Air Pollution in Singapore: Its Multielemental Aspect as Measured by Nuclear Analytical Techniques

Aerosol samples were collected in 1994 in Singapore on two occasions: once in June during the normal meteorological conditions and later in October during a long haze period caused by the heavy forest fire in Indonesia. Filtration and impaction collection methods were used simultaneously so that detailed elemental analysis of bulk as well as of different size fractions could be performed. Accelerator based nuclear analytical techniques such as Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and Nuclear Microscopy (NM) were used for analysis. These techniques are fast, truly multielemental and perfectly suited for routine analysis of a large number of aerosol samples. Typically all samples were analysed for the following 24 elements: Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Mn, Cr, Fe, Co, Ni, Cu, Zn, Ga, As, Br, Rb, Sr and Pb. Detection limits for bulk analysis were generally below ng/m3 and for single particle analysis absolute detectable mass was approximately 10-17 g. Additionally, trace elements such as Cd, Sn, Sb and Ba whose characteristic X-ray lines were normally "obscured" by the lines of other more abundant elements, were detected when analysing by nuclear microscope in single particle mode.Judging by the average concentrations of lead and sulphur which are good indicators of industrial component of air pollution the situation in Singapore is satisfactory. Pb was typically found in concentrations of 5 to 50 ng/m3 and sulphur in concentrations of 1 to 2 µg/m3. These concentrations are well below limits set by the World Health Organisation (1500 ng/m3 and 40 µg/m3, respectively). On the other hand during the haze period the average concentrations of elements like S, K, Ti, V, Mn, Ni, As and Pb were found to be 3 to 6 times higher than usual. Results are presented and discussed.     

Development of monitoring technology for airborne particulate matter

Particulate matter suspended in the air has adverse effects onhuman health. Its level of concentration is an important parameter in evaluating the degree of hazard it poses to the atmosphere. Conventional methods used in measuring particulatematter are often filter-based, which indicates some disadvantagesbecause such a base requires labor and time. In this study, to achieve real-time measurements, a new electrical method was developed for measuring PM10 and PM2.5 concentrations. The basicprinciple is to electrically charge particles passing through thePM inlet using a corona charger and measure the currents createdby charged particles to obtain the number concentration of particulate matter. A new type inlet based on the particle cupimpactor configuration was designed and its performance was evaluated. A unipolar diffusion charger was developed and thecharger's efficiency was determined experimentally in terms ofPn, which represents the penetration through the charger,P, times the average charge number acquired by a particle,n, for different particle sizes. The correlation was constructed between the PM10 (or the PM2.5) mass concentrationsand the electrical currents due to particles, which were chargedby the diffusion charger.     

Recycling of petroleum-contaminated sand

The environmental impact of using petroleum-contaminated sand (PCS) as a substitute in asphalt paving mixtures was examined. An appreciable component of PCS is oily sludge, which is found as the dregs in oil storage tanks and is also produced as a result of oil spills on clean sand. The current method for the disposal of oily sludge is land farming. However, this method has not been successful as an oil content of < 1% w/w is required, and difficulty was encountered in reaching this target. The reuse of the sludge in asphalt paving mixtures was therefore considered as an alternative. Standard tests and environmental studies were conducted to establish the integrity of the materials containing the recycled sludge. These included physical and chemical characterization of the sludge itself, and an assessment of the mechanical properties of materials containing 0%, 5%, 22% and 50% oily sludge. The blended mixtures were subjected to special tests, such as Marshall testing and the determination of stability and flow properties. The experimental results indicated that mixtures containing up to 22% oily sludge could meet the necessary criteria for a specific asphalt concrete wearing course or bituminous base course. To maximize the assay from the recycled material, the environmental assessment was restricted to the 50% oily sludge mixture. Leachates associated with this particular mixture were assayed for total organic residue and certain hazardous metal contaminants. The results revealed that the organics were negligible, and the concentrations of the metals were not significant. Thus, no adverse environmental impact should be anticipated from the use of the recycled product. Our research showed that the disposal of oily sludge in asphalt paving mixtures could possibly yield considerable savings per tonne of asphalt concrete, and concurrently minimize any direct impact on the environment.     

