A Thermodynamic Geography: Night-Time Satellite Imagery as a Proxy Measure of Emergy

Night-time satellite imagery enables the measurement, visualization, and mapping of energy consumption in an area. In this paper, an index of the “sum of lights” as observed by night-time satellite imagery within national boundaries is compared with the emergy of the nations. Emergy is a measure of the solar energy equivalent used, directly or indirectly, to support the processes that characterize the economic activity in a country. Emergy has renewable and non-renewable components. Our results show that the non-renewable component of national emergy use is positively correlated with night-time satellite imagery. This relationship can be used to produce emergy density maps which enable the incorporation of spatially explicit representations of emergy in geographic information systems. The region of Abruzzo (Italy) is used to demonstrate this relationship as a spatially disaggregate case.     

Feasibility of coupling a thermal/optical carbon analyzer to a quadrupole mass spectrometer for enhanced PM2.5 speciation

A thermal/optical carbon analyzer (TOA), normally used for quantification of organic carbon (OC) and elemental carbon (EC) in PM_2.5 (fine particulate matter) speciation networks, was adapted to direct thermally evolved gases to an electron impact quadrupole mass spectrometer (QMS), creating a TOA-QMS. This approach produces spectra similar to those obtained by the Aerodyne aerosol mass spectrometer (AMS), but the ratios of the mass to charge (m/z) signals differ and must be remeasured using laboratory-generated standards. Linear relationships are found between TOA-QMS signals and ammonium (NH₄⁺), nitrate (NO₃^?), and sulfate (SO₄^2-) standards. For ambient samples, however, positive deviations are found for SO₄^2-, compensated by negative deviations for NO₃^?, at higher concentrations. This indicates the utility of mixed-compound standards for calibration or separate calibration curves for low and high ion concentrations. The sum of the QMS signals across all m/z after removal of the NH₄⁺, NO₃^?, and SO₄^2- signals was highly correlated with the carbon content of oxalic acid (C?H?O?) standards. For ambient samples, the OC derived from the TOA-QMS method was the same as the OC derived from the standard IMPROVE_A TOA method. This method has the potential to reduce complexity and costs for speciation networks, especially for highly polluted urban areas such as those in Asia and Africa.

Implications: Ammonium, nitrate, and sulfate can be quantified by the same thermal evolution analysis applied to organic and elemental carbon. This holds the potential to replace multiple parallel filter samples and separate laboratory analyses with a single filter and a single analysis to account for a large portion of the PM_2.5 mass concentration.     

Correction methods for organic carbon artifacts when using quartz-fiber filters in large particulate matter monitoring networks: the regression method and other options

Sampling and handling artifacts can bias filter-based measurements of particulate organic carbon (OC). Several measurement-based methods for OC artifact reduction and/or estimation are currently used in research-grade field studies. OC frequently is not artifact-corrected in large routine sampling networks (e.g., U.S. Environmental Protection Agency (EPA)'s Chemical Speciation Network). In some cases, the OC artifact has been corrected using a regression method (RM) for artifact estimation. In this method, the gamma-intercept of the regression of the OC concentration on the fine particle (PM2.5) mass concentration is taken to be an estimate of the average OC sampling artifact (net of positive and negative artifacts). This paper discusses options for artifact correction in large routine sampling networks. Specifically, the goals are to (1) articulate the assumptions and limitations inherent to the RM, (2) describe other artifact correction approaches, and (3) suggest a cost-effective method for artifact correction in large monitoring networks. The RM assumes a linear relationship between measured OC and PM mass: a constant slope (OC mass fraction) and a constant intercept (RM artifact estimate). These assumptions are not always valid. Additionally, outliers and other individual data points can have a large influence on the RM artifact estimates. The RM yields results within the range of measurement-based methods for some datasets and not for others. Given that the adsorption of organic gases increases with atmospheric concentrations of organics, subtraction of an average artifact from all samples (e.g., across multiple sites) will underestimate OC for lower-concentration samples (e.g., clean sites) and overestimate OC for higher-concentration samples (e.g., polluted sites). For relatively accurate, simple, and cost-effective artifact OC estimation in large networks, the authors suggest backup filter sampling on at least 10% of sampling days at all sites with artifact correction on a sample-by-sample basis as described herein.     

