A Comparative Study of Environmental Tobacco Smoke Particulate Mass Measurements in an Environmental Chamber

Particulate mass concentration measurements have been made on environmental tobacco smoke (ETS) for the purpose of assessing the relative accuracy of several measurement procedures. ETS over a range of concentrations was generated in an environmental chamber by three methods. Mass concentration was measured by a gravimetric/spectrophotometric collection procedure, piezoelectric particle mass monitors, two nephelometry-based mass monitors, and a particle counting and sizing system. Two-hour average mass concentrations were determined by each method for concentrations ranging from very low levels up to those achieved by smoking one entire cigarette in the chamber. Statistical comparisons were made among procedures employing the gravimetric filter measurement as the basis for comparison. One nephelometry-based procedure gave significantly higher and the other significantly lower values than the filter determination. In one case, a correction for the difference between the particle mass density of the calibrating aerosol and that of ETS brought the nephelometry-based procedure into reasonable agreement with the filter measurement, while for the other, the correction did not resolve the discrepancy between methods. Statistically significant differences between the responses of two supposedly identical piezoelectric mass monitors were found, as was some slight dependence of the nephelometry- based procedures on method of ETS generation. In summary, the results indicate that significant errors can be expected if the instruments studied are used “off the shelf,” even for ETS generated under controlled laboratory conditions. Caution should be employed in field measurements where numerous sources and types of particulate matter can be encountered.     

The Impact of Increased Recycle Rates on Markets in Florida

The State of Florida passed The Florida Solid Waste Management Act of 1988 mandating that county recycling programs be initiated by July 1, 1989. The legislation further expressed the goal that, at a minimum, recycling efforts reduce the amount of solid waste requiring final disposal or resource recovery by 30 percent by the end of 1994. This study was performed to determine the impact on recycle markets when the amounts of materials recycled from the municipal solid waste stream are increased by 30 percent in Florida.

The composition of the municipal waste stream was quantified in terms of the amounts of paper, plastic, metals, glass, and rubber. The effect of a 30 percent increase in the recycle rate of each class of material was calculated and compared to existing recycle rates in the State of Florida. It was determined that there are few capacity constraints on the increase in recycle rates for aluminum, steel (i.e., tin cans), and color separated glass. There are, however, serious constraints on increasing recycle rates for paper, plastics and rubber tires.     

Statistical Assumptions Matter in Data Analysis for Texas Ozone Nonattainment Sites

Strategies for control of ozone aim at regulation of its chemical precursors, non-methane organic compounds (NMOC) and nitrogen oxides (NOx). It is therefore important to analyze how these precursors vary temporally and geographically. This study finds significant and important differences among four Texas ozone nonattainment sites, Dallas, Ft. Worth, El Paso, and Houston, for 1984, 1985, and 1986 for NMOC, NOx, and their ratio NNR. These differences were detected through nonparametric analysis of variance and Student-New-man-Keuls’s test for multiple comparisons on rank-transformed data. A noteworthy feature of the data analysis is its attention to the assumptions underlying the statistical methods. Classical models based on normal or lognormal theory had to be abandoned for lack of realism. It is demonstrated how alternative models may be applied to yield appropriate, rather than inappropriate, conclusions.     

Case Studies of Minimizing Plating Bath Wastes in the Electronics Products Industry

In this paper the authors report on the results of case studies carried out under the sponsorship of the U.S. EPA to determine the effectiveness of four processes designed to reduce the amount of hazardous waste from plating operations. Data reported are based on the results of actual on-site sampling of the processes and encompass effectiveness, environmental, and economic considerations. Two of the case studies evaluating the use of sodium borohydride reduction as a substitute for lime/ferrous sulfate precipitation, found that the technology was a viable substitute in one case and was marginally acceptable in another. Another case study, involving carbon adsorption removal of organic contaminants from plating bath wastes, found that this technology significantly reduced both disposal costs and waste volume. A final case study of electrolytic recovery indicated that while acid copper electroplating rinses are amenable to electrolytic recovery, other metal-bearing rinses, such as those from solder (tin/lead) plating or etching are less appropriate.     

Effect of Relative Humidity on Electrically Stimulated Filter Performance

This work investigates the effect of relative humidity (RH) on the performance of three electrically stimulated filter designs, with and without prechargers. Two different filter media were used: cellulose paper (relatively conductive) and fiberglass paper (relatively nonconductive). Designs with electrodes contacting either of the two filter media are shown to draw currents, exponentially increasing with RH. In contrast, a noncontacting, air gap, electrode design has been shown to be significantly less sensitive to RH. Further, the air gap or noncontacting electrode behaves differently than insulated electrodes. The noncontacting electrode does not exhibit the polarizing or field cancelling effect of insulated (coated) electrodes. This is probably due to a small but finite amount of ionization at the sharp electrode perforations.     

