Depth-dependence and monthly variability of charophyte biomass production: consequences for the precipitation of calcium carbonate in a shallow <Emphasis Type="Italic">Chara</Emphasis>-lake

The month-to-month variability of biomass and CaCO₃ precipitation by dense charophyte beds was studied in a shallow Chara-lake at two depths, 1 and 3 m. Charophyte dry weights (d.w.), the percentage contribution of calcium carbonate to the dry weight and the precipitation of CaCO₃ per 1 m² were analysed from May to October 2011. Physical-chemical parameters of water were also measured for the same sample locations. The mean dry weight and calcium carbonate precipitation were significantly higher at 1 m than at 3 m. The highest measured charophyte dry weight (exceeding 2000 g m^?2) was noted at 1 m depth in September, and the highest CaCO₃ content in the d.w. (exceeding 80 % of d.w.) was observed at 3 m depth in August. The highest CaCO₃ precipitation per 1 m² exceeded 1695 g at 1 m depth in August. Significant differences in photosynthetically active radiation (PAR) were found between 1 and 3 m depths; there were no significant differences between depths for other water properties. At both sampling depths, there were distinct correlations between the d.w., CaCO₃ content and precipitation and water properties. In addition to PAR, the water temperature and magnesium and calcium ion concentrations were among the most significant determinants of CaCO₃ content and d.w. The results show that light availability seems to be the major factor in determining charophyte biomass in a typical, undisturbed Chara-lake. The study results are discussed in light of the role of charophyte vegetation in whole ecosystem functioning, with a particular focus on sedimentary processes and the biogeochemical cycle within the littoral zone.     

Desorption of PCDD/PCDF from municipal solid waste incinerator flyash under post-combustion plant conditions

The influence of temperature on the levels of PCDD and PCDF remaining in, and desorbed from, a municipal solid waste incinerator flyash was investigated by heating the ash to between 200 and 400 degrees C under a simulated flue gas for four days reaction time. Considerable desorption of PCDD/PCDF from the flyash was seen at 275 degrees C and above. Maximum desorption occurred at 350 degrees C, with the equivalent of nearly eight times the total PCDD/PCDF concentration of the original flyash being lost to the vapour phase per unit mass of initial flyash. The I-TEQ value of the desorbed PCDD/PCDF was considerable, being over fourteen times that of the original flyash at 325 degrees C. The results indicate that formation of PCDD/PCDF on flyash deposits in the post-combustion plant of incinerators can result in the release of significant amounts of PCDD/PCDF to the flue gas stream.     

Characterization of the toxic effects of cadmium and 3.5-dichlorophenol on nitrifying activity and mortality in biologically activated sludge systems—effect of low temperature

Background, aims, and scope  Sometimes, urban wastewaters convey a more or less significant part of toxic products from industries or the craft industry. Nitrifying activity can be affected by these substances, implying higher ammonia concentrations in the outlet effluent and contributing to toxicity for the aquatic environment. Moreover, the more stringently treated wastewater standards now require a reliable treatment for nitrogen. One of the key issues is the identification of the inhibition behavior of nitrifying bacteria facing a toxic substance. This new understanding could then finally be integrated into models in order to represent and to optimize wastewater treatment plants (WWTP) operation in cases involving ‘toxic scenarios’. Materials and methods  The toxic substances studied in this work, cadmium and 3.5-dichlorophenol (3.5-DCP), are representative of chemical substances commonly found in municipal sewage and industrial effluents and symbolize two different contaminant groups. The effects of Cd and 3.5-DCP on nitrification kinetics have been investigated using respirometry techniques. Results  IC50 values determination gives concentrations of 3.1 mg/L for 3.5-DCP and 45.8 mg/L for Cd at 21 ± 1°C. The variation to low temperature seems to have no real effect on IC50 for DCP, but induces a decrease of cadmium IC50 to 27.5 mg/L at 14°C. Finally, specific respirometric tests have been carried out in order to determine the potential effect of these toxic substances on the nitrifying decay rate b _a . No significant effect has been noticed for Cd, whereas the presence of 3.5-DCP (at IC50 concentration) induced a dramatic increase of b _a at 20°C. The same behavior has been confirmed by experiments performed in winter periods with a sludge temperature around 12°C. Discussion  The target substances have different modes of action on activity and mortality, notably due to the abilities of the contaminant to be precipitated, accumulated, or even to be progressively degraded. Studies realized at low temperature confirmed this assumption, and put in evidence the effect of temperature on toxic substances capable of being biosorbed. However, the change in the sludge sample characteristics can be pointed out as a problem in the investigation of the temperature effect on nitrification inhibition, as biosorption, bioaccumulation, and predation are directly linked to the sludge characteristics (VSS concentration, temperature) and the plant operating conditions (loading rates, sludge age, etc.). Conclusions  This work brings new understandings concerning the action mode of these specific contaminants on nitrifying bacteria and, in particular, on the role of temperature. The experiments lead to the determination of the IC50 values for both toxic substances on biological nitrification. The inhibition mechanisms of Cd and 3.5-DCP on nitrifying activity have been simply represented by a non-competitive inhibition model. Recommendations and perspectives  Other experiments carried out in a continuous lab-scale pilot plant should be done with a proper control of the operating conditions and of the sludge characteristics in order to better understand the mechanisms of nitrification inhibition for each contaminant. Finally, these first results show that toxic substances can have an effect on the growth rate but also on the decay rate, depending on the characteristics of the toxic substance and the sludge. This eventual double effect would imply different strategies of WWTP operation according to the behavior of the contaminant on the bacteria.     

