantly affect hatchability, survival, deformities or growth. There were significant departures from the expected 50:50 sex ratio in tadpoles/froglets exposed to PCB 101 and PCB 70. In all the cases of significant departure, the bias was towards higher number of females. Decrease in the proportion of male gonads and increase in the proportion of intersex gonads were observed with increasing PCB tissue concentrations. The effects of PCB congeners on sexual differentiation occur at concentrations higher than observed in frogs in the Fox River/Green Bay ecosystem.     

Analysis of perfluorooctanoate (PFOA) and other perfluorinated compounds (PFCs) in the River Po watershed in N-Italy

C7-C11 perfluorinated carboxylates (PFACs) and perfluorooctansulfonate (PFOS) were analysed in selected stretches of the River Po and its major tributaries. Analyses were performed by solid-phase extraction (SPE) with Oasis HLB cartridges and methanol elution followed by LC-MS-MS detection using 13C-labelled internal standards. High concentration levels ( approximately 1.3 microg l(-1)) of perfluorooctanoate (PFOA) were detected in the Tánaro River close to the city Alessandria. After this tributary, levels between 60 and 337 ng l(-1) were measured in the Po River on several occasions. The PFOA concentration close to the river mouth in Ferrara was between 60 and 174 ng l(-1). Using the river discharge flow data in m3 s(-1) at this point (average approximately 920 m3 s(-1) for the year 2006), a mass load of approximately 0.3 kg PFOA per hour or approximately 2.6 tons per year discharged in the Adriatic Sea has been calculated. PFOS concentration levels in the Po River at Ferrara were approximately 10 ng l(-1).     

Multiscale analysis of heavy metal contents in Spanish agricultural topsoils

This study characterized and mapped the spatial variability patterns of seven topsoil heavy metals (Cr, Ni, Pb, Cu, Zn, Hg and Cd) within the Ebro river basin (9.3 million ha) by Multivariate Factorial Kriging. The variograms and cross-variograms of heavy metal concentrations showed the presence of multiscale variation that was modeled using three variogram models with ranges of 20km (short-range), 100km (medium-range) and 225km (long-range). Our results indicate that the heavy metal concentration is influenced by bedrock composition and dynamics at all the spatial scales, while human activities have a notorious effect only at the short- and medium-range scale of variation. Sources of Cu, Pb and Zn (and secondary Cd) are associated with agricultural practices (at the short-range scale of variation), whereas Hg variation at the short- and medium-range scale of variation is related to atmospheric deposition.     

Traffic and catalytic converter - related atmospheric contamination in the metropolitan region of the city of Rio de Janeiro, Brazil

In this work, 24-h PM10 samples were collected in Rio de Janeiro, Brazil, and analysed for trace elements (Cd, Ce, Cu, La, Mo, Ni, Pb, Pd, Rh, Sb and Sn). The sampling was carried out at five locations (Bonsucesso; Centro, downtown city; Copacabana; Nova Igua?u and Sumaré) with different traffic densities and anthropogenic activities. An analytical method based on the EPA method for the determination of trace elements in airborne particulate matter (PM), using ultrasonic-assisted extraction and inductively coupled plasma mass spectrometry (ICP-MS) was applied. Our results suggest that vehicular traffic is the most important source of environmental pollution at the studied sites. The presence of Mo, Pd and Rh in the analysed filters reflects an additional source of pollution caused by the erosion and deterioration of automotive catalytic converters.     

Coupled solar photo-Fenton and biological treatment for the degradation of diuron and linuron herbicides at pilot scale

A coupled solar photo-Fenton (chemical) and biological treatment has been used to remove biorecalcitrant diuron (42 mg l(-1)) and linuron (75 mg l(-1)) herbicides from water at pilot plant scale. The chemical process has been carried out in a 82 l solar pilot plant made up by four compound parabolic collector units, and it was followed by a biological treatment performed in a 40 l sequencing batch reactor. Two Fe(II) doses (2 and 5 mg l(-1)) and sequential additions of H2O2 (20 mg l(-1)) have been used to chemically degrade the initially polluted effluent. Next, biodegradability at different oxidation states has been assessed by means of BOD/COD ratio. A reagent dose of Fe=5 mg l(-1) and H2O2=100 mg l(-1) has been required to obtain a biodegradable effluent after 100 min of irradiation time. Finally, the organic content of the photo-treated solution has been completely assimilated by a biomass consortium in the sequencing batch reactor using a total suspended solids concentration of 0.2 g l(-1) and a hydraulic retention time of 24h. Comparison between the data obtained at pilot plant scale (specially the one corresponding to the chemical step) and previously published data from a similar system performing at laboratory scale, has been carried out.     

