全球液化石油气运输网络贸易社区特征及其演化分析

液化石油气在全球清洁能源消耗市场中扮演着极为重要的角色,其通过船舶在不同港口之间进行运输,而港口之间通过局部密集的运输关系,形成了联系极为紧密的贸易社区。采用复杂网络社区探测方法,基于2013—2017年全球液化石油气船舶轨迹大数据构建运输网络,并对其贸易社区特征及其演化趋势开展分析。结果表明：（1）液化石油气（Liquefied Petroleum Gas,LPG）贸易社区内的港口之间的联系更加紧密,不同社区内的枢纽港口联系也日益紧密;（2）各个贸易社区的规模呈现出增长趋势,且同一社区内的港口在地理空间上变得更为集聚;（3）亚太地区、中东、西北欧和地中海地区形成的社区在全球LPG贸易中一直保持着重要地位,而随着时间推移,美洲社区已逐渐从一个相对孤立的社区发展成为与其他社区存在紧密联系的社区。     

漓江流域δD和δ18O对蒸发的指示作用

以漓江流域为例查明不同水体之间氢氧稳定同位素组成特征,并探讨氢氧稳定同位素对漓江流域的蒸发过程指示作用.结果表明：流域内不同水体之间,氢氧稳定同位素表现出不同的组成特征,地表水和地下水,在丰水期δD值和δ¹⁸O值要比枯水期更容易富集,地下水的δD值和δ¹⁸O值分布范围较地表水小;随着水温的升高,δ¹⁸O的变化趋势比d-excess明显.从漓江上游到下游高程逐渐下降,河水线的斜率和截距也在逐渐减小,其中漓江下游河水线的斜率和截距要低于当地大气降水线,表明下游受到蒸发作用较强烈;地下河水线、地表河水线在一定程度上偏离当地大气降水线,但偏离程度较小,表明三者之间有很好的水力联系.受温度和湿度的共同影响,漓江干流丰水期河水的蒸发量占最初水体总量的0.7%~9.1%,枯水期河水的蒸发量占最初水体总量的2.6%~9.7%,丰水期的蒸发比例低于枯水期,从上游到下游蒸发比例在逐渐上升.研究区蒸发量估算值为959.40mm,与多年实测值少43.11mm,相对误差4.70%.氢氧稳定同位素对研究区降水、地表水、地下水之间的转换规律具有重要的实际意义,在今后的漓江流域水文研究中有着更加广阔的空间.     

邢台市秋季PM2.5及水溶性离子污染特征

为研究邢台市秋季PM_2.5污染特征,于2017年10月15日~11月14日在邢台市区对PM_2.5样品进行了采集,并对其中水溶性离子（包括Cl^-、NO₃^-、SO₄^2-、NH₄⁺、Ca²⁺、Na⁺、Mg²⁺、K⁺）进行了分析.结果显示,观测期间邢台市ρ（PM_2.5）平均值为（130.0±74.9）μg/m³,其中水溶性离子质量浓度为（69.8±11.4）μg/m³,占ρ（PM_2.5）的53.3%,NO₃^-、SO₄^2-和NH₄⁺为主要离子,占水溶性离子比例达到了89.7%. 当污染加重,水溶性离子质量浓度随ρ（PM_2.5）增大而升高,且NO₃^-、NH₄⁺及SO₄^2-占比亦逐渐升高,但其他离子占比随之下降,Ca²⁺尤为明显,表明ρ（PM_2.5）升高时主要受二次无机转化影响;观测期间SOR（硫转化率）与NOR（氮转化率）的平均值分别为0.36和0.25,表明秋季SO₂与NO₂转化速率较强,二次无机污染严重,另外SOR及NOR与温度及相对湿度呈正相关,且SOR对二者更为敏感;邢台市秋季PM_2.5呈弱碱性,NH₄⁺主要以（NH₄）₂SO₄和NH₄NO₃的形式存在;ρ（NO₃^-）/ρ（SO₄^2-）平均值为2.13,表明移动源对秋季大气颗粒物的来源贡献较大;PMF分析结果表明,二次转化源、燃烧源及扬尘源为邢台市秋季PM_2.5中水溶性离子的主要来源.     

北方湖库沉积物重金属区域特征及生态风险评价

以白洋淀、衡水湖、于桥水库、松花湖、大伙房水库和小兴凯湖沉积作为研究对象,通过对北方六湖库沉积物中Cu、Zn、Pb、Cr、Ni等重金属元素进行分析,并与国内外其他水域重金属污染情况进行多因素比较,探讨了六湖库主要重金属污染源的差异性,区域分布特征以及与国内外其他水域污染的相似性和区别.结果表明,六湖库沉积物重金属污染处于中等偏下水平.六湖库之间主要重金属污染源存在差别.沉积物重金属含量未出现明显上升的趋势.其中Zn、Pb存在富集现象,但Pb含量与历史数据相比出现下降,Zn的含量与其他地区相比整体偏高.大伙房水库沉积物重金属污染较重,Cu、Zn、Pb、Cr、Ni含量平均值分别为56.28,142.3,17.44,97.9,44.44mg/kg.小兴凯湖沉积物重金属含量最低,Cu、Zn、Pb、Cr、Ni含量平均值分别为2.41,63.90,13.37,56.36,26.09mg/kg.六湖库综合风险评价结果为大伙房水库>于桥水库>白洋淀>衡水湖>松花湖>小兴凯湖,重金属整体潜在生态风险指数为低.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Analytical methods and environmental processes of nanoplastics

The degradation of plastic debris may result in the generation of nanoplastics (NPs). Their high specific surface area for the sorption of organic pollutions and toxic heavy metals and possible transfer between organisms at different nutrient levels make the study of NPs an urgent priority. However, there is very limited understanding on the occurrence, distribution, abundant, and fate of NPs in the environment, partially due to the lack of suitable techniques for the separation and identification of NPs from complex environmental matrices. In this review, we first overviewed the state-of-the-art methods for the extraction, separation, identification and quantification of NPs in the environment. Some of them have been successfully applied for the field determination of NPs, while some are borrowed from the detection of microplastics or engineered nanomaterials. Then the possible fate and transport of NPs in the environment are thoroughly described. Although great efforts have been made during the recent years, large knowledge gaps still exist, such as the relatively high detection limit of existing method failing to detect ultralow masses of NPs in the environment, and spherical polystyrene NP models failing to represent the various compositions of NPs with different irregular shapes, which needs further investigation.     

基于最大熵模型的福建省红树林潜在适生区评估

本研究利用生物气候、地形、底质类型、海温等环境因子和红树林分布数据建立了福建省红树林分布模型,基于最大熵方法分析了福建省沿岸红树林潜在适生区的空间分布.根据模型输出结果对福建省红树林的生境适宜性进行了评估,识别了影响红树林分布的关键环境因子及其适生值区间,并通过空间叠加分析获取了福建省红树林保护与修复的优先区与空缺区域.结果表明,影响福建省红树林适生区分布格局的主要环境因子包括海表温度、气温和降水等,福建省红树林潜在适生区主要位于沙埕港-三沙湾-兴化湾沿岸、泉州湾-厦门湾-九龙江口沿岸、漳江口-东山湾沿岸等地,其中最优适生区面积约为91km².全省共识别出8处红树林保护与修复的优先区域,现存红树林保护率约为64.4%,保护修复空缺主要出现在沙埕港、三沙湾、罗源湾、福清湾等处,研究结论可为未来福建省红树林保护和修复行动提供科学参考.