SAFEST TO TRAVEL BY BICYCLE,CAR, OR BIG TRUCK?

This study compares highway crash incidence, injuries, and costs by vehicle type. Annual crash and injury incidence were estimated using Crashworthiness Data System (1988-1991), National Automotive Sampling System (1982-1986), General Estimates System (1992-1993), and Fatal Analysis Reporting System (1993) data. Costs were computed based on restraint use, body region, and threat-to-life severity of the injury. Costs were then allocated between vehicle types using three different methods in order to answer comparative safety questions. Motor vehicle and bicycle crash costs total $389 billion annually; 75% resulting from passenger vehicles. Motorcycles and bicycles have the highest costs per 1000 vehicle and passenger miles; costs per victim are highest for pedestrians, bicyclists, and motorcyclists. Costs per vehicle mile for heavy trucks and passenger cars are comparable but exceed costs for light trucks. Passenger vehicle occupants are safest if a crash occurs. Light truck, other single truck, and bus occupants have the lowest cost per passenger mile, but higher costs than air and rail travelers. Motorcyclists face the greatest risks. Combination trucks may not impose an excess risk to other drivers, but their drivers face large risks.     

Defending the Wrist Deviation Test for Carpal Tunnel Syndrome Screening: A Comparison of Vibration Thresholds and Distal Motor Latency

This research used distal motor latency (DML) and vibration thresholds (VT) to evaluate 84 hand activity and wrist deviation combinations to determine the best association with carpal tunnel syndrome (CTS). Female volunteers, 2 healthy and 2 CTS diagnosed, were age matched and operated a keyboard for 4 hrs a day. Room temperature was 28°C(±2). Beginning DML and VT were taken with a relaxed neutral posture hand. The wrist was deviated in a randomly selected combination, and determinations were taken at 5-min intervals. The trial ended at 20 min or when discomfort was felt. The CTS conditions were discriminated by pain four times, DML once, and VT 14 times. Vibrometry was the most consistent CTS discriminator. The best VT results for wrist positions were obtained with wrist extension and extended extension, whereas the unclenched, clenched, and loaded power grip activities proved to be the most consistent hand activities.     

Physical Effects of New Devices for Bricklayers

Bricklaying is a physically demanding job. Bricklayers frequently flex their trunk to pick up bricks and mortar and position these in a wall. The experienced workload is highest working with bricks at 0 to 50 cm from the floor. In this study the effects of 2 devices that have proven to be feasible in practice are evaluated.

The 50 cm raise due to the 2 devices is experienced as comfortable, the estimated lumbar compression force was reduced, and observations indicate likewise. It is discussed that the field experiments have many drawbacks. Nevertheless, based on this study in combination with other literature the improvements could be recommended.     

Driver Workload Response to In-Vehicle Device Operations

A central concern of Intelligent Transportation Systems (ITS) is the effect of in-vehicle devices (e.g., cell phones, navigation systems, radios, etc.) on driver performance and safety. As diverse and innovative technologies are designed and implemented for in-vehicle use, questions regarding the presence and use of these devices assume progressively greater importance. Further concerns for advanced driver training require us to develop and validate reliable and effective procedures for assessing such effects. This work examines a number of candidate procedures, in particular the evaluation of change in cognitive workload as a strategy by which such goals might be achieved.     

A Study of Computer-Based Task Performance Under Thermal Stress

A visual-visual dual computer task was designed to test the effect of the thermal environment on dual task performance. The temperatures selected for testing were 20 and 35 °C Wet Bulb Globe Temperature (WBGT). 34 volunteers were randomly assigned to 1 of the 2 temperature conditions. Individual differences in single task performance were controlled by equating the baselines of single task performance. Once individual differences in single task capacity were controlled, statistically significant differences in performance were demonstrated. Mean accuracy was computed over a 1-hr testing period in each temperature condition. Participants’ mean accuracy in the 35° condition (38.18%) was substantially lower than in the 20° condition (50.88%).     

Assessment of an accidental vapour cloud explosion: Lessons from the Indian Oil Corporation Ltd. accident at Jaipur,India

On 29 October 2009, at 19:30 IST, a devastating vapour cloud explosion occurred in a large fuel storage area at the Indian Oil Corporation (IOC) Depot in Jaipur, India, generating significant blast pressure. As a consequence of this explosion, the entire installation was destroyed, buildings in the immediate vicinity were heavily damaged, and windowpane breakages were found up to 2 km from the terminal. The IOC estimated that the total loss from the fire and explosion was approximately INR 2800 million.Ironically, as a storage site, the Jaipur terminal was not highly congested, and thus was not considered to have adequate potential for a vapour cloud explosion (VCE). Nevertheless, the prima facie evidences indicate that this was a case of VCE. Therefore, the main objective of this study is to quantify the potential overpressures due to vapour cloud explosions (VCEs) using the Process Hazard Analysis DNV Norway based PHAST 6.51 Software. The results are validated by the extent of the damage that had occurred. The estimation of the VCE shows that a maximum 1.0 bar overpressure was generated in the surrounding area. The initial assessment of the accident data roughly estimates the release mode, time, and amount of vaporized fuel. A more accurate estimate has been obtained by modelling the dispersion of vapour clouds in the surrounding atmosphere, which reveals trends and relationships for the occurrence of vapour cloud explosions.     

Small-scale physical explosions in shock tubes in comparison with condensed high explosive detonations

A series of small-scale experiments involving physical explosions in a 1.6 l pressure vessel was carried out. Explosions were initiated by spontaneous rupture of an aluminium membrane on one side of the vessel at a pressure in the range 1–1.2 MPa. The pressure waves released were measured at different distances along two separate shock tubes, one 10 m long and 200 mm in diameter (closed at one end by the high pressure vessel) and the other 15 m long and 100 mm in diameter.TNT equivalency was used for predicting the blast wave characteristics after vessel rupture. TNT equivalency was used because equations for prediction of peak pressure and impulse of the blast wave in 1-D geometry after detonations of condensed explosives are known. Some experiments with an equivalent amount of real explosive were carried out for comparison with the theoretical and experimental data obtained. The applicability of the TNT equivalency method presented for calculations of maximum pressure and shock wave impulse generated after rupture of the pressure vessel in 1-D geometry is discussed.     

Environmental risk mapping of accidental pollution and its zonal prevention in a city

Accidental releases of pollution can have severe environmental, societal, economic, and institutional consequences. This paper considers the use of risk mapping of accidental pollution events, and zonal prevention measures for alleviating the impact on large urban areas. An Environmental Pollution Accident Risk Mapping (EPARM) model is constructed according to a mapping index system supported by quantitative sub-models dedicated to evaluating the risk arising from different sources of potential accidental pollution. The EPARM approach consists of identifying suitable indexes, assessment of environmental risk at regional and national scales based on information on previous pollution accidents and the prevailing environmental and social conditions, and use of GIS to map the overall risk. A case study of pollution accidents in Minghang District, Shanghai, China is used to demonstrate the effectiveness of the model. The paper also proposes a systemic framework for accidental environmental pollution risk prevention, and detailed countermeasures for specific risk zones.