Concentration of LAS and boron in the Itter. Comparison of measured data with results obtained by simulation with the GREAT-ER software

The GREAT-ER software was used to calculate linear alkylbenzene sulphonate [LAS] and boron concentrations in the Itter stream in North Rhine-Westfalia, Germany. The aim was to investigate the predictive strength of this newly developed tool and to compare its results to measured data. Substance-specific input data which were used in this scenario were partly generic (e.g. LAS and sodium perborate tetrahydrate consumption figures for Germany) and partly (site-)specific data (e.g. half-life time for LAS elimination). The comparison with the measured data reveals that the model predictions for LAS and boron are correct at least within a factor of two, only if generic German consumption data is applied. By using refined input data, the accuracy can be increased further.     

Ash from the combustion of wood treated with inorganic wood preservatives: Element composition and leaching

Wood samples impregnated with inorganic wood preservatives containing the elements arsenic, boron, chromium, copper, fluorine, and/or zinc were burned in a furnace. Three different kinds of ash were collected: furnace, boiler, and so-called fly ash. Analyses showed that the ash contained large amounts of elements originating from the inorganic wood preservatives. Further interest was focused on the leachability of the above-mentioned elements. For this purpose a laboratory batch leaching test according to the German Standard DIN 38 414 part 4 was chosen. The results indicate that the leachability is in a range where the release of these elements to the environment from deposited ash can be considered as detrimental.     

The SeKT joint research project: definition of reference conditions, control sediments and toxicity thresholds for limnic sediment contact tests

- In current biotest approaches, intact organisms or in vitro systems are exposed to sediments using different exposure scenarios. The most important issue in sediment toxicity testing protocols is the question which test phase (solid or liquid) should be used. Whole-sediment exposure protocols represent the most realistic scenario to simulate in situ exposure conditions in the laboratory. However, until now there is no agreement in how to acquire and to evaluate the data of the various available sediment contact assays. The SeKT joint research project was initiated with the aim to compare recently developed sediment contact assays by addressing reference conditions, control sediments and toxicity thresholds for limnic sediment contact tests.     

Modelling of sequential groundwater treatment with zero valent iron and granular activated carbon

Multiple contaminant mixtures in groundwater may not efficiently be treated by a single technology if contaminants possess rather different properties with respect to sorptivity, solubility, and degradation potential. An obvious choice is to use sequenced units of the generally accepted treatment materials zero valent iron (ZVI) and granular activated carbon (GAC). However, as the results of this modelling study suggest, the required dimensions of both reactor units may strongly differ from those expected on the grounds of a contaminant-specific design. This is revealed by performing an analysis for a broad spectrum of design alternatives through numerical experiments for selected patterns of contaminant mixtures consisting of monochlorobenzene, tetrachloroethylene, trichloroethylene (TCE), cis-1,2-dichloroethylene (cis-DCE), and vinyl chloride (VC). It is shown that efficient treatment can be achieved only if competitive sorption effects in the GAC unit as well as the formation of intermediate products in the ZVI unit are carefully taken into account. Cost-optimal designs turned out to vary extremely depending on the prevailing conditions concerning contaminant concentrations, branching ratios, and unit costs of both reactor materials. Where VC is the critical contaminant, due to high initial concentration or extensive production as an intermediate, two options are cost-effective: an oversized ZVI unit with an oversized GAC unit or a pure GAC reactor.     

Laboratory evaluation of thermophilic-anaerobic digestion to produce Class A biosolids. 1. Stabilization performance of a continuous-flow reactor at low residence time.

There is increasing interest in the United States in producing biosolids from municipal wastewater treatment that meet the criteria for Class A designation established by the U.S. Environmental Protection Agency. Class A biosolids are intended to be free of pathogens and also must meet requirements for reduction of the vector-attraction potential associated with untreated sludge. High-temperature processes are considered to produce Class A biosolids if the combination of operating temperature and treatment time exceeds minimum criteria, but this option is not applicable to mixed, continuous-flow reactors. Such reactors, or any combination of reactors that does not meet the holding time requirement at a specific temperature, must be demonstrated to inactivate pathogens to levels consistent with the Class A criteria. This study was designed to evaluate pathogen inactivation by thermophilic anaerobic digestion in a mixed, continuous-flow reactor followed by batch or plug-flow treatment. In this first of a two-part series, we describe the performance of a continuous-flow laboratory reactor with respect to physical and chemical operating parameters; microbial inactivation in the combined continuous-flow and batch treatment system is described in the second part. Sludges from three different sources were treated at 53 degrees C, while sludge from one of the sources was also treated at 55 and 51 degrees C. Relatively short hydraulic retention times (four to six days) were used to represent a conservative operating condition with respect to pathogen inactivation. Treatment of a fermented primary sludge led to an average volatile-solids (VS) destruction efficiency of 45%, while VS destruction for the other two sources was near or below 38%, the Class A criterion for vector attraction reduction. Consistent with other studies on thermophilic anaerobic digestion of sludges at short residence times, effluent concentrations of volatile fatty acids (VFAs) were relatively high. Also consistent with other studies, the most abundant VFA in the effluent was propionate. Gas production ranged from 0.3 to 0.5 m3/kg VS fed and from 0.8 to 1.3 m3/kg VS destroyed.     

