Acceleration of the Fe(III)EDTA(-) reduction rate in BioDeNO(x) reactors by dosing electron mediating compounds

BioDeNO(x), a novel technique to remove NO(x) from industrial flue gases, is based on absorption of gaseous nitric oxide into an aqueous Fe(II)EDTA(2-) solution, followed by the biological reduction of Fe(II)EDTA(2-) complexed NO to N(2). Besides NO reduction, high rate biological Fe(III)EDTA(-) reduction is a crucial factor for a succesful application of the BioDeNO(x) technology, as it determines the Fe(II)EDTA(2-) concentration in the scrubber liquor and thus the efficiency of NO removal from the gas phase. This paper investigates the mechanism and kinetics of biological Fe(III)EDTA(-) reduction by unadapted anaerobic methanogenic sludge and BioDeNO(x) reactor mixed liquor. The influence of different electron donors, electron mediating compounds and CaSO(3) on the Fe(III)EDTA(-) reduction rate was determined in batch experiments (21mM Fe(III)EDTA(-), 55 degrees C, pH 7.2+/-0.2). The Fe(III)EDTA(-) reduction rate depended on the type of electron donor, the highest rate (13.9mMh(-1)) was observed with glucose, followed by ethanol, acetate and hydrogen. Fe(III)EDTA(-) reduction occurred at a relatively slow (4.1mMh(-1)) rate with methanol as the electron donor. Small amounts (0.5mM) of sulfide, cysteine or elemental sulfur accelerated the Fe(III)EDTA(-) reduction. The amount of iron reduced significantly exceeded the amount that can be formed by the chemical reaction of sulfide with Fe(III)EDTA(-), suggesting that the Fe(III)EDTA(-) reduction was accelerated via an auto-catalytic process with an unidentified electron mediating compound, presumably polysulfides, formed out of the sulfur additives. Using ethanol as electron donor, the specific Fe(III)EDTA(-) reduction rate was linearly related to the amount of sulfide supplied. CaSO(3) (0.5-100mM) inhibited Fe(III)EDTA(-) reduction, probably because SO(3)(2-) scavenged the electron mediating compound.     

Enrichment of the metallic components from waste printed circuit boards by a mechanical separation process using a stamp mill

Printed circuit boards incorporated in most electrical and electronic equipment contain valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, and Pb. In order to employ a hydrometallurgical route for the recycling of valuable metals from printed circuit boards, a mechanical pre-treatment step is needed. In this study, the metallic components from waste printed circuit boards have been enriched using a mechanical separation process. Waste printed circuit boards shredded to <10mm were milled using a stamp mill to liberate the various metallic components, and then the milled printed circuit boards were classified into fractions of <0.6, 0.6-1.2, 1.2-2.5, 2.5-5.0, and >5.0mm. The fractions of milled printed circuit boards of size <5.0mm were separated into a light fraction of mostly non-metallic components and a heavy fraction of the metallic components by gravity separation using a zig-zag classifier. The >5.0mm fraction and the heavy fraction were subjected to two-step magnetic separation. Through the first magnetic separation at 700 Gauss, 83% of the nickel and iron, based on the whole printed circuit boards, was recovered in the magnetic fraction, and 92% of the copper was recovered in the non-magnetic fraction. The cumulative recovery of nickel-iron concentrate was increased by a second magnetic separation at 3000 Gauss, but the grade of the concentrate decreased remarkably from 76% to 56%. The cumulative recovery of copper concentrate decreased, but the grade increased slightly from 71.6% to 75.4%. This study has demonstrated the feasibility of the mechanical separation process consisting of milling/size classification/gravity separation/two-step magnetic separation for enriching metallic components such as Cu, Ni, Al, and Fe from waste printed circuit boards.     

Degradation of lignocellulosic materials under sulfidogenic and methanogenic conditions

Biochemical methane potential (BMP) assays, typically used to assess anaerobic biodegradability of liquid wastes with added nutrients and bacteria, were adapted to compare hydrolysis of lignocellulosic material under sulfidogenic and methanogenic environments. A method based on selective inhibition of microorganism activity, by 3% toluene, was used to measure the hydrolysis rate of lignocellulosic material and the accumulation of sugar. The neutral sugars, galactose, glucose, and xylose, which were released from lignocellulosic material such as office paper and newspaper in the presence 3% toluene, clearly accumulated over time under sulfidogenic conditions. The accumulation rates of sugars, glucose, and xylose, were higher in the sulfidogenic condition than in the methanogenic condition, indicating a faster degradation of lignocellulosic materials under the sulfidogenic condition.     

