Vehicle-Induced Lead and Cadmium Contamination of Roadside Soil and Plants in Italy

Lead and cadmium concentrations in spontaneous vegetation and in soil sampled at various distances (0–208 m) from several motorways throughout Italy were measured. Lead and cadmium concentrations appear to be correlated to distance from the motorway and to traffic levels. A comparison with data from a remote and unpolluted site shows that foliar lead concentrations can be up to 40 times higher, and foliar cadmium concentrations up to 3 times higher. Plants behave differently in their accumulation of lead and cadmium; conifers present the highest levels. Also the various receptors and compartments of the roadside ecosystem differ in their accumulation of lead and cadmium; soil and bark have consistently higher concentrations, while the leaves and twigs of trees have consistently lower levels. the data recorded by ad hoc introduced bio-accumulating plants (Lolium multiflorum L.) are consistent with those of the spontaneous vegetation. the concentrations of both lead and cadmium in Lolium vary from June to November, following in part the fluctuation in traffic density.     

Facile characterization of polymer fractions from waste electrical and electronic equipment (WEEE) for mechanical recycling

In view of the environmental problem involved in the management of WEEE, and then in the recycling of post-consumer plastic of WEEE there is a pressing need for rapid measurement technologies for simple identification of the various commercial plastic materials and of the several contaminants, to improve the recycling of such wastes.This research is focused on the characterization and recycling of two types of plastics, namely plastic from personal computer (grey plastic) and plastic from television (black plastic). Various analytical techniques were used to monitor the compositions of WEEE. Initially, the chemical structure of each plastic material was identified by Fourier transform infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC). Polymeric contaminants of these plastics, in particular brominated flame retardants (BFRs) were detected in grey plastics only using different techniques. These techniques are useful for a rapid, correct and economics identification of a large volumes of WEEE plastics.     

Heavy metals removal and hydraulic performance in zero-valent iron/pumice permeable reactive barriers

Long-term behaviour is a major issue related to the use of zero-valent iron (ZVI) in permeable reactive barriers for groundwater remediation; in fact, in several published cases the hydraulic conductivity and removal efficiency were progressively reduced during operation, potentially compromising the functionality of the barrier. To solve this problem, the use of granular mixtures of ZVI and natural pumice has recently been proposed. This paper reports the results of column tests using aqueous nickel and copper solutions of various concentrations. Three configurations of reactive material (ZVI only, granular mixture of ZVI and pumice, and pumice and ZVI in series) are discussed. The results clearly demonstrate that iron-pumice granular mixtures perform well both in terms of contaminant removal and in maintaining the long-term hydraulic conductivity. Comparison with previous reports concerning copper removal by ZVI/sand mixtures reveals higher performance in the case of ZVI/pumice.     

Effluents from MBT plants: Plasma techniques for the treatment of VOCs

Mechanical–biological treatments (MBTs) of urban waste are growing in popularity in many European countries. Recent studies pointed out that their contribution in terms of volatile organic compounds (VOCs) and other air pollutants is not negligible. Compared to classical removal technologies, non-thermal plasmas (NTP) showed better performances and low energy consumption when applied to treat lowly concentrated streams. Therefore, to study the feasibility of the application of NTP to MBTs, a Dielectric Barrier Discharge reactor was applied to treat a mixture of air and methyl ethyl ketone (MEK), to simulate emissions from MBTs. The removal efficiency of MEK was linearly dependent upon time, power and specific input energy. Only 2–4% of MEK was converted to carbon dioxide (CO₂), the remaining carbon being involved in the formation of byproducts (methyl nitrate and 2,3-butanedione, especially). For future development of pilot-scale reactors, acting on residence time, power, convective flow and catalysts will help finding a compromise between energy consumption, desired abatement and selectivity to CO₂.     

Using Fallout Lead-210 Measurements to Estimate Soil Erosion in Three Small Catchments in Southern Italy

Soil erosion and associated off-site environmental impacts have attracted increasing attention in recent decades, and there is a growing need for reliable information on rates of soil loss. The potential for using ¹³⁷Cs fallout to quantify rates and patterns of soil redistribution over medium-term timescales (ca. 45 years) has been successfully demonstrated in a wide range of environments around the world. The similar behaviour of fallout ²¹⁰Pb in soils offers potential for its use as an alternative to ¹³⁷Cs, in areas where ¹³⁷Cs inventories are low or are complicated by additional fallout from the Chernobyl accident. There have, however, to date been few attempts to validate the use of fallout ²¹⁰Pb measurements for assessing erosion rates. This paper reports an attempt to explore the use of fallout ²¹⁰Pb to estimate rates of water-induced soil erosion on uncultivated land. It focuses on three small forest/rangeland catchments located in Calabria, southern Italy, for which measurements of sediment output are available. Comparison of the estimates of net soil loss from the catchments derived from ²¹⁰Pb measurements with the measured sediment output, confirmed the validity of the ²¹⁰Pb approach. The soil redistribution rates estimated using ²¹⁰Pb measurements were also consistent with equivalent estimates obtained for the same study catchments using ¹³⁷Cs measurements.     

Atmospheric fall-out of metals around the Murano glass-making district (Venice,Italy)

Background, aim and scope  

Murano’s glass-makers have held a monopoly on quality glass-making for centuries known all over the world. Artistic glass manufacture entails exposure to complex mixtures of pollutants, including metals. A few studies have reported high levels of trace elements in marine waters, sediments and mussels around Murano and shown that emissions from Murano glass-making workshops significantly influence air quality in the Venice area. Nevertheless, to date, there is very little information on atmospheric concentrations and virtually none on atmospheric deposition fluxes of trace elements around the island. This study presents data on the distribution of trace elements in the air and atmospheric depositions around Murano, based on a 2-year sampling period.     

Monitoring of abandoned quarries by remote sensing and in situ surveying

In Italy quarrying causes relevant environmental damages and alterations to the land and the ecosystems. Despite the present Italian legislation requiring the restoration of the sites after exploitation, most of the quarries, both the abandoned and the still operational ones, are not restored.The objective of this work is to indicate a monitoring methodology in order to survey the present state of the quarry sites and their evolution in time, which are the basic data needed to implement an adequate land reclamation project.Such methodology has been applied to several abandoned limestone quarries in the Latina province (close to Rome), characterised by a typical Mediterranean vegetation, but it can be applied to any other kind of litology and vegetation.The land monitoring has been realised both by using remote sensing techniques, supported by a Geographic Information System of the studied area, and by in situ surveying. The in situ surveying was able to assess the capability of the remote sensing model to describe the state of each site.