Dilution-based emissions sampling from stationary sources: Part 1--Compact sampler methodology and performance

This paper presents the design and performance of a compact dilution sampler (CDS) for characterizing fine particle emissions from stationary sources. The sampler is described, along with the methodology adopted for its use. Dilution sampling has a number of advantages, including source emissions that are measured under conditions simulating stack gas entry and mixing in the ambient atmosphere. This is particularly important for characterizing the semivolatile species in effluents as a part of particulate emissions. The CDS characteristics and performance are given, along with sampling methodology. The CDS was compared with a reference dilution sampler. The results indicate that the two designs are comparable for tests on gas-fired units and a diesel electrical generator. The performance data indicate that lower detection limits can be achieved relative to current regulatory methods for particulate emissions. Test data for the fine particulate matter (PM2.5) emissions are provided for comparison with U.S. Environment Protection Agency (EPA) Conditional Test Method 040 for filterable particulate matter (FPM) and the EPA Method 202 for condensable particulate matter. This comparison showed important differences between methods, depending on whether a comparison is done between in situ FPM determinations or the sum of such values with condensable PM from liquid filled impingers chilled in an ice bath. These differences are interpretable in the light of semivolatile material present in the stack effluent and, in some cases, differences in detection and quantification limits. Determination of emissions from combustors using liquid fuels can be readily achieved using 1-hr sampling with the CDS. Emissions from gasfired combustors are very low, requiring careful attention to sample volumes. Sampling volumes corresponding with 6-hr operation were used for the combined mass and broad chemical speciation. Particular attention to dilution sampler operation with clean dilution air also is essential for gas-fired sources.     

Particulate emissions from U.S. Department of Defense artillery backblast testing

There is a dearth of information on dust emissions from sources that are unique to the U.S. Department of Defense testing and training activities. However, accurate emissions factors are needed for these sources so that military installations can prepare accurate particulate matter (PM) emission inventories. One such source, coarse and fine PM (PM10 and PM2.5) emissions from artillery backblast testing on improved gun positions, was characterized at the Yuma Proving Ground near Yuma, AZ, in October 2005. Fugitive emissions are created by the shockwave from artillery pieces, which ejects dust from the surface on which the artillery is resting. Other contributions of PM can be attributed to the combustion of the propellants. For a 155-mm howitzer firing a range of propellant charges or zones, amounts of emitted PM10 ranged from -19 g of PM10 per firing event for a zone 1 charge to 92 g of PM10 per firing event for a zone 5. The corresponding rates for PM2.5 were approximately 9 g of PM2.5 and 49 g of PM2.5 per firing. The average measured emission rates for PM1o and PM2.5 appear to scale with the zone charge value. The measurements show that the estimated annual contributions of PM10 (52.2 t) and PM2.5 (28.5 t) from artillery backblast are insignificant in the context of the 2002 U.S. Environment Protection Agency (EPA) PM emission inventory. Using national-level activity data for artillery fire, the most conservative estimate is that backblast would contribute the equivalent of 5 x 10(-4) % and 1.6 x 10(-3)% of the annual total PM10 and PM2.5 fugitive dust contributions, respectively, based on 2002 EPA inventory data.     

Growing hot pepper for cabbage looper, Trichopulsia ni (Hübner) and spider mite, Tetranychus urticae (Koch) control

With the public perception that synthetic pesticides leave harmful residues in crop produce for human consumption, there has been increased interest in using natural products for pest control. The potential of using fruit extracts of hot pepper for controlling the cabbage looper, Trichopulsia ni (Hübner) and spider mite, Tetranychus urticae Koch is explored in this investigation. Crude extracts from fruits of Capsicum chinense, C. frutescens, C. baccatum, and C. annuum, were prepared and tested under laboratory conditions for their insecticidal and acaricidal performance. Mortality was greatest (94%) when fruit extract of accession PI-593566 (C. annuum) was sprayed on larvae of the cabbage looper, while crude extracts of accessions PI-241675 (C. frutescens) and PI-310488 (C. annuum) were repellent to the spider mite. We investigated differences in chemical composition of the crude fruit extracts that may explain the observed differences in mortality and repellency between accessions. Gas Chromatography-Mass Spectrometry spectrometric analysis revealed that capsaicin and dihydrocapsaicin, the pungent components of pepper fruit, were not correlated with toxicity or repellency, indicating that the two capsaicinoids are not likely related to the efficacy of pepper fruit extracts. Major compounds in hot pepper fruit extracts were detected and identified as pentadecanoic acid methyl ester, hexadecanoic acid methyl ester, and octadecanoic acid methyl ester. Spectrometric analysis and toxicity to cabbage looper larvae revealed that pentadecanoic acid methyl ester is likely related to cabbage looper mortality. However, the concentration of pentadecanoic acid methyl ester in some accessions was insufficient to explain the observed mortality of cabbage looper and repellency of spider mite. Fruit extracts of accessions PI-593566 (C. annuum) and PI-241675 (C. frutescens) could be useful for managing populations of cabbage loopers and spider mites, which could reduce reliance on synthetic pesticides. Further study is needed to investigate performance of hot pepper extracts under ultra-violet light and field conditions.     