Spatial and seasonal variations in atrazine and metolachlor surface water concentrations in Ontario (Canada) using ELISA

Concerns regarding the impacts of pesticides on aquatic species and drinking water sources have increased demands on water quality monitoring programs; however the costs of sample analysis can be prohibitive. In this study we investigated enzyme-linked immunosorbent assay (ELISA) as a cost-effective, high through-put method for measuring pesticide concentrations in surface waters. Seven hundred and thirty-nine samples from 158 locations throughout Ontario were analysed for atrazine and metolachlor from April to October 2007. Concentrations ranged from <0.1 to 3.91 μg L⁻¹ (median = 0.12 μg L⁻¹) for atrazine and from <0.1 to 1.83 μg L⁻¹ (median = 0.09 μg L⁻¹) for metolachlor. Peak concentrations occurred in late spring/early summer, in rural agricultural locations, and decreased over the remainder of the growing season for both herbicides. About 3% of the samples that had ELISA results occurring above the limit of quantification (0.10 μg L⁻¹) were evaluated against gas chromatography-mass spectrometry (GC-MS). Linear regression analysis revealed a R² value of 0.88 and 0.39, for atrazine and metolachlor, respectively. ELISA tended to overestimate concentrations for atrazine and metolachlor, most likely because the ELISA kits also detect their metabolites. Atrazine data suggest that ELISA may be used complementary with GC-MS analysis to enhance the spatial and temporal resolution of a water quality monitoring study. The commercially available metolachlor ELISA kit requires further investigation. ELISA may be used to detect atrazine and metolachlor in surface water samples, but it is not recommended as a quantitative replacement for traditional analytical methods.     

Partitioning of perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS) and perfluorooctane sulfonamide (PFOSA) between water and sediment

Laboratory partitioning experiments were conducted to elucidate the sorption behaviour and partitioning of perfluoroalkyl compounds (PFCs). Three different sediment types were used and separately spiked with perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS) and perfluorooctane sulfonamide (PFOSA) at low environmentally realistic concentrations. PFOA, PFOS and PFOSA were mainly distributed in the dissolved phase at low suspended solid concentrations, indicating their long-range transport potential in the marine environment. In all cases, the equilibrium isotherms were linear and the organic carbon normalised partition coefficients (K_OC) decreased in the following order: PFOSA (log K_OC = 4.1 ± 0.35 cm³ g⁻¹) > PFOS (3.7 ± 0.56 cm³ g⁻¹) > PFOA (2.4 ± 0.12 cm³ g⁻¹). The level of organic content had a significant influence on the partitioning. For the sediment with negligible organic content the density of the sediment became the most important factor influencing the partitioning. Ultimately, data on the partitioning of PFCs between aqueous media and suspended solids are essential for modelling their transport and environmental fate.     

Spatial distribution of ciguateric fish in the Republic of Kiribati

Ciguatera is food poisoning caused by human consumption of reef fish contaminated with ciguatoxins (CTXs). The expanding international trade of tropical fish species from ciguatera-endemic regions has resulted in increased global incidence of ciguatera, and more than 50 000 people are estimated to suffer from ciguatera each year worldwide. The Republic of Kiribati is located in the Pacific Ocean; two of its islands, Marakei and Tarawa, have been suggested as high-risk areas for ciguatera. The toxicities of coral reef fish collected from these islands, including herbivorous, omnivorous and carnivorous fish (24% [n = 41], 8% [n = 13] and 68% [n = 117], respectively), were analyzed using the mouse neuroblastoma assay (MNA) after CTX extraction. The MNA results indicated that 156 fish specimens, or 91% of the fish samples, were ciguatoxic (CTX levels >0.01 ng g⁻¹). Groupers and moray eels were generally more toxic by an order of magnitude than other fish species. All of the collected individuals of eight species (n = 3-19) were toxic. Toxicity varied within species and among locations by up to 10 000-fold. Cephalapholis argus and Gymnothorax spp. collected from Tarawa Island were significantly less toxic than those from Marakei Island, although all individuals were toxic based on the 0.01 ng g⁻¹ threshold. CTX concentrations in the livers of individuals of two moray eel species (Gymnothorax spp., n = 6) were nine times greater than those in muscle, and toxicity in liver and muscle showed a strong positive correlation with body weight. The present study provides quantitative information on the ciguatoxicity and distribution of toxicity in fish for use in fisheries management and public health.     

