An antibiotic composite electrode for improving the sensitivity of electrochemically active biofilm biosensor

• Antibiotic azithromycin employed in graphite electrode for EAB biosensor. • Azithromycin at 0.5% dosage increased the sensitivity for toxic formaldehyde. • Azithromycin increased the relative abundance of Geobacter. • Azithromycin regulated thickness of electroactive biofilm. Extensive research has been carried out for improved sensitivity of electroactive biofilm-based sensor (EAB-sensor), which is recognized as a useful tool in water quality early-warning. Antibiotic that is employed widely to treat infection has been proved feasible in this study to regulate the EAB and to increase the EAB-biosensor’s sensitivity. A novel composite electrode was prepared using azithromycin (AZM) and graphite powder (GP), namely AZM@GP electrode, and was employed as the anode in EAB-biosensor. Different dosages of AZM, i.e., 2 mg, 4 mg, and 8 mg, referred to as 0.25%, 0.5% and 1% AZM@GP were under examination. Results showed that EAB-biosensor was greatly benefited from appropriate dosage of AZM (0.5% AZM@GP) with reduced start-up time period, comparatively higher voltage output, more readable electrical signal and increased inhibition rate (30%-65% higher than control sensor with GP electrode) when exposing to toxic formaldehyde. This may be attributed to the fact that AZM inhibited the growth of non-EAM without much influence on the physiologic or metabolism activities of EAM under proper dosage. Further investigation of the biofilm morphology and microbial community analysis suggested that the biofilm formation was optimized with reduced thickness and enriched Geobacter with 0.5% AZM@GP dosage. This novel electrode is easily fabricated and equipped, and therefore would be a promising way to facilitate the practical application of EAB-sensors.     

Spatiotemporal variations of dissolved organic matter in a typical multi-source watershed in northern China: a fluorescent evidence

Environmental Science and Pollution Research - The amount of dissolved organic matter (DOM) in a multi-source watershed is important for complete management and assessing the river basin’s...     

A review of antibiotic removal from domestic wastewater using the activated sludge process: removal routes,kinetics and operational parameters

Environmental Science and Pollution Research - Many advanced technologies have shown encouraging results in removing antibiotics from domestic wastewater. However, as activated sludge treatment is...     

Human health risk assessment of heavy metals from PM2.5 in China’s 29 provincial capital cities

Environmental Science and Pollution Research - After years of governance, China’s PM2.5 pollution has improved significantly, but some problems remain. PM2.5 is the carrier of many heavy...     

Constructing 3D magnetic flower-like Fe3O4@SiO2@Co3O4@BiOCl heterojunction photocatalyst for degrading rhodamine B

Environmental Science and Pollution Research - In this work, the 3D magnetic flower-like Fe3O4@SiO2@Co3O4@BiOCl heterojunction photocatalyst was successfully prepared. The combination of BiOCl with...     

基于HFACS-BN模型的危险化学品事故人因路径分析*

为提高危险化学品安全管理水平,收集我国134起以人为主因的危险化学品事故,构建危险化学品事故的HFACS-BN模型,并基于贝叶斯网络对危险化学品事故中的人因路径及各因素灵敏度进行分析。研究结果表明:行为违规是导致事故的最主要不安全行为;在复杂路径中,环境因素和操作者状态具有较高的灵敏度,与其相关的风险认知与处理不当是阻碍事故预防的关键因素;在非复杂路径中,操作者状态与运行计划不当具有较高的灵敏度,其所涉及的监督违规、组织过程和组织氛围,是导致危险化学品事故的根本起点,并可依此分析事故直接原因和间接原因;操作者状态在2种路径中均表现出高灵敏度,因此化工企业在人员管理上要加强关注职工状态,减少不安全行为的出现。     

基于改进社会力模型的地铁大客流疏散能力研究*

为有效应对大客流情景下人群拥挤对地铁站正常运行带来的影响,采用社会力模型和Anylogic仿真软件,对地铁站大客流疏散能力进行建模和分析,从客观、主观、管理视角分析影响客流疏散能力的因素,基于改进社会力模型刻画行人行为,分析影响地铁车站疏散能力的3个关键因素,并以南宁地铁1号线朝阳广场站为背景进行研究。研究结果表明:行人密度是影响地铁站疏散能力的关键因素,出入口选择策略和行人亲属关系比例对疏散能力影响显著,研究结果可为地铁客流疏散提出针对性建议。     

电法填埋场渗漏检测供电电极接地电阻研究

采用电法进行垃圾填埋场渗漏检测时,供电电极的接地电阻对回路电流起决定性作用.分别推导了半球状供电电极和圆柱状供电电极的接地电阻表达式,并对影响接地电阻大小的主要因素进行了分析和试验验证.结果表明:①电极的接地电阻主要由电极附近的土壤电阻决定;②随着电极埋深的增加,电极的接地电阻减少,但当埋深超过40 cm时,随着电极埋深的增加,电极接地电阻的减小趋势变缓;③随着电极直径的增加,电极的接地电阻减少.实际应用中,电极的埋深和直径应尽可能大一些,但电极直径较大时,电极质量也会显著增加,给操作带来不便.因此,可将电极直径定为10～15 cm.此外,由于土壤一般为颗粒状,这使得土壤和电极不能完全接触,为降低接地电阻,可对电极附近的土壤进行浇水.