Application of gaseous ozone for inactivation of Bacillus subtilis spores

The effectiveness of gaseous ozone (O3) as a disinfectant was tested on Bacillus subtilis spores, which share the same physiological characteristics as Bacillus anthracis spores that cause the anthrax disease. Spores dried on surfaces of different carrier material were exposed to O3 gas in the range of 500-5000 ppm and at relative humidity (RH) of 70-95%. Gaseous O3 was found to be very effective against the B. subtilis spores, and at O3 concentrations as low as 3 mg/L (1500 ppm), approximately 3-log inactivation was obtained within 4 hr of exposure. The inactivation curves consisted of a short lag phase followed by an exponential decrease in the number of surviving spores. Prehydration of the bacterial spores has eliminated the initial lag phase. The inactivation rate increased with increasing O3 concentration but not >3 mg/L. The inactivation rate also increased with increase in RH. Different survival curves were obtained for various surfaces used to carry spores. Inactivation rates of spores on glass, a vinyl floor tile, and office paper were nearly the same. Whereas cut pile carpet and hardwood flooring surfaces resulted in much lower inactivation rates, another type of carpet (loop pile) showed significant enhancement in the inactivation of the spores.     

Phosphate uptake and release rates with different carbon sources in biological nutrient removal using a SBR

A three-step sequencing batch reactor (SBR) was used for nutrient removal from synthetic wastewater with different glucose-organic acid mixtures (1/1). Acetic, butyric, propionic and citric acids were used as organic acids along with glucose. The operation consisted of anaerobic, anoxic and oxic (An/Ax/Ox) phases with durations of 2/1/4.5h. Sludge age was kept constant for 10 days. Phosphate release and uptake rates were determined for different glucose-organic acid mixtures in the feed wastewater. Maximum phosphate uptake (8.1mgPl(-1)h(-1)) and release rates (2.23mgPl(-1)h(-1)) were obtained with the glucose-citric acid mixture. The highest (96%) percent phosphate removal at the end of the nutrient removal cycle (7.5h) was also obtained with the glucose-citric acid mixture while the glucose-acetic acid mixture resulted in comparable percent phosphate removal (95%).     

The impact of pretreatment and inoculum to substrate ratio on methane potential of organic wastes from various origins

Biochemical methane potentials (BMP) of two different substrates from macroalgae (MA) and market place wastes (MPW) were investigated using anaerobic granulated sludge from food industry with different ratios of substrate to inoculum (S/X). The substrates were used as MA only, MPW only, MA–MPW mixture, pretreated MA, and pretreated MA–MPW mixture. Research involved investigation of the effects of parameters such as temperature (35, 45, and 55 °C), substrate to inoculum ratio (S/X = 0.5, 2.0, 4.0, and 6.0 as g VS_substrate/g VS_inoculum), and the type of pretreatment (by microwave, thermal, and ultrasonic) on BMP. BMP assays were performed for all substrates. The highest cumulative biogas production (and BMP) were obtained for MA only at an S/X ratio of 4.0 g VS/g VS as 357 L_biogas/kg VS (197 L CH₄/kg VS) and 33 L_biogas/kg VS (17 L CH₄/kg VS), respectively, at 35 and 55 °C. For pretreated substrates, the highest cumulative biogas production and BMP were observed as 287 L_biogas/kg VS and 146 L CH₄/kg VS using pretreated macroalgae at 35 °C. Results suggested that MA only and MA–MPW mixtures are suitable substrates for biogas production. It is also concluded that any type of pretreatment has adverse effects on biogas and methane productions.     

Mapping of bioclimatic comfort for potential planning using GIS in Aydin

People are relaxed (satisfied or well-off) in what is described as comfortable climatic conditions. In such conditions, a person’s energy balance is not disturbed because of stresses from extreme heat or cold. Bioclimatic structure has been well researched and should be a consideration in the planning process for arranging comfortable spaces. It represents the understanding that energy balance is one of the basic elements of a sustainable landscape design. The goals of this study have been to create ideal places for human thermal comfort and to advance objectives focused on the importance of sustainable and ecological landscape planning and design work, along with their accompanying economic benefits. In this study, which focuses on the climate of the Province of Aydin, the most suitable areas for bioclimatic comfort have been identified. The climate values for the Aydin Province have been taken from a total of 22 meteorological stations. Stations at altitudes ranging from 11 to 871 m were used to note the climate changes that occurred. The average temperature, relative humidity, and wind speed from each station, including data collected using Geographic Information System (GIS) software, were transferred. GIS maps were then created from the imported data, and areas of optimal comfort around the city of Aydin were determined. The results show the range that is suitable for a bioclimatic comfort zone in Aydin. The bioclimatic comfort range was determined to be roughly 17 °C for Aydin, and the city of Aydin demonstrated a comfort range between 14 and 19 °C. As a result, the city of Aydin was shown to be a suitable area for bioclimatic comfort.     

