Biogenic Sulfur Gas Emissions from Soils in Eastern and Southeastern United States

Data are presented for the first systematic measurements of biogenic sulfur gas flux from the major soil orders within the eastern and southeastern United States. Sulfur flux samples were collected and analyzed on-site during the fall of 1977, spring and summer of 1978 and summer of 1979. A total of 27 sampling locales in 17 states were examined. Eight additional sites were visited in 1980.

At some locales, two to four soils were examined, providing an even broader sampling of the soil orders. Three of the locales were revisited two or three times during the course of the study to establish the influence of seasonal climatology upon the measured emission rates and chemical composition of the sulfur flux mixtures.

The sulfur gas enhancement of sulfur-free sweep air passing through dynamic emission flux chambers placed over selected sampling areas was determined by combined cryogenic enrichment sampling and wall-coated, open tubular, capillary column, cryogenic gas chromatography (WCOT/GC) using a sulfur selective, flame photometric detector (FPD).

Sulfur gas mixtures varied with soil order, ambient temperature, insolation, soil moisture, cultivation, and vegetative cover. Statistical analyses indicated strong temperature and soil order relationships for sulfur emissions from soils.

Fluxes ranged from 0.001 g to 1940 g of total sulfur as S/m²/yr. The calculated mean annual sulfur flux, weighted by soil order, was 0.03 g S/m²/yr for the study land area, or 110,872 metric tons (mT). The estimated annual average sulfur flux increased from 65 mT per 6400 km² for the land grids in the northernmost east-west grid tier to an average 1800 mT for the land grids in the southern Florida grid tiers.

This systematic sampling of major soils provides a much broader data base for estimating biogenic sulfur flux than previously reported for isolated intertidal sites, and presents the first sulfur flux estimates for inland soils which make up approximately 93% of the land of the eastern United States.     

experience of the forest products industry in obtaining air quality permits for new and modified sources

A detailed study of the air quality permitting process for 65 different forest products industry projects requiring preconstruction permit approvals from EPA, state, and local air pollution control agencies was conducted. The projects included a wide array of sources including kraft recovery furnaces, lime kilns, fossil fuel and wood residue fired boilers, solid wood products manufacturing facilities, paper coaters, and printing presses. Information concerning the time involved in the permitting process, costs associated with obtaining the permits, use of air quality models and ambient monitoring data, emission control technology determinations, problem areas encountered during the permitting process, perceived benefits and drawbacks of the permitting process, and the effect of permitting requirements on project planning was obtained.

The results indicate that certain permitting requirements such as Best Available Control Technology (BACT) determinations, dispersion modeling results, and use of ambient air quality monitoring data seldom influence the emission limitations ultimately imposed in the final approved permit, with 87% of the final emission limits equivalent to the applicable New Source Performance Standard (NSPS). The 65 permitting case histories also show that obtaining permits for projects subject to Prevention of Significant Deterioration (PSD) requirements takes approximately twice as long and costs twice as much as obtaining permits for projects not subject to PSD requirements.     

Change in Pulmonary Function in Children Associated with Air Pollution Episodes

Pulmonary function of approximately 200 school children in Steubenville, OH was measured before and immediately following air pollution alerts in the fall of 1978 and 1979. TSP concentrations exceeded the National Primary Ambient Air Quality 24 h standards in 1978. SO₂ exceeded the standard in 1979. The children were then reexamined in three weekly visits following each alert. Estimated mean Forced Vital Capacity (FVC) was approximately 2% lower following each alert, although the lowest means were observed one to two weeks after the episodes. Forced Expired Volume in 0.75 sec (FEV_0.75) did not change during the 1978 study, but was 4% lower immediately following the 1979 alert. The children were measured again in five weekly examinations in the spring and fall of 1980. Air pollution levels did not exceed the standards on either occasion. In the spring of 1980, estimated mean FVC and FEV_0.75 showed a decline similar to that observed following the alerts in 1978 and 1979. In the fall of 1980, there were no significant differences in the estimated mean FVC or FEV_0.75 between the examinations. A total of 335 children were tested in the four studies, including 194 who participated in more than one study. The evidence for each child from all the studies was combined in a regression analysis of pulmonary function on TSP and SO₂ average concentrations in the previous 24 h. The distribution of the individual regression coefficients was centered significantly below zero, implying a decrease in pulmonary function with increasing TSP and SO₂ concentrations. The magnitude of the median change was less than 1% of the mean FVC and FEV_0.75 over the range of TSP and SO₂ concentrations observed.     

The Effect of Building Fan Operation on Indoor-Outdoor Dust Relationships

As part of an energy conservation program recently implemented by the Bell System, fans in many telephone equipment buildings now operate only when necessary to bring the temperature within allowable limits, rather than continuously. In the study reported here the effects of fan operation on indoor-outdoor dust relationships were monitored at 2 representative telephone offices. Automatic dichotomous samplers were used to collect fine and coarse aerosol particles inside telephone equipment buildings at Wichita, KS and Lubbock, TX. At both sites, outdoor samples (roof top) were collected at the same time as the indoor samples. During the tests the building fans were repetitively cycled between 2-week intervals of continuous fan operation and 2-week intervals of intermittent fan operation. The indoor dust concentrations typically increased when the fans were off. The results indicate that this increase was due to loss of constant filtration, but not due to loss of building pressurlzation (i.e., filtration of the recirculated air is largely responsible for the lower dust levels when the fans are running continuously). An expression is derived for the relative dust increase when the building fans are switched off. Among other factors, the relative increase is directly proportional to the efficiency of the building filters and to the rate at which air is recirculated through them. The present findings can be extended to similar buildings.     