Concentration and Distribution of Persistent Organic Pollutants (POPs) in Harbour Dredging Sediments: A Pilot Study Using a Statistical Approach for a More Efficient Characterisation and Management

The Italian guidelines concerning the dumping of dredgingmaterials implies chemical, physical and microbiologicalcharacterisation of dumping sediments collected through aspecific sampling strategy.POP's such as PCB's and organochlorine pesticides, areconsidered as priority pollutants in all the InternationalConventions for the protection of the marine environment, inconsequence of their persistence, toxicity and bioaccumulation capacity.In the present article the concentrations and distribution ofPCB's and organochlorine pesticides in dredging sediments ofPiombino harbour (northern Thyrrenian sea) were investigates.The results showed high POP's concentrations in all the studiedareas. The maximum values were: 3.94 mg kg^-1 dry weight for PCB's(IUPAC Nos. 28; 52; 101, 118; 137; 153; 180; 209); 2.04 mg kg^-1 d.w.for HCH's (-, -, - and -hexachlorocyclohexane isomers); 0.28 mg kg^-1 d.w. for DD's (DDT + DDE + DDD).Subsequently, the data related to each pollutant were treatedwith statistical tests, in order to verify how well the samplingstrategy is able to represent the distribution of contaminantsin the dredging area. Finally, management strategies werederived for the studied dredging sediments.     

Chlorinated Hydrocarbons in Livers of American Mink (Mustela vison) and River Otter (Lutra canadensis) from the Columbia and Fraser River Basins, 1990–1992

We investigated chlorinated hydrocarbon contaminants in aquatic mustelid species on the Fraser and Columbia Rivers of northwestern North America. Carcasses of river otter (Lutra canadensis) (N=24) and mink (Mustela vison) (N=34) were obtained from commercial trappers during the winters of 1990–91 and 1991–92. Pooled liver samples were analyzed for organochlorine pesticides, polychlorinated biphenyls (PCBs), including non-ortho congeners, polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). Most samples contained detectable concentrations of DDE, PCBs, although there was substantial variability in patterns and trends among neighboring samples. Concentrations of DDE were in some mink and several otter samples from the lower Columbia River elevated (to 4700 g/kg wet weight); excluding one mink sample from the Wenatchee area, mean DDE levels generally decreased between 1978–79 and 1990–92. PCBs were present in all samples. PCB concentrations in otter livers collected from the lower Columbia were ten-fold lower than measured a decade previously; nevertheless, a sample taken near Portland had a mean concentration of 1500 g/kg, within a range of concentrations associated with reproductive effects in captive mink. Concentrations of 2,3,7,8-TCDD and TCDF were generally below detection limits, except for one otter collected near a pulp mill at Castlegar, on the upper Columbia, with 11 ng TCDD/kg in liver. Elevated concentrations of higher chlorinated PCDD/Fs, probably resulting from use of chlorophenolic wood preservatives, were found in both species; one otter sample from the lower Columbia had 2200 ng OCDD/kg. International TCDD toxic equivalent levels in mink (31 ng/kg) and otter (93 ng/kg) from the lower Columbia River approached toxicity thresholds for effects on reproduction in ranch mink.     

State estimation in wastewater engineering: Application to an anaerobic process

The use of an extended Kalman filter for state estimation in biological wastewater treatment processes is discussed. The application of the technique requires an adequate mechanistic dynamic model and the identification and modelling of the major sources of stochastic disturbances in the process. The filter allows the on-line tracking of process variables which are not directly measurable. The use of an extended Kalman filter is illustrated through a simulated application to a high rate anaerobic wastewater treatment process.     

Soil sampling and analysis for volatile organic compounds

Concerns over data quality have raised many questions related to sampling soils for volatile organic compounds (VOCs). This paper was prepared in response to some of these questions and concerns expressed by Remedial Project Managers (RPMs) and On-Scene Coordinators (OSCs). The following questions are frequently asked:

1. Is there a specific device suggested for sampling soils for VOCs?
2. Are there significant losses of VOCs when transferring a soil sample from a sampling device (e.g., split spoon) into the sample container?
3. What is the best method for getting the sample from the split spoon (or other device) into the sample container?
4. Are there smaller devices such as subcore samplers available for collecting aliquots from the larger core and efficiently transferring the sample into the sample container?
5. Are certain containers better than others for shipping and storing soil samples for VOC analysis?
6. Are there any reliable preservation procedures for reducing VOC losses from soil samples and for extending holding times?

