Estrogenic activity removal of 17beta-estradiol by ozonation and identification of by-products

This work investigated the degradation of a natural estrogen (17beta-estradiol) and the removal of estrogenic activity by the ozonation process in three different pHs (3, 7 and 11). A recombinant yeast assay (YES assay) was employed to determine estrogenic activity of the ozonized samples and of the by-products formed during the ozonation. Ozonation was very efficient for the removal of 17beta-estradiol in aqueous solutions. High removals (>99%) were achieved with low ozone dosages in the three different pHs. Several by-products were formed during the ozonation of 17beta-estradiol. However, only a few compounds could be identified and confirmed. Different by-products are formed at different pHs, which is probably due to different chemical pathways and different oxidants (O(3) and OH radical). The by-products formed at pH 11 were 10epsilon-17beta-dihydroxy-1, 4-estradieno-3-one (DEO) and 2-hydroxyestradiol, which were not formed in pH 3. Only testosterone could be observed in pH 3, whereas at pH 7 all three by-products were found. At pH 7 and 11 the applied ozone dosages were not enough to remove all the estrogenicity from samples, even though the 17beta-estradiol residual concentration for these two pHs was lower than at pH 3. Higher estrogenicity was detected at pH 11. An explanation to this fact may be that oxidation via OH radical forms more by-products with estrogenic activity. Probably, the formation of 2-hydroxyestradiol at pHs 7 and 11 is contributing to the residual estrogenicity of samples ozonized at these pHs. In this work, complete removal of estrogenic activity was only obtained at pH 3.     

Biodegradability and ecotoxicity of amine oxide based surfactants

The aerobic and anaerobic biodegradability as well as the aquatic toxicity of two fatty amine oxides and one fatty amido amine oxide were investigated. Aerobic biodegradation was evaluated using the CO(2) headspace test (ISO 14593) and biodegradation under anaerobic conditions was assessed employing a standardised batch test. The three amine oxide based surfactants tested were readily biodegradable under aerobic conditions but only the alkyl amido amine oxide was found to be easily biodegradable under anaerobic conditions. Toxicity to Photobacterium phosphoreum and Daphnia magna was evaluated. Bacteria (EC(50) from 0.11 to 11 mg l(-1)) proved to be more sensitive to the toxic effects of the amine oxide based surfactants than crustacea (IC(50) from 6.8 to 45 mg l(-1)). The fatty amido amine oxide showed the lowest aquatic toxicity.     

Landfill leachate enhances fermentative hydrogen production from glucose and sugarcane processing derivatives

Fermentation can use renewable raw materials as substrate, which makes it a sustainable method to obtain H₂. This study evaluates H₂ production by a mixed culture from substrates such as glucose and derivatives from sugarcane processing (sucrose, molasses, and vinasse) combined with landfill leachate. The leachate alone was not a suitable substrate for biohydrogen production. However, leachate blended with glucose, sucrose, molasses, or vinasse increased the H₂ production rate by 2.0-, 2.8-, 4.6-, and 0.5-fold, respectively, as compared with the substrates without the leachate. Determination of metals (Cu, Cd, Pb, Hg, Ni, and Fe) at the beginning and at the end of the fermentative assays showed how they were consumed during the fermentation and demonstrated improved H₂ production. During fermentation, Cu, Fe, and Cd were the most consumed leachate metals. The best substrate combination to produce H₂ was molasses and leachate, which gave high volumetric productivity—469 ml H₂/l h. However, addition of the leachate to the substrates stimulated lactic acid formation pathways, which lowered the H₂ yield. The use of leachate combined with sugarcane processing derivatives as substrates could add value to the leachate and reduce its polluting power, generating a clean energy source from renewable raw materials.     

A Solvent-Free Approach for Production of Films from Pectin and Fungal Biomass

Self-binding ability of the pectin molecules was used to produce pectin films using the compression molding technique, as an alternative method to the high energy-demanding and solvent-using casting technique. Moreover, incorporation of fungal biomass and its effects on the properties of the films was studied. Pectin powder plasticized with 30% glycerol was subjected to heat compression molding (120 °C, 1.33 MPa, 10 min) yielding pectin films with tensile strength and elongation at break of 15.7 MPa and 5.5%, respectively. The filamentous fungus Rhizopus oryzae was cultivated using the water-soluble nutrients obtained from citrus waste and yielded a biomass containing 31% proteins and 20% lipids. Comparatively, the same strain was cultivated in a semi-synthetic medium resulting in a biomass with higher protein (60%) and lower lipid content (10%). SEM images showed addition of biomass yielded films with less debris compared to the pectin films. Incorporation of the low protein content biomass up to 15% did not significantly reduce the mechanical strength of the pectin films. In contrast, addition of protein-rich biomass (up to 20%) enhanced the tensile strength of the films (16.1–19.3 MPa). Lastly, the fungal biomass reduced the water vapor permeability of the pectin films.     

