Exposure to Methyl Methacrylate and Its Subjective Symptoms Among Dental Technicians,Tehran, Iran

Exposure to methyl methacrylate (MMA), total dust and health symptoms were investigated in 20 dental laboratories located in Tehran, Iran. Time-weighted average (TWA) of MMA and peak concentrations were determined, using XAD-2 tubes followed by GC-ID analysis. Total dusts were evaluated gravimetrically. Health symptoms were asked using a questionnaire. TWA for technicians with direct and indirect exposure to MMA were 327.28 ± 79.42 and 282.9 ± 41.84 mg/m³ , respectively. Peak concentration of MMA for those technicians were 337.0 ± 36.81 and 328.88 ± 45.40 mg/m³, respectively.

There were no significant differences between TWA of MMA and peak concentration in different weekly workdays; however, within-day variations were observed (P < .05).

TWA of MMA and peak concentration correlation with the laboratory volume were 0.61-0.65. Dust exposure of technicians was 2.35 ± 2.70 mg/m³. Cough and skin dryness were the common health symptoms. Smoking and asbestos exposure history were factors influencing cough prevalence (p < .05).

It is concluded that the current Short-Term Exposure Limit (STEL) is not low enough to protect technicians against the adverse effects caused by MMA.     

Radioactivity and radiological risk associated with effluent sediment containing technologically enhanced naturally occurring radioactive materials in amang (tin tailings) processing industry

The processing of amang, or tin tailings, for valuable minerals has been shown to technologically enhance NORM and this has stirred significant radiological safety and health concerns among Malaysia's regulatory authority. A growing radiological concern is now focused on the amang effluent containing NORM in recycling ponds, since these ponds may be reclaimed for future residential developments. A study was carried out to assess the radiological risk associated with amang processing and the accumulated effluent in the recycling ponds. Twenty-six sediment samples from the recycling ponds of two amang plants in the states of Selangor and Perak, Malaysia, were collected and analyzed. The maximum activity concentrations of (238)U, (226)Ra, (232)Th and (40)K recorded in sediments from these ponds were higher than Malaysia's and the world's natural highest. Correspondingly, the mean radium equivalent activity concentration indices, Ra(eq), and gamma radiation representative level index, I(gammar), were higher than the world's average. The enhancement of NORM in effluent sediments as a consequence of amang processing, and the use of a closed water management recycling system created Effective Dose Rates, E (nSv h(-1)), that signal potential environmental radiological risks in these ponds, should they be reclaimed for future land use.     

Inbreeding and the evolution of sociality in arthropods

Animals have evolved strategies to optimally balance costs and benefits of inbreeding. In social species, these adaptations can have a considerable impact on the structure, the organization, and the functioning of groups. Here, we consider how selection for inbreeding avoidance fashions the social behavior of arthropods, a phylum exhibiting an unparalleled richness of social lifestyles. We first examine life histories and parental investment patterns determining whether individuals should actively avoid or prefer inbreeding. Next, we illustrate the diversity of inbreeding avoidance mechanisms in arthropods, from the dispersal of individuals to the rejection of kin during mate choice and the production of unisexual broods by females. Then, we address the particular case of haplodiploid insects. Finally, we discuss how inbreeding may drive and shape the evolution of arthropods societies along two theoretical pathways.     

An equal sex ratio followed by differential sex mortality causes overestimation of females in gall midges: no evidence for sex ratio regulation

Monogeny, the production of unisexual broods by individual females, has been recognized for nearly 80?years. The genetic nature of gall midges' sex determination predicts an equal numbers of male-producing and female-producing females in the populations such that the overall sex ratio is expected to be nearly 1:1. However, observations of some strictly monogenous populations with biased sex ratio, mainly toward females, have raised the question of whether gall midges are able to adjust their offspring sex ratio in response to changes in environmental conditions, and some authors have even considered sex ratio regulation as a strong force in the course of the evolution of monogeny. In this paper, first, by studying the sex ratio variations of the predatory gall midge, Aphidoletes aphidimyza within a generation, we showed that adult males emerge up to 1?day earlier and have shorter life span than females (less than 4?days and up to 6?days, respectively). Although, the sex ratio of A. aphidimyza at the time of emergence was nearly 1:1 (52.41?% males), a simple population simulation indicated that the differential mortality of sexes can lead to a female-biased sex ratio estimation (57.88?% females) under random sampling in the natural environments. Our results imply that the primary sex ratio of monogenous gall midges is nearly 1:1 and that the arrhenogenic/thelygenic gall midges are not able to alter the number of their male/female progenies in response to changes in environmental conditions.     

