Accelerated soil dissipation of tebuconazole following multiple applications to peanut

Repeated application may increase rates of pesticide dissipation in soil and reduce persistence. The potential for this to occur was investigated for the fungicide, tebuconazole (alpha-[2-(4-chlorophenyl)ethyl]-alpha-(1,1-dimethylethyl)-1H-1,2,4-triazole-1-ethanol), when used for peanut (Arachis hypogaea L.) production. Soil samples were collected from peanut plots after each of four tebuconazole applications at 2-wk intervals. Soil moisture was adjusted to field capacity as necessary and samples were incubated in the laboratory for 63 d at 30 degrees C. Untreated plot samples spiked with the compound served as controls. Results indicated accelerated dissipation in field-treated samples with the time to fifty percent dissipation (DT50) decreasing from 43 to 5 d after three tebuconazole applications. Corresponding increases in rates of accumulation and decay of degradates were also indicated. Best-fit equations (r2 = 0.84-0.98) to dissipation kinetic data combined with estimates of canopy interception rates were used to predict tebuconazole and degradates concentration in soil after each successive application. Predicted concentrations compared with values measured in surface soil samples were from twofold less to twofold greater. Use of kinetic data will likely enhance assessments of treatment efficacy and human and ecological risks from normal agronomic use of tebuconazole on peanut. However, the study indicated that varying soil conditions (in particular, soil temperature and water content) may have an equal or greater impact on field dissipation rate than development of accelerated dissipation. Results emphasize that extension of laboratory-derived kinetic data to field settings should be done with caution.     

HISTORICAL TRENDS IN SEDIMENTATION RATES AND SEDIMENT PROVENANCE,FAIRFIELD LAKE,WESTERN NORTH CAROLINA1

Sedimentation rates and sediment provenance were examined for lacustrine sediments deposited in Fairfield Lake, western North Carolina, during the past 111 years. Stratigraphic, radionuclide, and cartographic data indicate that sedimentation rates have increased several fold during the past three decades in response to localized development. The magnitude of increased sedimentation was surprising given limited development within the basin: 0.12 to 0.68 buildings/ha in 2000 in those parts directly delivering sediment to the dated cores. Thus, the analysis illustrates the potential sensitivity of watersheds in the southern Appalachians to changes in land cover. An approach that combined geochemical fingerprinting with sediment mixing models was subsequently evaluated to determine its ability to accurately estimate the contribution of sediment from (1) major bedrock formations that underlie the watershed and (2) potential sources associated with four land cover categories. Sediment sources in both analyses proved difficult to geochemically fingerprint to greater than 90 percent accuracy using data on acid‐soluble metals and selected isotopes of lead (Pb). The relative contributions of sediment from delineated sources, estimated by the mixing models, generally corresponded with known temporal and spatial patterns of land cover. However, the models were plagued by two significant problems — the chemical alteration of sediments as they were transported through upland streams to depositional sites within the lake and the loss of elemental mass. Thus, future investigations using the fingerprinting approach in this area of intense weathering, and presumably others, will need to modify the existing methods to more accurately elucidate changes in sediment provenance related to development.     

Relation of length and sex to selenium concentrations in mosquitofish

Analysis of mosquitofish, Gambusia affinis, has proven useful for monitoring contaminant levels in aquatic biota; however, the small size of this species often requires the compositing of several fish to provide sufficient biomass for selenium analysis. Such composites have usually been obtained without considering the length and sex of the individual fish. The present study found significant differences in mean lengths and sex ratios of mosquitofish sampled with small-mesh dip nets from five sites close to each other in the San Joaquin Valley, California. To test the effect of these different sample characteristics, fish from each site were divided by sex into five size classes (<20, 20-30, 31-45, 46-60, and >60mm total length) before analysis for total selenium. Altogether, fish from the San Luis Drain and Kesterson Ponds 2 and 7 contained 65-360 microg g(-1) selenium (dry weight basis), or about 28- to 300-fold more than concentrations in fish of the same length and sex from the Volta Wasteway and Volta Pond 26. Except for females 31-45 mm long from the San Luis Drain that had higher concentrations than either smaller or larger females, selenium concentrations did not differ significantly among size classes. Although concentrations differed between sexes in samples from the San Luis Drain, Kesterson Pond 2, and Volta Pond 26, neither males nor females consistently had the higher concentrations. In the San Luis Drain, 20-30 and 31-45 mm long females had higher concentrations than did males of the same size classes; in Kesterson Pond 2 and Volta Pond 26, however, 20-30 mm long males had higher concentrations than did females of the same size class. Although no consistent patterns were observed, the occasional differences in selenium concentrations in fish of different length and sex indicate that these variables should be considered when surveys and monitoring studies are designed.     

