Rotary Kiln Incineration II. Laboratory-Scale Desorption and Kiln-Simulator Studies—Solids

With landfill costs increasing and regulations on landfilling becoming more stringent, alternatives to conventional hazardous waste treatment strategies are becoming more desirable. Incineration Is presently a permanent, proven solution for the disposal of most organic contaminants, but also a costly one, especially in the case of solids which require some auxiliary fuel. The goal of this research is to develop an understanding of the phenomena associated with the evolution of contaminants from solids In the primary combustor of an Incineration system. A four-fold approach is being used. First, a bench-scale particle characterization reactor was developed to study the transport phenomena on a particle basis, where the controlling processes are mainly intraparticle. Second, a bed-characterization reactor was built to examine the controlling transport phenomena within a bed of particles, where the processes are primarily interparticle. The results of these studies can be applied to any primary combustor. A pilot-scale rotary kiln was developed to study the evolution of contaminants from solids within a realistic temperature and rotation environment. Finally, in situ measurements are being obtained from a full-scale rotary-kiln.

This paper describes results obtained in a study using a commercial sorbent contaminated with toluene. The data are from the particle-characterization reactor and the rotary-kiln simulator. The results show that the method of contamination and charge size do not have a large effect on desorption, while temperature and contaminant concentration are important parameters In the evolution of contaminants in a rotary kiln.     

Determination of Room Temperature OH Rate Constants for Acetylene,Ethylene Dichloride,Ethylene Dibromide,p-Dichlorobenzene and Carbon Disulfide

A relative rate procedure was used to measure hydroxyl rate constants at room temperature in the presence of oxygen. The photolysis of methyl nitrite in the presence of nitric oxide was used to generate OH radicals. The rate of loss of the test compounds was measured relative to that of ethane (k_OH = 2.74 × 10^-13 cm³ molec^-1 s^-1). The rates obtained at 297 ± 2 K are: acetylene = (7.8 ± 1.6) × 10^-13 cm³ molec^-1 s^-1,1,2-dichloroethane (2.8 ± Q.6) × 10^-13 cm³ molec^-1 s^-1, 1,2-dibromoethane (2.4 ± 0.5) × 10^-13 cm³ molec^-1 s^-1, p-dichlorobenzene (4.3 ± 0.9) × 10^-13 cm³ molec^-1 s^-1 and carbon disulfide (29 ± 6) × 10^-13 cm³ molec^-1 s^-1. Under a proposed EPA rule, this OH rate determination procedure could be used to determine if a given volatile organic will be subject to control for reduction of photochemical ozone.     

Transportation-Related Volatile Hydrocarbon Source Profiles Measured in Atlanta

Abstract

Samples representative of transportation-related hydrocarbon emissions were collected as part of the 1990 Atlanta Ozone Precursor Monitoring Study. Motor vehicle emissions were sampled in canisters beside a roadway in a tunnel-like underpass during periods of heavy traffic. Airport and aircraft emissions were approximated by canister samples obtained at a major airport facility. Three octane grades of gasoline were purchased from six major vendors in Atlanta. Canister samples were prepared using these fuels to approximate the whole gasoline and gasoline vapor composition of the fuels in use during the study. All samples were analyzed by gas chromatography/flame ionization detection (GC/FID) for their hydrocarbon content. Detailed speciated hydrocarbon profiles were developed from this source sampling and analysis program for use in the Chemical Mass Balance (CMB) model. Profiles presented and discussed here represent the hydrocarbon composition of emissions from a roadway, composite headspace gasoline at two temperatures, composite whole gasoline, whole gasoline at three octane grades, and an airport. The roadway profile is compared with similar profiles in the literature, and recommendations are made regarding its use in the CMB model. The roadway and fuel profiles are discussed in the context of the MOBILE5 model outputs. The headspace gasoline vapor profile presented here is compared with a headspace gasoline vapor profile calculated from the whole gasoline profile by means of Raoult’s law. Agreement between the measured and calculated headspace profiles is excellent. The airport profile demonstrates the importance of high molecular weight volatile hydrocarbons in airport and aircraft emissions.     

