The influence of pH on cadmium toxicity to the green alga Stichococcus bacillaris and on the cadmium forms present in the culture medium

Cadmium toxicity to the green alga Stichococcus bacillaris was investigated in media of pH 3-9. A significant decrease of cadmium toxicity occurred in both the acidic and alkaline ranges of pH. In media of pH 3 and 9, cadmium did not affect the dry mass content substantially. Maximum toxicity of cadmium was noticed at pH 6-7. Voltametric investigations showed a significant effect of pH on electrochemically measured cadmium content in the culture media. Hydrolysis of the medium components and formation of cadmium complexes with OH(-) ions caused a considerable decrease in amounts of electrochemically measured cadmium in the alkaline range of pH.     

钴（Ⅱ）－过氧化氢－苯基荧光酮体系催化光度法测定痕量钴的研究

本文研究了钴（Ⅱ）催化过氧化氢氧化苯基荧光酮的褪色反应，测定了反应级数和表观活化能，建立了测定痕量地的新方法。２５℃时本法检出限为２９×１０－１３ｇ／ｍｌ，线性范围为０．０４～２ｎｇ／１０ｍｌ，催化反应表观活化能为５６．１５ＫＪ／ｍｏｌ。该方法己用于维生素Ｂ１２、人发和茶叶中痕量钴的测定．结果满意，相对标准偏差为２．４～３．４％。     

Air Pollution in Singapore: Its Multielemental Aspect as Measured by Nuclear Analytical Techniques

Aerosol samples were collected in 1994 in Singapore on two occasions: once in June during the normal meteorological conditions and later in October during a long haze period caused by the heavy forest fire in Indonesia. Filtration and impaction collection methods were used simultaneously so that detailed elemental analysis of bulk as well as of different size fractions could be performed. Accelerator based nuclear analytical techniques such as Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and Nuclear Microscopy (NM) were used for analysis. These techniques are fast, truly multielemental and perfectly suited for routine analysis of a large number of aerosol samples. Typically all samples were analysed for the following 24 elements: Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Mn, Cr, Fe, Co, Ni, Cu, Zn, Ga, As, Br, Rb, Sr and Pb. Detection limits for bulk analysis were generally below ng/m3 and for single particle analysis absolute detectable mass was approximately 10-17 g. Additionally, trace elements such as Cd, Sn, Sb and Ba whose characteristic X-ray lines were normally "obscured" by the lines of other more abundant elements, were detected when analysing by nuclear microscope in single particle mode.Judging by the average concentrations of lead and sulphur which are good indicators of industrial component of air pollution the situation in Singapore is satisfactory. Pb was typically found in concentrations of 5 to 50 ng/m3 and sulphur in concentrations of 1 to 2 µg/m3. These concentrations are well below limits set by the World Health Organisation (1500 ng/m3 and 40 µg/m3, respectively). On the other hand during the haze period the average concentrations of elements like S, K, Ti, V, Mn, Ni, As and Pb were found to be 3 to 6 times higher than usual. Results are presented and discussed.     

Laboratory and Field Assessment of Arsenic Testing Field Kits in Bangladesh and West Bengal, India

High concentrations of arsenic in ground waters in West Bengal and Bangladeshhave become a major cause for concern in recent years. Given the enormity and the severity of the problemof arsenic poisoning, a task of evaluating the commercially available arsenic detection field kits for their capabilities was undertaken. In the light of the findings, generic specificationswere recommended which could form the basis forindigenous manufacture of these kits in the arsenic affected countries. This article presents the results of the laboratory and fieldevaluation conducted in Bangladesh and West Bengalof five arsenic testing field kits. The salient features of the kits, their merits and limitationshave been brought out. Based on the criteria of kitdesign, quality of chemicals used, colourcomparator charts, detection range, time required for analysis, cost etc., a comparative ranking ofthe kits has been made to facilitate the choice of the kit to meet specific requirements.     