Mineralization of the biocide chloroxylenol by electrochemical advanced oxidation processes

Electrochemical advanced oxidation processes (EAOPs) are environmentally friendly methods based on the destruction of organic pollutants in wastewaters with in situ electrogenerated hydroxyl radical. This species is formed in anodic oxidation (AO) from water oxidation at the anode and in indirect electro-oxidation methods like electro-Fenton (EF) and photoelectro-Fenton (PEF) also from reaction between catalytic Fe2+ and H2O2 continuously produced at the O2-diffusion cathode. The PEF method involves the irradiation of the treated solution with UVA light to enhance the photolysis of organics including Fe(III) complexes. In this work, the oxidation power of such EAOPs to decontaminate synthetic wastewaters of the biocide chloroxylenol (4-chloro-3,5-dimethylphenol) at pH 3.0 is comparatively examined with an undivided electrolytic cell containing a Pt or boron-doped diamond (BDD) anode and a stainless steel or O2-diffusion cathode. The initial chlorine is released as Cl(-) ion, which remains stable in the medium using Pt or is oxidized to Cl2 on BDD. The biocide solutions can be completely decontaminated using AO with a BDD anode, as well as PEF with a Pt or BDD anode. The PEF procedure with a BDD anode is the most powerful method leading to total mineralization in about 300 min, practically independent of current density. When current density rises, the degradation rate of processes increases, but they become less efficient due to the larger enhancement of waste reactions of oxidants. Chloroxylenol is much more rapidly removed in EF and PEF than in AO. 2,6-dimethylhydroquinone, 2,6-dimethyl-p-benzoquinone and 3,5-dimethyl-2-hydroxy-p-benzoquinone are identified as aromatic by-products, and maleic, malonic, pyruvic, acetic and oxalic acids are found as generated carboxylic acids. A general pathway for chloroxylenol mineralization by all EAOPs including the above by-products is proposed.     

High chrome exhaustion in a non-float tanning process using a sulphonic aromatic acid

Tanning processes performed in drums consume large amounts of water and chemicals, most of which end up in the wastewater. This study explores an alternative approach at an industrial scale to the traditional pickle-chrome tanning method. The new method replaces formic and sulphuric acids with sulphonic aromatic acid. Because it is done without float, there is a sizeable reduction in the amount of added salt and chrome salt as well as an increase in temperatures at the end of the tanning process. From an environmental perspective, the new method offers important advantages. For instance, there is no float addition in the tannage. Also, there are reductions of 94% and 99%, respectively, in the discharge of chlorides and chrome, as well as a 75% reduction in the residual float. Our financial assessment demonstrated that the new method is 42% cheaper than a traditional approach.     

Minimization of the environmental impact in the unhairing of bovine hides

This study tests an alternative method to the traditional unhairing method used during the process of tanning the hides. The new method is based on the substitution of sodium sulfide by hydrogen peroxide as an unhairing agent in both hair recovery and recirculation of the floats employed in the process. The properties of the hides obtained using the two methods have been compared and the results indicate that those hides have similar physical, chemical, and organoleptic properties. However, the differences existing from an environmental point of view are significant. These include reductions of water consumption (approx 70%), chemical oxygen demand (approx 35%), toxicity (98%) and total kjendhal nitrogen (50%). Also, the risk associated with the production of hydrogen sulfide is eliminated, which implies a great improvement in terms of safety for the workers. Given the large amounts of water and chemical pollution discharged in the process, the reductions in absolute values represent a significant improvement. A financial assessment was carried out to demonstrate that the proposed new system is 16% more economic than the traditional one.