A quantitative risk management framework for dust and hybrid mixture explosions

Dust and hybrid-mixture explosions continue to occur in industrial processes that handle fine powders and flammable gases. Considerable research is therefore conducted throughout the world with the objective of both preventing the occurrence and mitigating the consequences of such events. In the current work, research has been undertaken to help move the field of dust explosion prevention and mitigation from its current emphasis on hazards (with an accompanying reliance on primarily engineered safety features) to a focus on risk (with an accompanying reliance on hierarchical, risk-based, decision-making tools). Employing the principles of quantitative risk assessment (QRA) of dust and hybrid-mixture explosions, a methodological framework for the management of these risks has been developed.The QRA framework is based on hazard identification via credible accident scenarios for dust explosions, followed by probabilistic fault-tree analysis (using Relex – Reliability Excellence – software) and consequence severity analysis (using DESC – Dust Explosion Simulation Code – software). Identification of risk reduction measures in the framework is accomplished in a hierarchical manner by considering inherent safety measures, passive and active engineered devices, and procedural measures (in that order). An industrial case study is presented to show how inherent safety measures such as dust minimization and dust/process moderation can be helpful in reducing dust and hybrid-mixture explosion consequences in a 400-m³ polyethylene storage silo.     

Limitations of recreational camera traps for wildlife management and conservation research: A practitioner’s perspective

The availability of affordable ‘recreational’ camera traps has dramatically increased over the last decade. We present survey results which show that many conservation practitioners use cheaper ‘recreational’ units for research rather than more expensive ‘professional’ equipment. We present our perspective of using two popular models of ‘recreational’ camera trap for ecological field-based studies. The models used (for >2 years) presented us with a range of practical problems at all stages of their use including deployment, operation, and data management, which collectively crippled data collection and limited opportunities for quantification of key issues arising. Our experiences demonstrate that prospective users need to have a sufficient understanding of the limitations camera trap technology poses, dimensions we communicate here. While the merits of different camera traps will be study specific, the performance of more expensive ‘professional’ models may prove more cost-effective in the long-term when using camera traps for research.     

Electro-oxidation of the dye azure B: kinetics,mechanism, and by-products

In this work, the electrochemical degradation of the dye azure B in aqueous solutions was studied by electrochemical advanced oxidation processes (EAOPs), electro-Fenton, and anodic oxidation processes, using Pt/carbon-felt and boron-doped diamond (BDD)/carbon-felt cells with H₂O₂ electrogeneration. The higher oxidation power of the electro-Fenton (EF) process using BDD anode was demonstrated. The oxidative degradation of azure B by the electrochemically generated hydroxyl radicals (^?OH) follows a pseudo-first-order kinetics. The apparent rate constants of the oxidation of azure B by ^?OH were measured according to pseudo-first-order kinetic model. The absolute rate constant of azure B hydroxylation reaction was determined by competition kinetics method and found to be 1.19?×?10⁹ M^?1 s^?1. It was found that the electrochemical degradation of the dye leads to the formation of aromatic by-products which are then oxidized to aliphatic carboxylic acids before their almost mineralization to CO₂ and inorganic ions (sulfate, nitrate, and ammonium). The evolution of the TOC removal and time course of short-chain carboxylic acids during treatment were also investigated.     

Relationship of Destruction Parameters to the Destruction/Removal Efficiency of PCBs

The destruction/removal efficiency (DRE), and the ability to accurately measure it, is a function of the concentration of the chemical compound in the input waste, the incinerator design and operation, sampling methods, and the analytical procedures. All of these are interrelated. This paper discusses the basic DRE equation [DRE = W_In W_out)/W_in × 100] and how it relates to some of the other destruction parameters. Some example data from the literature are presented. While PCBs have been used as the example, the equations and graphs are equally valid for some other hazardous compounds (POHCs), with the substitution of the 99.99% DRE requirement in lieu of the 99.9999% DRE for PCBs. The use of the relationships discussed in this paper should allow incinerator operators to more efficiently plan demonstration test burns which will adequately demonstrate the DRE.