Recycling of petroleum-contaminated sand

The environmental impact of using petroleum-contaminated sand (PCS) as a substitute in asphalt paving mixtures was examined. An appreciable component of PCS is oily sludge, which is found as the dregs in oil storage tanks and is also produced as a result of oil spills on clean sand. The current method for the disposal of oily sludge is land farming. However, this method has not been successful as an oil content of < 1% w/w is required, and difficulty was encountered in reaching this target. The reuse of the sludge in asphalt paving mixtures was therefore considered as an alternative. Standard tests and environmental studies were conducted to establish the integrity of the materials containing the recycled sludge. These included physical and chemical characterization of the sludge itself, and an assessment of the mechanical properties of materials containing 0%, 5%, 22% and 50% oily sludge. The blended mixtures were subjected to special tests, such as Marshall testing and the determination of stability and flow properties. The experimental results indicated that mixtures containing up to 22% oily sludge could meet the necessary criteria for a specific asphalt concrete wearing course or bituminous base course. To maximize the assay from the recycled material, the environmental assessment was restricted to the 50% oily sludge mixture. Leachates associated with this particular mixture were assayed for total organic residue and certain hazardous metal contaminants. The results revealed that the organics were negligible, and the concentrations of the metals were not significant. Thus, no adverse environmental impact should be anticipated from the use of the recycled product. Our research showed that the disposal of oily sludge in asphalt paving mixtures could possibly yield considerable savings per tonne of asphalt concrete, and concurrently minimize any direct impact on the environment.     

Monitoring Air Quality in Mountains: Designing an Effective Network

A quantitatively robust yet parsimonious air-quality monitoring network in mountainous regions requires special attention to relevant spatial and temporal scales of measurement and inference. The design of monitoring networks should focus on the objectives required by public agencies, namely: 1) determine if some threshold has been exceeded (e.g., for regulatory purposes), and 2) identify spatial patterns and temporal trends (e.g., to protect natural resources). A short-term, multi-scale assessment to quantify spatial variability in air quality is a valuable asset in designing a network, in conjunction with an evaluation of existing data and simulation-model output. A recent assessment in Washington state (USA) quantified spatial variability in tropospheric ozone distribution ranging from a single watershed to the western third of the state. Spatial and temporal coherence in ozone exposure modified by predictable elevational relationships ( 1.3 ppbv ozone per 100 m elevation gain) extends from urban areas to the crest of the Cascade Range. This suggests that a sparse network of permanent analyzers is sufficient at all spatial scales, with the option of periodic intensive measurements to validate network design. It is imperative that agencies cooperate in the design of monitoring networks in mountainous regions to optimize data collection and financial efficiencies.     

Concentration and Distribution of Persistent Organic Pollutants (POPs) in Harbour Dredging Sediments: A Pilot Study Using a Statistical Approach for a More Efficient Characterisation and Management

The Italian guidelines concerning the dumping of dredgingmaterials implies chemical, physical and microbiologicalcharacterisation of dumping sediments collected through aspecific sampling strategy.POP's such as PCB's and organochlorine pesticides, areconsidered as priority pollutants in all the InternationalConventions for the protection of the marine environment, inconsequence of their persistence, toxicity and bioaccumulation capacity.In the present article the concentrations and distribution ofPCB's and organochlorine pesticides in dredging sediments ofPiombino harbour (northern Thyrrenian sea) were investigates.The results showed high POP's concentrations in all the studiedareas. The maximum values were: 3.94 mg kg^-1 dry weight for PCB's(IUPAC Nos. 28; 52; 101, 118; 137; 153; 180; 209); 2.04 mg kg^-1 d.w.for HCH's (-, -, - and -hexachlorocyclohexane isomers); 0.28 mg kg^-1 d.w. for DD's (DDT + DDE + DDD).Subsequently, the data related to each pollutant were treatedwith statistical tests, in order to verify how well the samplingstrategy is able to represent the distribution of contaminantsin the dredging area. Finally, management strategies werederived for the studied dredging sediments.     