Effects of inert dust on olive (<Emphasis Type="Italic">Olea europaea</Emphasis> L.) leaf physiological parameters

BACKGROUND: Cement factories are major pollutants for the surrounding areas. Inert dust deposition has been found to affect photosynthesis, stomatal functioning and productivity. Very few studies have been conducted on the effects of cement kiln dust on the physiology of perennial fruit crops. Our goal was to study some cement dust effects on olive leaf physiology.effects on olive leaf physiology. On METHODS: Cement kiln dust has been applied periodically since April 2003 onto olive leaves. Cement dust accumulation and various leaf physiological parameters were evaluated early in July 2003. Measurements were also taken on olive trees close to the cement factory. RESULTS: Leaf dry matter content and specific leaf weight increased with leaf age and dust content. Cement dust decreased leaf total chlorophyll content and chlorophyll a/chlorophyll b ratio. As a result, photosynthetic rate and quantum yield decreased. In addition, transpiration rate slightly decreased, stomatal conductance to H2O and CO2 movement decreased, internal CO2 concentration remained constant and leaf temperature increased. DISCUSSION: The changes in chlorophyll are possibly due to shading and/or photosystem damage. The changes in stomatal functioning were possibly due to dust accumulation between the peltates or othe effects on stomata. CONCLUSIONS: Dust (in this case from a cement kiln) seems to cause substantial changes to leaf physiology, possibly leading to reduced olive productivity. RECOMMENDATIONS: Avoidance of air contamination from cement factories by using available technology should be examined together with any possible methodologies to reduce plant tissue contamination from cement dust. PERSPECTIVES: Longterm effects of dust (from cement kiln or other sources) on olive leaf, plant productivity and nutritional quality of edible parts could be studied for conclusive results on dust contamination effects to perennial crops.     

Thermal terrain modeling of spatial objects, a tool for environmental and climatic change assessment

The aim of the current research effort is to include biophysical multi-temporal data and more specifically land surface temperature (LST) in the terrain modeling process that traditionally was based only on digital elevation data processing. The terrain partition framework (spatial objects) is defined by the borderlines of prefecture authorities of Greece. Each object is represented by a set of attributes derived from the digital elevation data, and objects are organized into clusters on the basis of their terrain dependent representation. Finally, the terrain is segmented to regions on the basis of the multi-temporal LST data, each region presenting a different thermal signature. The thermal regions are used in the spatial objects parametric representation and a new index is devised (LST climatic index) expressing the biophysical suitability of spatial objects at moderate resolution scale.     

Trace metal dynamics in fishes from the southwest coast of India

The concentration of Fe, Co, Ni, Cu, Zn, Cd, and Pb in the muscle tissue of marine fishes like Lates calcarifer, Nemipterus japonicus, Caranx melampygus, Rastrelliger kanagurta, and Cyanoglossus macrostomus was estimated from samples collected in the continental shelf waters off Kochi and Mangalore on southwest coast of India. Species-specific and spatially heterogeneous patterns of tissue metals loads were apparent within the pelagic and demersal fish species for the two regions. The concentration ranges of Fe (541.60 to 649.60 ppm), Ni (12.12 to 13.92 ppm), and Cu (3.09 to 3.62 ppm) were higher in the demersal species C. melampygus, whereas Co (9.10 to 11.80 ppm) and Zn (79.30 to 84.30 ppm) were higher in the pelagic species L. calcarifer and Cd (4.35 to 6.38 ppm) were higher in the demersal species N. japonicus, possibly due to enhanced bioavailability of these metals from ecological processes associated with upwelling during the summer monsoon. The fish species showed a great capacity to accumulate metals, with highest bioaccumulation for the essential element iron and lowest bioaccumulation for the non-essential element lead. Among the demersal species, C. melampygus and N. japonicus had high concentration factors for the metals Fe (280,268 to 322,808), Ni (88,252 to 96,891), Cu (2,351 to 2,600), and Cd (29,637 to 32,404). In contrast, the pelagic species L. calcarifer and R. kanagurta had high concentration factors for the metals Zn (40,812 to 46,892), Co (280,285 to 423,037), and Pb (854 to 1,404).     

Utilizing Successive Linearization Optimization to Control the Saltwater Intrusion Phenomenon in Unconfined Coastal Aquifers in Crete,Greece

In the present work, a simulation-optimization method is employed in order to manage saltwater intrusion in two unconfined coastal aquifers in Crete, Greece. The optimization formulation seeks to maximize groundwater withdrawal rates while maintaining the saltwater intrusion front at the current location or inhibiting it at locations closer to the coast. A combination of a groundwater flow model (MODFLOW) with the Ghyben-Herzberg saltwater front approximation and a sequential implementation of the Simplex algorithm (GWM) are employed. The results show that under the current pumping strategies, the saltwater intrusion front will continue to move inland, posing a serious threat to the groundwater quality of these regions. Optimal groundwater withdrawal scenarios that take into consideration the water needs of the local communities and environmental concerns are presented and discussed. In both case studies, significant reductions in pumping are required in order for the saltwater intrusion front to retract closer to the shoreline.