Agriculture's share in the emission of trace gases affecting the climate and some cause-oriented proposals for sufficiently reducing this share

This paper discusses agriculture's share in the world-wide emissions of climate-affecting gases and in the global warming potential (GWP). Proposals also are presented to reduce these emissions adequately, using a cause-oriented approach. Largely due to the fertilization and cultivation of agriculture as well as the burning of biomass, agriculture has a very high share in the anthropogenic emissions of NH(3), N(2)O, CH(4) and CO at >95%, 81%, 70% and 52%, respectively, while its share in the NO(x) and CO(2) emissions is relatively small at 35% and 21%. The GWP of agriculture, based on annually 16.1 x 10(9) tons of CO(2), approaches 63% of the GWP of the energy sector or 80% of the GWP of its CO(2) emissions. At 34% and 32%, respectively, the main originators in the GWP of agriculture would seem to be CO(2) (changing land use) and CH(4) (animal husbandry/rice cropping/biomass burning) followed at 15% by NO(2) (technical and biological N fixation/(cultivation and recultivation/biomass burning) and 10% and 9% by CO and NO(x). The GWP of 3 German dairy cows corresponds with 13.2 tonnes CO(2) per year the GWP of two average German automobiles. However, the ozone-destroying effect of N(2)O and the climate-relevant effects of NH(3) are not yet included here. As with the therapy for other 'modern' boundary-crossing environmental damages, such as acidification or eutrophication, global climate change therapy likewise needs a therapy for the respective effects of reactive compounds of carbon, nitrogen, phosphorous, and sulfur also emitted by agriculture. Proposals for reducing these emissions within the agricultural sector include need-oriented plant, animal and human nutrition, more efficient external and internal nutrient recycling, the cessation of further clearing by burning, along with intensified afforestation mainly in the tropics, targeted measures to reduce nutrient losses/emissions, and measures for more efficient use of nutrients in plant, animal and human nutrition. These measures would at best result in reduced pollution of the global environment but not put it to an end. Decisive, therefore, is both the tolerable extent of mankind and its long-term sustainable way of life.     

The sensitivity of surface waters of Great Britain to acidification predicted from catchment characteristics

Using a combination of soil, land use and geological information, a map of Great Britain has been derived which indicates the sensitivity of surface waters to acidification. For the geological information, a slightly modified version of an available map was used which indicated the sensitivity of groundwaters to acidification. For soils, 1-km databases of soil information for England and Wales and for Scotland were employed to map the soil sensitivity as determined by buffering capacity. The derived soils map was modified to take account of agricultural liming in arable and managed grassland areas using the ITE Land Classification. The final map of surface water sensitivity was obtained by using a geographic information system overlay procedure which enabled each combination of soil and geology sensitivity to be uniquely defined. The final sensitivity classification was based upon expert knowledge and the experience of a similar sensitivity mapping exercise for Wales.     

Means to improve the effect of in situ bioremediation of contaminated soil: an overview of novel approaches

Different aspects of bacterial degradation of organic contaminants in soil, and how to improve the efficiency and reproducibility is discussed in this review. Although bioremediation in principle includes the use of any type of organism in improving the condition of a contaminated site, most commonly bacteria are the degraders and other organisms, such as soil animals or plant roots, play a role in dissemination of bacteria and, indirectly, plasmids between bacteria, and in providing nutrients and co-substrates for the bacteria active in the degradation process. There are a number of different procedures that have been tested more-or-less successfully in attempts to improve reliability, cost efficiency and speed of bioremediation. The methods range from minimal intervention, such as mere monitoring of intrinsic bioremediation, through in situ introduction of nutrients and/or bacterial inocula or improvement of physico-chemical conditions, all the way to excavation followed by on site or ex situ composting in its different varieties. In the past the rule has been that more intervention (leading to higher costs) has been more reliable, but novel ideas are continuously tried out, both as a means to come up with new truly functional applications and also as a line of studies in basic soil microbial ecology. Both approaches generate valuable information needed when predicting outcome of remediation activities, evaluating environmental risks, deciding on cleaning-up approaches, etc. The emphasis of this review is to discuss some of the novel methods for which the value has not been clearly shown, but that in our view merit continued studies and efforts to make them work, separately or in combination.     

Influence of ozone stress on growth processes, yields and grain quality characteristics among soybean cultivars