Chlorinated Hydrocarbons in Livers of American Mink (Mustela vison) and River Otter (Lutra canadensis) from the Columbia and Fraser River Basins, 1990–1992

We investigated chlorinated hydrocarbon contaminants in aquatic mustelid species on the Fraser and Columbia Rivers of northwestern North America. Carcasses of river otter (Lutra canadensis) (N=24) and mink (Mustela vison) (N=34) were obtained from commercial trappers during the winters of 1990–91 and 1991–92. Pooled liver samples were analyzed for organochlorine pesticides, polychlorinated biphenyls (PCBs), including non-ortho congeners, polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). Most samples contained detectable concentrations of DDE, PCBs, although there was substantial variability in patterns and trends among neighboring samples. Concentrations of DDE were in some mink and several otter samples from the lower Columbia River elevated (to 4700 g/kg wet weight); excluding one mink sample from the Wenatchee area, mean DDE levels generally decreased between 1978–79 and 1990–92. PCBs were present in all samples. PCB concentrations in otter livers collected from the lower Columbia were ten-fold lower than measured a decade previously; nevertheless, a sample taken near Portland had a mean concentration of 1500 g/kg, within a range of concentrations associated with reproductive effects in captive mink. Concentrations of 2,3,7,8-TCDD and TCDF were generally below detection limits, except for one otter collected near a pulp mill at Castlegar, on the upper Columbia, with 11 ng TCDD/kg in liver. Elevated concentrations of higher chlorinated PCDD/Fs, probably resulting from use of chlorophenolic wood preservatives, were found in both species; one otter sample from the lower Columbia had 2200 ng OCDD/kg. International TCDD toxic equivalent levels in mink (31 ng/kg) and otter (93 ng/kg) from the lower Columbia River approached toxicity thresholds for effects on reproduction in ranch mink.     

Reduction and avoidance of lubricant mist demands an integrated assessment approach

A case study to identify major factors for lubricant mist exposure covered 15 metal machining sites. The investigation included milling, turning, drilling and grinding applications. Systematic analysis considered all relevant data concerning the machine tool, the lubricant and the suction plant. The efficiency of the implemented maintenance program at the installed filter systems was checked by concentration measurements immediately before and after service. All performed measurements of lubricant aerosol and vapor loads upstream and downstream of the installed filter systems were carried out according to VDI 2066 and BIA 3110, respectively. The selection criteria for the sites to be investigated, the systematic nature of the data acquisition and the procedure of the analysis are demonstrated in detail by performing comparisons between selected applications using emulsions and those employing straight oil for lubrication. The results of the study identify recirculation of ventilated air as the major source of workplace exposure to airborne lubricant emissions. More than 60% of the demisters investigated emit air at total lubricant loads (aerosols and vapor) above the limit of 20 mg m-3 at any time of operation; which also means immediately after service. A common reason for exceeded aerosol loads in recirculated air is e.g. the fact that the type of filter system applied is often not suitable for the separation problem. Loads of lubricant vapor are usually higher at the processes which use water emulsions as lubricant. In a quarter of the cases the limits were exceeded solely due to high vapor loads even immediately after service. The exposure can be reduced by replacing the lubricant, installation of a vapor separation plant or avoiding air recirculation. Maintenance time of the demisting system and aerosol separation efficiency of state-of-the-art demisting systems can be expanded by implementation of enhanced preliminary filter stages. This study confirms that appropriate service measures lower both aerosol emissions and lubricant vapor concentrations due to the reduction of exposed oil-wetted surfaces. The performed measurements show no significant relationship between loads of airborne lubricants and the type of machining process. Therefore, investigations at a much more detailed level have to be performed. However, the individual assessment of any workplace due to the complex situation remains essential.     

State estimation in wastewater engineering: Application to an anaerobic process

The use of an extended Kalman filter for state estimation in biological wastewater treatment processes is discussed. The application of the technique requires an adequate mechanistic dynamic model and the identification and modelling of the major sources of stochastic disturbances in the process. The filter allows the on-line tracking of process variables which are not directly measurable. The use of an extended Kalman filter is illustrated through a simulated application to a high rate anaerobic wastewater treatment process.