Spatial Variation in Acidic Sulfate and Ammonia Concentrations within Metropolitan Philadelphia

Abstract

Acidic sulfate concentrations were measured in metropolitan Philadelphia during the summers of 1992 and 1993, as part of a continuing effort to characterize particle concentrations in urban environments. Sampling was performed simultaneously at eight sites located within and around metropolitan Philadelphia. Sites were selected based on their population density and on their distance and direction from the city center. Air pollution sampling was conducted every other day during the summer of 1992 and every day during the summer of 1993. All samples were collected for 24-h periods beginning at 9 a.m. (EDT). All acidic sulfate and ammonia samples were collected using modified Harvard-EPA Annular Denuder Systems (HEADS).

In this paper, we examine the spatial variation in acidic sulfate and ammonia concentrations within the metropolitan Philadelphia area. We also identify factors that may influence their variation and develop models to predict their concentrations. Outdoor sulfate (SO₄ ^2?) concentrations were uniform within metropolitan Philadelphia; however, aerosol strong acidity (H⁺) concentrations varied spatially. This variation generally was independent of wind direction, but was related to local factors, such as the NH₃ concentration, population density, and distance from the center of the city. Physico-chemical models, which were developed using data collected during the summer of 1992, were excellent predictors of 24-h and mean summertime H⁺ concentrations measured during the summer of 1993. Models accounted for 78% of the variation in 24-h H⁺ levels. Results suggest that a single stationary ambient (SAM) monitor would be sufficient to estimate SO₄ ^2? exposures for populations living in Philadelphia. For H⁺, however, multiple monitoring sites or models should be used to determine the outdoor H+ exposures of populations living in urban environments, although a single SAM site may provide an excellent index of H⁺ variation over time.     

Airborne Particulate Emissions from a Chromic Acid Anodizing Process Tank

Particulate mass concentration, particle size distribution, and particle chemical composition measurements have been conducted on the gases exhausting from a chromic acid anodizing process tank. Particle mass concentrations in the 200 to 20,000 μg/m³ range were measured using open-faced filters (47 mm diameter) adjacent to the process tank liquid and with closed filters (90 mm diameter) in the exhaust duct. Particle size distributions, measured using University of Washington Mark 3 and Mark 20 Cascade Impactors, showed the particle aerodynamic mass median diameter was about 3 microns. Chemical analysis of the particle samples obtained by the Modified EPA Method 5 sampling train, the Mark 20 UW Cascade Impactors, and by the 47 mm and 90 mm diameter filters showed Cr⁺⁶ concentrations in the 20 to 1,500 μg/m³ range with over 99 percent of the chromium in particles larger than 1.0 microns diameter. An integrating nephelometer was used to measure the light scattering coefficient of the exhaust gases upstream of the wet scrubber. The light scattering coefficient increased by a factor of about 2–3 over the background level during the 40 minute time period while a part was being anodized. The bscat values ranged from 3 × 10^?5 to 3 × 10^?4 meters^?1 for the aerosol particles less than about 6 microns aerodynamic diameter.     

Measurement of Volatile Organics at Part per Billion Concentrations Using a Cold Trap Inlet and High Speed Gas Chromatography

Direct inlet gas chromatography (GC) is becoming one of the most frequently used techniques for measurement of volatile organics in air. Although GC is an effective tool, its usefulness as a field method can be limited by retention times of several minutes or more, and by the limits of detection. In order to address these issues, a high speed GC system featuring a capillary cold trap inlet and variable speed electrometeramplifier was developed and tested.

The gas cooled inlet was used to collect and focus organic vapors from injection volumes of up to 1 ml. Resistance heating of the metal cold trap produced a narrow injection band that allowed simple separations to be completed in 5 to 20 seconds. Use of a variable speed electrometer-amplifier allowed the response time and noise suppression characteristics to be adjusted to the needs of the specific analysis.

