SAFEST TO TRAVEL BY BICYCLE,CAR, OR BIG TRUCK?

This study compares highway crash incidence, injuries, and costs by vehicle type. Annual crash and injury incidence were estimated using Crashworthiness Data System (1988-1991), National Automotive Sampling System (1982-1986), General Estimates System (1992-1993), and Fatal Analysis Reporting System (1993) data. Costs were computed based on restraint use, body region, and threat-to-life severity of the injury. Costs were then allocated between vehicle types using three different methods in order to answer comparative safety questions. Motor vehicle and bicycle crash costs total $389 billion annually; 75% resulting from passenger vehicles. Motorcycles and bicycles have the highest costs per 1000 vehicle and passenger miles; costs per victim are highest for pedestrians, bicyclists, and motorcyclists. Costs per vehicle mile for heavy trucks and passenger cars are comparable but exceed costs for light trucks. Passenger vehicle occupants are safest if a crash occurs. Light truck, other single truck, and bus occupants have the lowest cost per passenger mile, but higher costs than air and rail travelers. Motorcyclists face the greatest risks. Combination trucks may not impose an excess risk to other drivers, but their drivers face large risks.     

Biomechanics of Brain and Spinal-Cord Injury: Analysis of Neuropathologic and Neurophysiology Experiments

This study analyzes 46 brain and 48 spinal-cord impact experiments. The velocity of brain impact was 2.0-10.0 m/s and displacement, 0.75-5.0 mm (5.3-33% compression) using a controlled pneumatic impact. The velocity of spinal-cord impact was 1.5-6.0 m/s and displacement, 1.25-3.25 mm (25-65% compression). Brain injury varied from cortical contusion, diffuse axonal injury (DAI), to fatalities, and spinal-cord injury from temporary to complete loss of somatosensory-evoked potentials. Logist functions were determined for each injury severity and various biomechanical parameters, VC, C, V, and combinations. Brain and spinal-cord injury is most strongly correlated to VC, the viscous response. The goodness-of-fit was x² = 22.1, R-0.84 and p< 0.0000 for fatal brain injury, x² = 27.5, R = 0.96 and p< 0.0000 for cortical contusion, and x² = 17.7, R = 0.49 and p < 0.0001 for partial recovery of spinal-cord conduction. Neural tissue is viscoelastic, with a rate-dependent tolerance related to energy absorption. VC is a measure of energy absorption by impact deformation and is predictive of neural contusion, DAI, long-duration coma, spinal-cord dysfunction, and death. Tolerances for various severities of neural injury are presented. At the tissue level, VC is the product of strain and strain-rate, ε dε/dt. The research shows that strain is not a sufficient parameter of neural injury risk, and that the product of strain and strain-rate is a key biomechanical parameter for brain and spinal-cord injury.     

Review: The Dynamics of Near Vertex Head Impact and its Role in Injury Prevention and the Complex Clinical Presentation of Basicranial and Cervical Spine Injury

The clinical presentation of cervical and basilar skull fractures following bead impact is often complex, particularly when multiple noncontiguous fractures are present. Based on the results of 22 human cadaver head-neck impact experiments, a biomechanical framework of spinal injury is developed in which these complex cases may be better understood. This includes the significance of head rebound, head and neck decoupling, cervical spine buckling, cervical injury mechanisms, basilar skull fractures, and cervical spine tolerance. These data also demonstrate that compliant pads significantly increase the risk for spinal injury though they also significantly reduce peak head force and the head injury criteria (p < 0.04). On the basis of these observations, we hypothesize that impact injury should be modeled as the dynamic response of two large masses, coupled by a segmented curved beam-column composed of seven small masses with interposed nonlinear viscoelastic flexibility elements.     

Protection Against Dust by Respirators

This article is a brief review of the mechanism of action of fibrous filters and of the performance of respirators; it neglects many of the complications discussed in longer and more detailed articles. An expression is given for the pressure drop across a filter in terms of fibre diameter and filtration velocity. The particle capture mechanisms of interception and diffusional deposition are introduced and the way in which filtration efficiency varies with particle size is discussed. Filters with fibres of small diameter are shown to be the most efficient, but their use can cause problems. Electrically charged materials are widely used in respirators because of their high efficiency and low pressure drop. Types of material, their means of charging, and their method of action are described. An account is given of respirator leakage, the protection factor, and of the way that these may vary in a period of use. The leakage of air and particles through face seal leaks and leaky valves is discussed. The frequent discrepancy in the protection given by respirators in the workplace, on the one hand, and that suggested by laboratory measurements, on the other, is reviewed, and the article ends with an account of the combined effect of aerosol penetration through a filter and through a leak.     

Defending the Wrist Deviation Test for Carpal Tunnel Syndrome Screening: A Comparison of Vibration Thresholds and Distal Motor Latency

This research used distal motor latency (DML) and vibration thresholds (VT) to evaluate 84 hand activity and wrist deviation combinations to determine the best association with carpal tunnel syndrome (CTS). Female volunteers, 2 healthy and 2 CTS diagnosed, were age matched and operated a keyboard for 4 hrs a day. Room temperature was 28°C(±2). Beginning DML and VT were taken with a relaxed neutral posture hand. The wrist was deviated in a randomly selected combination, and determinations were taken at 5-min intervals. The trial ended at 20 min or when discomfort was felt. The CTS conditions were discriminated by pain four times, DML once, and VT 14 times. Vibrometry was the most consistent CTS discriminator. The best VT results for wrist positions were obtained with wrist extension and extended extension, whereas the unclenched, clenched, and loaded power grip activities proved to be the most consistent hand activities.     

A System for Measuring Vertical Concentration Profiles of Gaseous Pollutants,Using Carbon Dioxide as a Case Study

An electronically-controlled sampling system, characterised by its organ pipe design, has been developed for sampling air sequentially, at different heights within the breathing zone. Data are automatically logged at the different receptor levels, for the determination of the average vertical concentration profile of gaseous pollutants. The system has been coupled to a carbon dioxide monitor and used in a brief study of the spatial and temporal variation of indoor carbon dioxide concentration. The system can easily be extended for different heights or modified for use with other types of gas monitor. The results of a trial run, which was carried out in a coffee room, are presented and applications of the Organ Pipe Sequential Sampling (OPSS) system are discussed.     

Ergonomic Aspects of a Virtual Environment

A virtual environment is an interactive graphic system mediated through computer technology that allows a certain level of reality or a sense of presence to access virtual information. To create reality in a virtual environment, ergonomics issues are explored in this paper, aiming to develop the design of presentation formats with related information, that is possible to attain and to maintain user-friendly application.     

Ergonomics and Quality Management—Humans in Interaction With Technology,Work Environment,and Organization

Abstract

In many studies, ergonomics has been shown to influence human performance. The aim of this paper was to demonstrate imp ortan t ergonomics influences on quality in industrial production, from the perspective of interactions between humans, technology, organization, and work environment. A second aim was to elab orate on the implications of these findings for the development of quality management strategies. This paper shows that ergonomics problems in terms of adverse work environmental conditions, in appropriate design of technology, and an unsuitable org an izatio n are important causes of quality deficiencies. Problem solving aimed at improving ergonomics, quality, and productivity simultaneously is likely to obtain sup po rt from most of the interest parties of the company, and may also enhance participation. Ergonomics has the potential of becoming a driving force for the development of new quality management strategies.