Global solar radiation and energy yield estimation from photovoltaic power plants for small loads

Daily global solar radiation on a horizontal surface and duration of sunshine hours have been determined experimentally for five meteorological stations in Saudi Arabia, namely, Abha, Al-Ahsa, Al-Jouf, Al-Qaisumah, and Wadi Al-Dawaser sites. Five-years of data covering 1998–2002 period have been used. Suitable Angstrom models have been developed for the global solar radiation estimation as a function of the sunshine duration for each respective sites. Daily averages of monthly solar PV power outputs have been determined using the Angstrom models developed. The effect of the PV cell temperature on the PV efficiency has been considered in calculating the PV power output. The annual average PV output energy has been discussed in all five sites for small loads. The minimum and maximum monthly average values of the daily global solar radiation are found to be 12.09 MJ/m²/d and 30.42 MJ/m²/d for Al-Qaisumah and Al-Jouf in the months of December June, respectively. Minimum monthly average sunshine hours of 5.89 hr were observed in Al-Qaisumah in December while a maximum of 12.92 hr in Al-Jouf in the month of June. Shortest range of sunshine hours of 7.33–10.12 hr was recorded at Abha station. Minimum monthly average Solar PV power of 1.59 MJ/m²/day was obtained at Al-Qaisumah in the month of December and a maximum of 3.39 MJ/m²/day at Al-Jouf in June. The annual PV energy output was found to be 276.04 kWh/m², 257.36 kWh/m², 256.75 kWh/m², 245.44 kWh/m², and 270.95 kWh/m² at Abha, Al-Ahsa, Al-Jouf, Al-Qaisumah, and Wadi Al-Dawaser stations, respectively. It is found that the Abha site yields the highest solar PV energy among the five sites considered.     

Energy and exergy analysis of a heat storage tank with a novel eutectic phase change material layer of a solar heater system

Solar energy is one of the most important renewable energy sources, but it is not available every time and every season. Thus, storing of solar energy is important. One of the popular methods of heat storage is use of phase change materials (PCMs) which have large thermal energy storage capacity. In this study, the heat storage tank in a domestic solar water heating system was chosen as control volume. The experiments were performed in the province of Elaz?g, Turkey, in November when solar radiation was weak due to cloudy sky. The heat storage tank of the system was modified to fill PCM between insulation and hot water part. A few PCMs which are Potassium Fluoride, Lithium Metaborate Dihydrate, Strontium Hydroxide Octahydrate, Barium Hydroxide Octahydrate, Aluminum Ammonium Sulfate, and Sodium Hydrogen Phosphate were analyzed to proper operating conditions using a Differential Scanning Calorimeter (DSC) and the best PCM was obtained with the Aluminum Ammonium Sulfate and Sodium Hydrogen Phosphate mixture. Thus, eutectic PCM was obtained and used in a heat storage tank of the solar water heating system. Energy and exergy analysis of heat storage tank was performed with and without the PCM. Energy and exergy analysis has shown that the heat storage tank with the PCM is more efficient than without the PCM and the maximum exergy efficiency was obtained as 22% with the heat storage tank with the PCM.     

The effects of external costs on the system selection for treatment and disposal of municipal solid wastes: a deterministic case study for a pre-assessment

Journal of Material Cycles and Waste Management - Selecting a system for treatment and disposal of municipal solid wastes (i.e., selection of the capacity, location and type of the processes and...     

Green growth and OECD countries: measurement of country performances through distance-based analysis (DBA)

When we measure countries’ socioeconomic development, the standalone National Income approach does not to reflect well-being of the citizens. An analysis of a country's welfare should consider the combination of different aspects such as economic indicators, environmental and resource productivity, and economic opportunities. In the light of these discussions, the concept of green growth arose as a contemporary approach to reframe the mainstream growth model and to re-evaluate many of the investment decisions in meeting agricultural, energy and water needs and the resource demands of economic development. This paper evaluates the green growth performance of OECD countries by applying the I-distance method by integrating the economic, social, and environmental aspects of countries’ performances simultaneously. Using multivariate I-distance approach, selected green growth indicators and numerous different variables have been synthesized into one value. According to our analysis, Sweden, Luxemburg, Norway and Denmark occupy the top places by their outstanding green performance. On the other hand, Mexico, Poland and Greece are placed at the bottom as a consequence of their relatively weak environmental performance.