Stand-alone PV-hydrogen energy system in Taleghan-Iran using HOMER software: optimization and techno-economic analysis

One of the most attractive features of hydrogen as an energy carrier is that it can be produced from water. Hydrogen has the highest energy content per unit mass as compared to chemical fuel and can be substituted. Its burning process is non-polluting, and it can be used in the fuel cells to produce both electricity and useful heat. Photovoltaic arrays can be used in supplying the water electrolysis systems by their energy requirements. During the daylight hours, the sunlight on the photovoltaic array converts into electrical energy which can be used for electrolyzer. The hydrogen produced by the electrolyzer is compressed and stored in hydrogen vessel and provides energy for the fuel cell to meet the load when the solar energy is insufficient. This study investigates a stand-alone power system that consists of PV array as power supply and electrolyzer. They have been integrated and worked at the Taleghan renewable energies’ site in Iran. The National Renewable Energy Laboratory’s Hybrid Optimization Model for Electric Renewables simulation software has been used to carry out the optimal design and techno-economic viability of the energy system. The simulation results demonstrate that energy system is composed of 10-kW PV array, 3.5-kW electrolyzer, 0.4-kW proton exchange membrane fuel cell, 2.5-kW inverter, and 60 batteries (100 Ah and 12 V). The total initial capital cost, net present cost, and cost of electricity produced from this energy system are 193,563 US$, 237,509 US$, and 3.35 US$/kWh, respectively.     

Optimization of metal bio-acid leaching from mobile phone printed circuit boards using natural organic acids and H2O2

Journal of Material Cycles and Waste Management - With increased popularity and technological innovation, more and more electric and electronic equipment wastes (e-wastes) are being generated....     

Preparation and Optimization of Starch/Poly Vinyl Alcohol/ZnO Nanocomposite Films Applicable for Food Packaging

Pollution and destruction of the environment due to the accumulation of non-degradable plastics are some of the most important concerns in the world. A significant amount of this waste is related to the polymers used in food packaging. Therefore, experts in the food industry have been looking for suitable biodegradable alternatives to synthetic polymers. Preparing biocompatible and biodegradable films based on starch is a good choice. In this study, various factors affecting films of starch/polyvinyl alcohol (PVA)/containing ZnO nanoparticles such as the amount of starch, PVA, glycerol, and ZnO were evaluated by response surface methodology (RSM). Film formation by solvent casting method, mechanical properties, swelling, solubility, and water vapor permeability (WVP) were selected as responses of RSM. The results showed that hydrogen bonding interactions between polyvinyl alcohol and starch improved the film formation. The effect of glycerol and PVA content on the mechanical strength was contrary to each other. As the amount of PVA increased, the tensile strength first decreased and then increased. The value of WVP was for all Runs from 0 to 6.77?×?10^??8 g m^??1 s^??1 Pa^??1. Finally, films with high film formation, maximum tensile strength, and high elongation at break, minimum solubility, permeability, and swelling were optimized.

     

Design and optimization of new La1−xCexNi1−yFeyO3 (x,y = 0–0.4) nano catalysts in dry reforming of methane

The paper reports the production of syngas from dry reforming of methane (DRM) over La_1?xCe_xNi_1?yFe_yO₃ (x, y = 0–0.4) perovskites. A series of La_1?xCe_xNi_1?yFe_yO₃ were designed by central composite design (CCD) and synthesized by a sol–gel auto combustion method. Artificial neural network (ANN) approach was used to determine the relationship between preparation and operational parameters on the performance of the catalysts in the DRM process. Nickel mole fraction, lanthanum mole fraction, calcination temperature, and reaction temperature were considered as input variables, and conversion of methane was considered as the output variable. An ANN model with nine neurons in the hidden layer was the suitable in predicting conversion of methane. The genetic algorithm (GA) was subsequently used to determine the optimal preparation condition for enhancing the conversion of methane. La_0.6Ce_0.4Ni_0.99Fe_0.01O₃ catalyst, calcined at 756°C was obtained to be the most active catalyst owing to the optimal composition of nickel and lanthanum in the catalyst formulation.     

Embedded large eddy simulation approach for pollutant dispersion around a model building in atmospheric boundary layer

In the present article, the potential of embedded large eddy simulation (ELES) approach to reliably predict pollutant dispersion around a model building in atmospheric boundary layer is assessed. The performance of ELES in comparison with large eddy simulation (LES) is evaluated in several ways. These include a number of qualitative and quantitative comparisons of time-averaged and instantaneous results with wind tunnel measurements supplemented by statistical data analyses using scatter plots and standard evaluation metrics. Results obtained by both LES and ELES approaches show very good agreement with the experiment. However, addition of turbulence to mean flow at Reynolds averaged Navier–Stokes (RANS)–LES interface in ELES approach not only increases the turbulence intensity, it also results in larger values of turbulent kinetic energy (TKE) as well as a shorter reattachment length in the wake region. Accordingly, higher levels of TKE predicted by ELES increase the local intensity of concentration leading to shorter plume shapes as compared with LES. In general, ELES shows better agreement with experiment on the surfaces of model building and also in the downstream wake region. In terms of computational costs, the CPU time required to obtain statistical values in ELES is about 49 % lower than that of LES and the number of iterations per time step is also reduced by 55 % as compared with LES.     

Comparative phytotoxicity of ZnO nanoparticles,ZnO microparticles,and Zn2+ on rapeseed (Brassica napus L.): investigating a wide range of concentrations

The effects of ZnO nanoparticles (NPs), ZnO microparticles (MPs), and zinc ions (Zn²⁺) on some growth parameters of rapeseed (Brassica napus) seedlings have been studied. The growth inhibition by ZnO NPs was not stronger than that by ZnO MPs while treatment with Zn²⁺ inhibition was clearly stronger.