The Effects of Repairs on Tailpipe Emissions for On-Board Diagnostics II-Equipped Vehicles with the Malfunction Indicator Light Illuminated

Abstract

A total of 77 On-Board Diagnostics II (OBDII)-equipped vehicles with illuminated malfunction indicator lights (MILs) and non-evaporative codes were tested before and after repair. The test cycles included the Federal Test Procedure (FTP), IM240, and steady-state cycles. A total of 17 vehicles were found with emissions greater than 1.5 times their respective FTP emissions standards. Repair of these vehicles resulted in dramatic reductions in overall emissions for all the cycles. A majority of the remaining vehicles were found to have emissions below the certification standard for the FTP both before and after repair. Repairs for the vehicles with emissions <1.5 times the standard resulted in some smaller but quantifiable emission reductions over the FTP and IM240 but larger reductions over the steady-state driving tests. Misfires, bad oxygen sensors, and exhaust gas recirculation (EGR) problems were the most common non-evaporative causes for triggering the MIL. The results show some fundamental differences between identifying malfunctioning vehicles using OBDII as opposed to more traditional dynamometer tests. In particular, for many systems, OBDII identifies components that are operating outside their design specification rather than for a specific emissions threshold.     

Investigation of Selective Catalytic Reduction Impact on Mercury Speciation under Simulated NOx Emission Control Conditions

Abstract

Selective catalytic reduction (SCR) technology increasingly is being applied for controlling emissions of nitrogen oxides (NO_x) from coal-fired boilers. Some recent field and pilot studies suggest that the operation of SCR could affect the chemical form of mercury (Hg) in coal combustion flue gases. The speciation of Hg is an important factor influencing the control and environmental fate of Hg emissions from coal combustion. The vanadium and titanium oxides, used commonly in the vanadia-titania SCR catalyst for catalytic NO_x reduction, promote the formation of oxidized mercury (Hg²⁺).

The work reported in this paper focuses on the impact of SCR on elemental mercury (Hg⁰) oxidation. Bench-scale experiments were conducted to investigate Hg⁰ oxidation in the presence of simulated coal combustion flue gases and under SCR reaction conditions. Flue gas mixtures with different concentrations of hydrogen chloride (HCl) and sulfur dioxide (SO₂) for simulating the combustion of bituminous coals and subbituminous coals were tested in these experiments. The effects of HCl and SO₂ in the flue gases on Hg⁰ oxidation under SCR reaction conditions were studied. It was observed that HCl is the most critical flue gas component that causes conversion of Hg⁰ to Hg²⁺ under SCR reaction conditions. The importance of HCl for Hg⁰ oxidation found in the present study provides the scientific basis for the apparent coal-type dependence observed for Hg⁰ oxidation occurring across the SCR reactors in the field.     

Air Quality Modeling and Decisions for Ozone Reduction Strategies

Abstract

Despite the widespread application of photochemical air quality models (AQMs) in U.S. state implementation planning (SIP) for attainment of the ambient ozone standard, documentation for the reliability of projections has remained highly subjective. An “idealized” evaluation framework is proposed that provides a means for assessing reliability. Applied to 18 cases of regulatory modeling in the early 1990s in North America, a comparative review of these applications is reported. The intercomparisons suggest that more than two thirds of these AQM applications suffered from having inadequate air quality and meteorological databases. Emissions representations often were unreliable; uncertainties were too high. More than two thirds of the performance evaluation efforts were judged to be substandard compared with idealized goals. Meteorological conditions chosen according regulatory guidelines were limited to one or two cases and tended to be similar, thus limiting the extent to which public policy makers could be confident that the emission controls adopted would yield attainment for a broad range of adverse atmospheric conditions. More than half of the studies reviewed did not give sufficient attention to addressing the potential for compensating errors. Corroborative analyses were conducted in only one of the 18 studies reviewed. Insufficient attention was given to the estimation of model and/or input database errors, uncertainties, or variability in all of the cases examined. However, recent SIP and policy‐related regional modeling provides evidence of substantial improvements in the underlying science and available modeling systems used for regulatory decision making. Nevertheless, the availability of suitable databases to support increasingly sophisticated modeling continues to be a concern for many locations. Thus, AQM results may still be subject to significant uncertainties. The evaluative process used here provides a framework for modelers and public policy makers to assess the adequacy of contemporary and future modeling work.