The Fallacies of Concurrent Climate Policy Efforts

Climate policy has assumed an extreme degree of urgency in the international debate in recent years. This article begins by taking a critical look at the scientific underpinnings of the efforts to stabilize the climate. It points to several serious question marks on the purported relationship between greenhouse gas emissions and global warming, and expresses distrust about claims of impending catastrophes related to rising sea levels, hurricanes, and spread of infectious disease. It then reviews the concurrent climate policy efforts and concludes that they are incoherent, misguided and unduly costly, and that they have so far had no perceptible impact on anthropogenic greenhouse gas emissions. The exceedingly ambitious policy plans currently under preparation suffer from similar fallacies. For these reasons, but also because of the remaining scientific doubts and the exorbitant costs that have to be incurred, skepticism is expressed about the preparedness to implement the climate policy plans currently on the table.     

EPA’s LIMB Development and Demonstration Program

This paper describes and discusses key design features of the retrofit of EPA’s Limestone Injection Multistage Burner (LIMB) system to an operating, wall-fired utility boiler at Ohio Edison’s Edgewater Station, based on the preliminary engineering design. It further describes results of pertinent projects in EPA's LIMB program and shows how these results were used as the basis for the design of the system. The full-scale demonstration is expected to prove the effectiveness and cost of the LIMB concept for use on large-scale utility boilers. To date, a preliminary engineering design for the Edgewater unit has been prepared incorporating the technology developed in smaller-scale studies. The schedule calls for system start-up by March 1987. EPA is engaged in a multiyear program to develop an improved control technology for emission of sulfur and nitrogen oxides from the combustion of fossil fuels. The technology involves staged-flow coal burners and injection of a reactive sorbeht into the furnace to reduce emissions. The program includes fundamental studies of reaction chemistry and kinetics, bench and pilot scale experimental studies, a full-scale demonstration, and economic and applicability studies. It is structured to establish a basis for future public sector commercialization, as well as help in understanding the technology’s controlling factors.     

Effects of soil moisture depletion on vegetable crop uptake of pharmaceuticals and personal care products (PPCPs)

Agricultural crops have a long history of being irrigated with recycled wastewater (RW). However, its use on vegetable crops has been of concern due to the potential prevalence of microcontaminants, such as pharmaceuticals and personal care products (PPCPs) in the latter, which represents a possible health hazard to consumers. We investigated the uptake of three PPCPs (atenolol, diclofenac, and ofloxacin), at three different concentrations in irrigation water (0.5, 5, and 25 μg L^?1) in relation to three varying volumetric soil moisture depletion levels of 14 % (?4.26 kPa), 10 % (?8.66 kPa), and 7 % (?18.37 kPa) by various vegetable crop species. Experiments were conducted in a split-split block completely randomized design. PPCPs were extracted using a developed method of accelerated solvent extraction and solid phase extraction and analyzed via liquid chromatography mass spectrometry (LCMS). Results indicate that all treated crops were capable of PPCP uptake at nanogram per gram concentrations independent of the applied soil moisture depletion levels and PPCP concentrations. Ofloxacin was the chemical with the highest uptake amounts, followed by atenolol and then diclofenac. Although the results were not statistically significant, higher concentrations of PPCPs were detected in plants maintained under higher soil moisture levels of 14 % (?4.26 kPa).     

Biodegradability of algal-derived organic matter in a large artificial lake by using stable isotope tracers

In order to understand the biodegradability of algal-derived organic matter, biodegradation experiments were conducted with ¹³C and ¹⁵N-labeled natural phytoplankton and periphytic algal populations in experimental conditions for 60 days. Qualitative changes in the dissolved organic matter were also determined using parallel factor analysis and the stable carbon isotopic composition of the hydrophobic dissolved organic matter through the experimental period. Although algal-derived organic matter is considered to be easily biodegradable, the initial amounts of total organic carbon newly produced by phytoplankton and periphytic algae remained approximately 16 and 44 % after 60 days, respectively, and about 22 and 43 % of newly produced particulate nitrogen remained. Further, the dissolved organic carbon derived from both algal populations increased significantly after 60 days. Although the dissolved organic matter gradually became refractory, the contributions of the algal-derived organic matter to the dissolved organic matter and hydrophobic dissolved organic matter increased. Our laboratory experimental results suggest that algal-derived organic matter produced by phytoplankton and periphytic algae could contribute significantly to the non-biodegradable organic matter through microbial transformations.     

Solar energy for electricity and fuels

Solar energy conversion into electricity by photovoltaic modules is now a mature technology. We discuss the need for materials and device developments using conventional silicon and other materials, pointing to the need to use scalable materials and to reduce the energy payback time. Storage of solar energy can be achieved using the energy of light to produce a fuel. We discuss how this can be achieved in a direct process mimicking the photosynthetic processes, using synthetic organic, inorganic, or hybrid materials for light collection and catalysis. We also briefly discuss challenges and needs for large-scale implementation of direct solar fuel technologies.