Field studies were conducted at USDA Beltsville Agricultural Research Center, Beltsville, Maryland, in 1984 and 1985 using open-top chambers to acquire information on the responses of 12 soybean (Glycine max L. Merr.) cultivars to O3 stress and to examine the interactions between maturity groups and O3 stress. Cultivars representing Groups III, IV, and V were exposed for approximately 3 months to charcoal-filtered air (CF) and nonfiltered air plus 40 nl litre(-1) O3 (NF + O3). Ozone was added 6 h d(-1), 5 d week(-1) for 13 weeks. The CF effectively reduced the accumulative oxidant exposure (AOX) to less than 1.0 microl litre(-1) h and the NF + O3 treatment approximately doubled the ambient AOX (16.7 microl litre(-1) h) to about 30 microl litre(-1) h. The AOX estimates the total O3 exposure above 30 nl litre(-1) during an entire growing season. Plant growth rates and relative growth rates were reduced by 17.0 and 14.4%, respectively, when averaged over cultivars. Based on growth rates, the Group III cultivars were the most affected by O3 stress. Averaged over cultivars, leaf expansion rates, leaf conductance, and transpiration rates were lower in the NF + O3 treatment compared to the CF control; however, wide variation was found with the stomatal results from field observations. Combined over years and cultivars, grain yield was reduced by an average of 12.5% by O3 stress with 3 of 12 cultivars showing significant reductions. Grain protein content was increased by 0.7% by O3 stress, but cultivar differences were equal to the differences caused by the O3 treatments. Grain oil content was unchanged by the O3 treatments. Group IV cultivars showed the greatest decrease in grain yield due to O3 stress. Multiple regression analyses were calculated using the difference between the CF and NF + O3 treatment as a measure of O3 stress. Significant positive relationships were found among net assimilation rates, plant growth rates, relative growth rates, and leaf expansion rates, which suggest that growth analysis characteristics would be useful in addition to yield in air pollution tolerance improvement studies with soybeans.     

Improvements of nano-SiO2 on sludge/fly ash mortar

Sewage sludge ash has been widely applied to cementitious materials. In this study, in order to determine effects of nano-SiO(2) additives on properties of sludge/fly ash mortar, different amounts of nano-SiO(2) were added to sludge/fly ash mortar specimens to investigate their physical properties and micro-structures. A water-binding ratio of 0.7 was assigned to the mix. Substitution amounts of 0%, 10%, 20%, and 30% of sludge/fly ash (1:1 ratio) were proposed. Moreover, 0%, 1%, 2%, and 3% of nano-SiO(2) was added to the mix. Tests, including SEM and compressive strength, were carried out on mortar specimens cured at 3, 7, and 28 days. Results showed that sludge/fly ash can make the crystals of cement hydration product finer. Moreover, crystals increased after nano-SiO(2) was added. Hence, nano-SiO(2) can improve the effects of sludge/fly ash on the hydration of mortar. Further, due to the low pozzolanic reaction active index of sludge ash, early compressive strengths of sludge/fly ash mortar were decreased. Yet, nano-SiO(2) could help produce hydration crystals, which implies that the addition of nano-SiO(2) to mortar can improve the influence of sludge/fly ash on the development of the early strength of the mortar.     

Development of a new quality fair access best value performance indicator (BVPI) for recycling services

Recycling schemes are being used worldwide to reduce the impact of municipal waste. Those using public funds are usually obliged to set performance indicators by which the standards of such schemes can be measured. In the UK, a set of statutory Best Value Performance Indicators (BVPI) must be reported annually, such as the Quality of Fair Access, which monitors the public's access to recycling facilities within 1000 m (known as BVPI 91). This work shows that BVPI 91, and performance indicators like it, quantify only very basic recycling services. A much more sensitive performance indicator is developed in this paper, labelled as the Maximum Practicable Recycling Rate Provision (MPRRP) achievable by a local authority. It indicates the percentage of local waste that could be reasonably recycled using the services provided, calculated on the basis of the average composition of the local waste, the local population coverage for collection of any materials, and nationally provided information stating how much of each material stream is generally suitable (practical) for recycling. Evidence for the usefulness of this new quantity is presented. Although this paper refers a particular performance indicator in the UK, its findings are applicable to all urban areas worldwide needing to monitor recycling service. Furthermore, the MPRRP could be used for planning purposes, and for determining the level of performance of an existing service, by comparing its predicted recycling rate to that actually obtained. Further work is now being carried out on this.     

Characterization of food waste and bulking agents for composting

The characterization of food waste (FW) and locally available bulking agents (BA) are a prerequisite to optimizing compost recipes. This study measured the variation in FW characteristics (pH, dry matter (DM), carbon (C), wet bulk density and Total Kjeldahl Nitrogen (TKN)) produced by a restaurant and a community kitchen in downtown Montreal, Canada from May to August 2004. The project also measured the mass of FW produced by another restaurant and a group of 20-48 households, from June to August 2004. Locally available BA (hay, straw, pine wood shavings, cardboard, left over cattle feed and wheat residue pellets) were also characterized to formulate composting recipes based on the FW characteristics observed during a period representative of winter and summer conditions. Residential and restaurant FW characteristics varied significantly over the summer months, although the mass produced remained constant at 0.61 and 0.56 kg capita(-1)day(-1), respectively. In addition, the number of customers served by the restaurant increased by nearly 50% from June to August. The BA with the highest moisture adsorption capacity was found to be the wheat residue pellets, followed by chopped straw. Wheat residue pellets, chopped hay and left over cattle feed all presented a balanced C/N ratio. Wheat residue pellets and wheat straw, chopped hay and cardboard demonstrated neutral pH values. Based on the variable FW characteristics and monthly production rates, the formulation of recipes indicates that compost facilities must be flexible enough to handle seasonal variations of as much as 50% by volume.