Comparison of Air Pollutant Emissions from Vaporizing and Air Atomizing Waste Oil Heaters

Information presented in this paper is directed to individuals concerned with emissions from combustion of waste crankcase oil for space heating. Studies were performed to characterize gaseous and particulate emissions and vaporizing pot solid residues resulting from the combustion of waste crankcase oil. Two types of waste oil burners were tested. One was a vaporizing oil burner rated at 35.2 kW (120,000 Btu/h heat input), and the other was an air atomizing oil burner rated at 73.3 kW (250,000 Btu/h heat input). Except for NO_X and SO_X, gaseous emissions were similar to those from conventional distillate oil combustion. NO_X and SO_X emissions were higher due to higher fuel nitrogen and sulfur concentrations. Waste oil from automotive use showed higher inorganic levels than crankcase oil used for truck engine lubrication. Both burner types discharged high levels of metallic species, but the air atomizing unit had much higher stack emission levels than did the vaporizing pot system. Also, particulate loading levels were an order of magnitude higher for the air atomizing burner than for the vaporizing pot burner when firing the waste oils. However, the vaporizing pot burner generated a waste residue containing the majority of its elemental emissions. Elements which exceeded threshold limit values for one or both heaters were cadmium, chromium, cobalt, copper, iron, lead, nickel, phosphorus, and zinc. However, the nickel and much of chromium appeared to be a sampling artifact caused by the stainless steel sampling system.     

Evaluation of Selected Gaseous Halocarbons for Use in source Test Performance Audits

A repository of 38 gaseous organic compounds in compressed gas cylinders has been established by EPA. This repository was established to provide standards for source test performance audits, that is, quantitative quality assurance tests. Among these compounds are ten halogenated organic species, which are the focus of this paper.

Stability studies of all ten compounds have been performed to determine the feasibility of using them as performance audit standards. Results indicate that all of the halocarbons tested are adequately stable to be used as reliable audit standards.

Subsequent to completion of stability studies, four of the ten halocarbons were used in source test performance audits. Results are available at this time for two of the four compounds; the results show agreement within 10% of the concentrations previously established by Research Triangle Institute.     

A Method for Predicting the Effective Volume Resistivity of a Sodium Depleted Fly Ash Layer

Research has been conducted to develop a technique for predicting the effective volume resistivity of a fly ash layer that has been exposed to circumstances leading to a hot-side precipitator problem known as sodium depletion. Eight fly ashes, representing a major portion of U.S. coals, were evaluated by subjecting 0.5 cm ash layers to a continuously applied voltage gradient of 4 kV/cm for periods of time up to 35 days at a temperature of 350°C (662°F). Resistivity was determined at 350°C before the test started and after the long period of applied voltage used to create the sodium depleted situation. In this condition, resistivity was also determined at 280°C (536°F) for an average electric field Intensity of 4 kV/cm and immediately prior to breakdown. This experimental method can be used with any ash sample to estimate resistivity In a sodium depleted condition. But in addition, a correlation resulting from these resistivity data has been developed. This correlation Is combined with an existing technique for predicting resistivity to produce a method for calculating the expected ash layer resistivity after sodium depletion has occurred.     

Hazardous Waste Minimization: Part IV Waste Reduction in the Metal Finishing Industry

The metal finishing industry uses over 40 production processes to produce a wide range of metal products. Waste streams generated include wastewater, waste oils, spent solvents, and spent process solutions. Currently a wide variety of techniques which minimize waste are available. Cost-effective methods to reduce electroplating wastewater contamination include water conservation and drag-out reduction, recovery and management. Ways to cost-effectively reduce the generation of spent metal-working fluids include establishing a fluid management program and installing a fluid recovery system. However, before any techniques are selected, a waste reduction survey should first be conducted.     

An Evaluation of the Semi-VOST Method for Determining Emissions from Hazardous Waste Incinerators

The Semi-Volatile Organic Sampling Train method was investigated to determine its reliability and to determine the bias and precision of the method when used to determine emissions from hazardous waste incinerators. Experiments showed that the matrix and sampling variables usually involved in sampling emissions from a hazardous waste incinerator had no significant effect on the recovery of 11 different organic compounds. Significant losses of the sampled compounds can occur during sample preparation. The degree of loss appears to be directly related to the compounds, vapor pressure. These losses can be corrected for by adding deuterated surrogates to the sample and analyzing the surrogates along with the native compounds.

The bias determination was based on dynamic spiking of the sampling train with five deuterated organic compounds selected from Appendix VIII of the Resource Conservation and Recovery Act regulations. The results show biases of from -1 ± 8 percent to -18 ± 27 percent for chlorinated and nonchlorinated compounds. Pyridine, a water-soluble compound, showed a larger bias of-29 ± 13 percent. Particular attention to the recovery of water soluble compounds is necessary to minimize bias in their determinations. Further work is needed to determine the reliability of laboratory-determined retention volumes that are used to determine sampling conditions.