Baked Foams Based on Cassava Starch Coated with Polyvinyl Alcohol with a Higher Degree of Hydrolysis

The aims of this work were to produce trays based on cassava starch, coated with polyvinyl alcohol (PVA) with a higher degree of hydrolysis (98%), and to study the effects of the coating on the mechanical and water sorption properties of the trays. Two types of PVA were tested: SELVOL? 325 (degree of polymerization?=?1000–1500) and SELVOL? 107 (degree of polymerization?=?350–650). A decrease in the water absorption capacity of 50% was observed when the coated samples were compared with the control sample after 30 min of immersion in water. It was observed in both coated samples a reduction of the initial rate of water adsorption sorption and a decrease in hydrophilicity compared with the control sample. Tensile strength and elongation were increased with application of the coatings. The use of the two types of PVA resulted in materials with similar mechanical and water sorption properties.     

Environmental Impact and Sustainable Development: An Analysis in the Context of Standards ISO 9001, ISO 14001, and OHSAS 18001

In this study, we seek to verify the contributions made by three international standards to efforts by eight companies to reduce their environmental impacts and move toward sustainable development. The standards considered in this article are the International Organization for Standardization's (ISO) 9001 (quality), ISO 14001 (environmental management systems), and the Occupational Health and Safety Assessment Series (OHSAS) 18001. The eight companies analyzed for this study are located in the state of Rio Grande do Sul in Brazil. As part of this work, the authors generated a proposed sustainable positioning matrix and placed each company within one of four quadrants—economic approach, environmental approach, social approach, and sustainability approach—derived from the context of the Triple Bottom Line (Elkington, 2004 ).     

First inter-laboratory comparison exercise for the determination of anticancer drugs in aqueous samples

The results of an inter-laboratory comparison exercise to determine cytostatic anticancer drug residues in surface water, hospital wastewater and wastewater treatment plant effluent are reported. To obtain a critical number of participants, an invitation was sent out to potential laboratories identified to have the necessary knowledge and instrumentation. Nine laboratories worldwide confirmed their participation in the exercise. The compounds selected (based on the extent of use and laboratories capabilities) included cyclophosphamide, ifosfamide, 5-fluorouracil, gemcitabine, etoposide, methotrexate and cisplatinum. Samples of spiked waste (hospital and wastewater treatment plant effluent) and surface water, and additional non-spiked hospital wastewater, were prepared by the organising laboratory (Jo?ef Stefan Institute) and sent out to each participant partner for analysis. All analytical methods included solid phase extraction (SPE) and the use of surrogate/internal standards for quantification. Chemical analysis was performed using either liquid or gas chromatography mass (MS) or tandem mass (MS/MS) spectrometry. Cisplatinum was determined using inductively coupled plasma mass spectrometry (ICP-MS). A required minimum contribution of five laboratories meant that only cyclophosphamide, ifosfamide, methotrexate and etoposide could be included in the statistical evaluation. z-score and Q test revealed 3 and 4 outliers using classical and robust approach, respectively. The smallest absolute differences between the spiked values and the measured values were observed in the surface water matrix. The highest within-laboratory repeatability was observed for methotrexate in all three matrices (CV?≤?12 %). Overall, inter-laboratory reproducibility was poor for all compounds and matrices (CV 27–143 %) with the only exception being methotrexate measured in the spiked hospital wastewater (CV?=?8 %). Random and total errors were identified by means of Youden plots.     

Enrichment of trace elements in the clay size fraction of mining soils

Reactive waste dumps with sulfide minerals promote acid mine drainage (AMD), which results in water and soil contamination by metals and metalloids. In these systems, contamination is regulated by many factors, such as mineralogical composition of soil and the presence of sorption sites on specific mineral phases. So, the present study dedicates itself to understanding the distribution of trace elements in different size fractions (<2-mm and <2-μm fractions) of mining soils and to evaluate the relationship between chemical and mineralogical composition. Cerdeirinha and Penedono, located in Portugal, were the waste dumps under study. The results revealed that the two waste dumps have high degree of contamination by metals and arsenic and that these elements are concentrated in the clay size fraction. Hence, the higher degree of contamination by toxic elements, especially arsenic in Penedono as well as the role of clay minerals, jarosite, and goethite in retaining trace elements has management implications. Such information must be carefully thought in the rehabilitation projects to be planned for both waste dumps.     

Biodegradability of the anticancer drug etoposide and identification of the transformation products

Etoposide susceptibility to microbiological breakdown was studied in a batch biotransformation system, in the presence or absence of artificial wastewater containing nutrients, salts and activated sludge at two concentration levels. The primary focus of the present study was to study etoposide transformation products by ultra-high performance liquid chromatography coupled to high-resolution hybrid quadrupole-Orbitrap tandem mass spectrometry (MS/MS). Data-dependent experiments combining full-scan MS data with product ion spectra were acquired to identify the molecular ions of etoposide transformation products, to propose the molecular formulae and to elucidate their chemical structures. Due to the complexity of the matrix, visual inspection of the chromatograms showed no clear differences between the controls and the treated samples. Therefore, the software package MZmine was used to facilitate the identification of the transformation products and speed up the data analysis. In total, we propose five transformation products; among them, four are described as etoposide transformation products for the first time. Even though the chemical structures of these new compounds cannot be confirmed due to the lack of standards, their molecular formulae can be used to target them in monitoring studies.