Guidance is provided for selecting the most effective sampling device for collecting samples from soil matrices. The techniques for sample collection, sample handling, containerizing, shipment, and storage described in this paper reduce VOC losses and generally provide more representative samples for volatile organic analyses (VOA) than techniques in current use. For a discussion on the proper use of sampling equipment the reader should refer to other sources (Acker, 1974; U.S. EPA, 1983; U.S. EPA, 1986a). Soil, as referred to in this report, encompasses the mass (surface and subsurface) of unconsolidated mantle of weathered rock and loose material lying above solid rock. Further, a distinction must be made as to what fraction of the unconsolidated material is soil and what fraction is not. The soil component here is defined as all mineral and naturally occurring organic material that is 2 mm or less in size. This is the size normally used to differentiate between soils (consisting of sands, silts, and clays) and gravels. Although numerous sampling situations may be encountered, this paper focuses on three broad categories of sites that might be sampled for VOCs:

1. Open test pit or trench.
2. Surface soils (<5 ft in depth).
3. Subsurface soils (>5 ft in depth).

     

Analysis of pollutant levels in central Hong Kong applying neural network method with particle swarm optimization

Air pollution has emerged as an imminent issue in modernsociety. Prediction of pollutant levels is an importantresearch topic in atmospheric environment today. For fulfillingsuch prediction, the use of neural network (NN), and inparticular the multi-layer perceptrons, has presented to be acost-effective technique superior to traditional statisticalmethods. But their training, usually with back-propagation (BP)algorithm or other gradient algorithms, is often with certaindrawbacks, such as: 1) very slow convergence, and 2) easilygetting stuck in a local minimum. In this paper, a newlydeveloped method, particle swarm optimization (PSO) model, isadopted to train perceptrons, to predict pollutant levels, andas a result, a PSO-based neural network approach is presented. The approach is demonstrated to be feasible and effective bypredicting some real air-quality problems.     

Application of cryofocusing hydride generation and atomic fluorescence detection for dissolved mercury species determination in natural water samples

The concentration levels of mercury (Hg) species in natural water samples are usually low. Consequently, accurate analysis with low detection limits is still a major problem. In this work, a method was applied for the simultaneous direct determination of dissolved mercury species in water samples by on-line hydride generation (HG), cryogenic trapping (CT), gas chromatography (GC) and detection by atomic fluorescence spectrometry (AFS). The suitability of the method for real samples with different organic matter and chloride contents was evaluated by recovery experiments in synthetic and natural spiked water samples. The HG method was compared with other current available methods for mercury analysis with respect to the different fraction of mercury analysed, i.e. 'reactive', 'reducible' or total. HG derivatization and SnCl2 reduction (with and without previous oxidation with BrCl) were applied to synthetic and natural (spiked and non-spiked) water samples. The influence of chloride and dissolved organic matter concentrations was studied. The results suggest that the HG procedure is suitable for the simultaneous determination of Hg2+ and MeHg+ in surface water samples. Inorganic mercury analysed by HG (i.e. reducible) is close to the total inorganic mercury.     

The efficacy of protoporphyrin as a predictive biomarker for lead exposure in canvasback ducks: Effect of sample storage time

We used 363 blood samples collected from wild canvasback dueks (Aythya valisineria) at Catahoula Lake, Louisiana, U.S.A. to evaluate the effect of sample storage time on the efficacy of erythrocytic protoporphyrin as an indicator of lead exposure. The protoporphyrin concentration of each sample was determined by hematofluorometry within 5 min of blood collection and after refrigeration at 4 °C for 24 and 48 h. All samples were analyzed for lead by atomic absorption spectrophotometry. Based on a blood lead concentration of 0.2 ppm wet weight as positive evidence for lead exposure, the protoporphyrin technique resulted in overall error rates of 29%, 20%, and 19% and false negative error rates of 47%, 29% and 25% when hematofluorometric determinations were made on blood at 5 min, 24 h, and 48 h, respectively. False positive error rates were less than 10% for all three measurement times. The accuracy of the 24-h erythrocytic protoporphyrin classification of blood samples as positive or negative for lead exposure was significantly greater than the 5-min classification, but no improvement in accuracy was gained when samples were tested at 48 h. The false negative errors were probably due, at least in part, to the lag time between lead exposure and the increase of blood protoporphyrin concentrations. False negatives resulted in an underestimation of the true number of canvasbacks exposed to lead, indicating that hematofluorometry provides a conservative estimate of lead exposure.The U.S. Government's right to retain a non-exclusive, royalty-free licence in and to any copyright is acknowledgedDeceased