Simple mixtures of organics including aromatics, alkanes and chlorinated hydrocarbons were separated in 20 seconds or less. The limits of detection for 13 test compounds ranged from less than 1 part per billion by volume (ppbv) to about 50 ppbv. Data presented here indicate that high speed GC using a cold trap inlet may be a feasible approach for near real-time measurement of volatile organics in ambient air.     

Estimating Maximum Concentrations for Open Path Monitoring Along a Fixed Beam Path

ABSTRACT

Researchers have applied open path optical sensing techniques to a variety of workplace and environmental monitoring problems. Usually these data are reported in terms of a path-average (or path-integrated) concentration. When assessing potential human exposures along a beam path, this path-average value is not always informative, since concentrations along the path can vary substantially from the beam average. The focus of this research is to arrive at a method for estimating the upper-bound in contaminant concentrations over a fixed open beam path. The approach taken here uses a statistical model to estimate an upper-bound concentration based on a combination of the path-average and a measure of the spatial variability computed from point samples along the beam path. Results of computer simulations and experimental testing in a controlled ventilation chamber indicate that the model produced conservative estimates for the maximum concentration along the beam path. This approach may have many applications for open path monitoring in workplaces or wherever maximum concentrations are a concern.     

Modeling Emissions from Elevated Cylindrical Bins

Abstract

This paper demonstrates how wind tunnel modeling data that accurately describe plume characteristics near an unconventional emission source can be used to improve the near-field downwind plume profiles predicted by conventional air pollution dispersion models. The study considers a vertical, cylindrical-shaped, elevated bin similar to large product storage bins that can be found at many industrial plant sites. Two dispersion models are considered: the U.S. Environmental Protection Agency's ISC2(ST) model and the Ontario Ministry of the Environment and Energy's GAS model. The wind tunnel study showed that plume behavior was contrary to what was predicted using conventional dispersion models such as ISC2(ST) and GAS and default values of input parameters. The wind tunnel data were used to develop a protocol for correcting the dispersion models inputs, resulting in a substantial improvement in the accuracy of the dispersion estimates.     

Characterization of Fine Particulate Matter Produced by Combustion of Residual Fuel Oil

ABSTRACT

Combustion experiments were carried out on four different residual fuel oils in a 732-kW boiler. PM emission samples were separated aerodynamically by a cyclone into fractions that were nominally less than and greater than 2.5 |j.m in diameter. However, examination of several of the samples by computer-controlled scanning electron microscopy (CCSEM) revealed that part of the PM_2.5 fraction consists of carbonaceous cenospheres and vesicular particles that range up to 10 |j.m in diameter. X-ray absorption fine structure (XAFS) spectroscopy data were obtained at the S, V, Ni, Fe, Cu, Zn, and As K-edges and at the Pb L-edge. Deconvolution of the X-ray absorption near edge structure (XANES) region of the S spectra established that the dominant molecular forms of S present were sulfate (26-84% of total S) and thiophene (13-39% of total S). Sulfate was greater in the PM_2.5 samples than in the PM₂₅₊ samples. Inorganic sulfides and elemental sulfur were present in lower percentages. The Ni XANES spectra from all of the samples agreed fairly well with that of NiSO₄, while most of the V spectra closely resembled that of vanadyl sulfate (VO?SO₄?xH₂O). The other metals investigated (i.e., Fe, Cu, Zn, and Pb) also were present predominantly as sulfates. Arsenic was present as an arsen-ate (As⁺⁵). X-ray diffraction patterns of the PM_2.5 fraction exhibit sharp lines due to sulfate compounds (Zn, V, Ni, Ca, etc.) superimposed on broad peaks due to amorphous carbons. All of the samples contain a significant organic component, with the loss on ignition (LOI) ranging from 64 to 87% for the PM_2.5 fraction and from 88 to 97% for the PM_2.5+ fraction. Based on ¹³C nuclear magnetic resonance (NMR) analysis, the carbon is predominantly condensed in graphitic structures. Aliphatic structure was detected in only one of seven samples examined.