Droplet charging for wet scrubbers

Water droplet charge/mass of wet scrubbers was measured over the direct charging applied potential range of 0-20 kV, 30-70 pounds per square inch gauge (206.8-482.6 kPa) water pressure, and with spiral, impingement, and whirl nozzles. The measured charge/mass ranged from -0.0005 to 0.2 microcoulomb/gm and was directly related to the applied voltage. The water charge/mass was a function of the spray nozzle, with the smaller orifice lower-flow nozzles having the higher charge/mass.     

A qualitative sampling method for monitoring water quality in temporary channels or point sources and its application to pesticide contamination

A water-sampling device to monitor the quality of water periodically and temporarily flowing out of concrete tubes, sewers or channels is described. It inexpensively and easily enables a qualitative characterization of contamination via these point-source entry routes. The water sampler can be reverse engineered with different sizes and materials, once installed needs no maintenance, passively samples the first surge, and the emptying procedure is short. In an agricultural catchment area in Germany we monitored an emergency overflow of a sewage sewer, an outlet of a rainwater sewer and two small drainage channels as input sources to a small stream. Seven inflow events were analysed for 20 pesticide agents (insecticides, fungicides and herbicides). All three entry routes were remarkably contaminated. We found parathion-ethyl concentrations of 0.3 microg l(-1), diuron up to 17.3 microg l(-1), ethofumesate up to 51.1 microg l(-1), metamitron up to 92 microg l(-1) and prosulfocarb up to 130 microg l(-1).     

Partitioning of polychlorinated biphenyls and hexachlorobenzene into human faeces

The dietary absorption of persistent lipophilic organic pollutants (PLOPs) in humans is believed to occur via partitioning of the chemical between the lumen and the wall of the digestive tract. As such, the partitioning properties of the lumen contents are a key factor governing absorption. In this study, the partitioning properties of faeces were measured for 11 polychlorinated biphenyls and hexachlorobenzene (HCB). Four volunteers participated in the study, each of them providing faeces from a normal diet and a vegetarian diet. The faeces/gas equilibrium partition coefficient K(FG) varied by over three orders of magnitude between the different compounds. A linear relationship between log K(FG) and log KOA, the octanol/air partition coefficient, was observed. The slope of the relationship was > 1, indicating that the solvent properties of faeces were less polar than those of octanol. For a given compound, KFG varied up to a factor of 2.8 between the individuals on a normal diet. The influence of the vegetarian diet on K(FG) was negligible for the two volunteers who simply deleted fish and animal products from their normal diet, but K(FG) increased on average by a factor of 2 in the two individuals who increased their consumption of less readily digestible whole grains and vegetables in their vegetarian diet. On the basis of K(FG), the fugacities in the faeces were calculated. They were found to be much lower than the fugacities in blood. It is hypothesised that this is due to a temporary decrease in the fugacity in the wall of the jejunum caused by absorption of dietary lipids that results in equilibration between the lumen contents and the wall of the digestive tract at a fugacity below that present in the blood and the rest of the body.     

Investigation of unrecognized former secondary lead smelting sites: confirmation by historical sources and elemental ratios in soil

Twelve suspected former secondary lead smelting sites were investigated. Ten of the sites were confirmed to be former secondary lead smelters or lead works by historical fire insurance maps and contemporaneous metal industry trade directories. At eight sites sampled, the ratio Sb:Pb was closer to ratios from 10 known lead smelting sites than were the As:Pb and Cd:Pb ratios. Data from the 10 known lead smelting sites showed that the Sb:Pb ratio is most characteristic of secondary lead smelting sites. This is because the primary alloy smelted at such sites is antimonial lead. Lead contamination at the eight sites investigated here can be attributed At least in part to the former smelters because of the association between Sb and Pb.