LEHR superfund stormwater runoff and putah creek mercury issues

Stormwater runoff from the University of California, Davis/U.S. Department of Energy Laboratory for Energy‐Related Health Research (UCD/US DOE LEHR) Superfund site located on the University of California campus in Davis, California, has been found to contain over 500 ng/L of total recoverable mercury, which is about ten times the California Toxics Rule criterion. This stormwater runoff is discharged to Putah Creek, which is Clean Water Act Section 303(d) listed as impaired for excessive mercury bioaccumulation in edible fish. A discussion is presented on the potential impact of the mercury in stormwater runoff from LEHR leading to excessive bioaccumulation of mercury in Putah Creek fish. The mercury in the stormwater runoff is derived from former flooding of the soils near the creek, which contains mercury derived from abandoned upstream mercury mines located in the Coast Range Vaca Hills to the west of LEHR. The implications of this situation for implementing a Total Maximum Daily Load (TMDL) to control mercury in stormwater runoff to Putah Creek are presented. © 2009 Wiley Periodicals, Inc.     

Older driver retraining: An updated systematic review of evidence of effectiveness

Problem and Objective

The number of older drivers who might benefit from driver retraining is growing. A previous review on the effectiveness of older driver retraining included intervention studies up to 2004. The objective was to perform an updated systematic review of the effectiveness of older driver retraining for improving driving-related skills and reducing crash rates.

Method

Articles published from 2004-2008 were grouped according to the intervention provided and outcome studied. Randomized clinical trials (RCTs) were appraised using the Physiotherapy Evidence Database (PEDro) Scale and scored for quality according to their internal validity. Each intervention's effectiveness was then rated and assigned a level of evidence by combining pre- and post- 2004 findings.

Results

Three RCTs and one matched-pairs cohort design met the inclusion criteria. There is strong evidence (Level 1a) that education combined with on-road training improves driving performance and moderate evidence (Level 1b) that it improves knowledge. There is moderate evidence (Level 1b) that physical retraining improves driving performance. There is moderate evidence (Level 1b) that an educational intervention curriculum alone is not effective in reducing crashes.

Summary

The updated evidence on the effectiveness of retraining aimed at older drivers is sufficiently encouraging to merit assertive health promotion actions regarding intervention and program planning.

Impact on Industry

These positive findings warrant a comprehensive plan that has both behavioral and monetary incentives encouraging older driver participation in programs aimed at driver safety.     

The characteristics of fatal occupational injuries in Korea’s construction industry, 1997–2004

This study is aimed at exploring the characteristics of fatal occupational injuries in Korea’s construction industry and comparing the causes in various occupations within that industry. There were 10,276 fatal occupational injury victims in Korea over 8 years (1997–2004). The mortality risk due to injuries in construction and non-construction industries was calculated, and their causes were compared. The number of victims of fatal occupational injuries in the construction industry was 4333 (42.2% of the total fatal occupational injuries), and the 1 year mortality risk was higher (23.7/100,000 persons) than in non-construction industries (10.4). Falling was the most frequent (52.7%) cause of fatal injuries. In addition, deaths due to structural collapse and electric shock were significantly higher than in other industries. When the distribution of the causal factors in various occupations within the construction industry was investigated, some factors appeared more frequently in certain occupations than in others. As the construction industry encompasses a large proportion of occupational injuries, a reduction in this field alone will substantially contribute to an overall reduction of occupational injuries in Korea. Further research for effective prevention is needed.     

Focus on mission success: Process safety for the Atychiphobist

Modern process plants are complex engineering systems. While thorough reviews of system safeguards are performed, catastrophic events continue to occur, often unfolding in unforeseen ways. Success in process safety demands safe processes, and understanding rare, high consequence events is central to the traditional process safety approach. This philosophy is common to all high-hazard industries, offering the potential for sharing approaches, experience, and lessons learned. The problem, however, is that people (and organizations and entire industries) who fear failure (atychiphobia) sometimes obsess about failure so much that they miss opportunities to succeed.This paper examines selected risk management practices in the power generation and aerospace industries and how those practices have led to improved performance. Risk informed decision making (RIDM) has had widespread application in the nuclear and aerospace industries, and is undergoing enhancements to become a key framework for risk management. Additionally, rather than focusing on avoidance of loss, there are emerging approaches supporting achievement of success. This approach provides a more direct link of risk to business and operational objectives, but does challenge conventional risk approaches founded in a loss prevention-centric view. The paper reflects upon risk informed decision making and success modeling, and suggests how these methods may be applied in the field of process safety. Specific examples are drawn from the defense in depth approach from the nuclear power industry and mission success concepts developed for NASA.     

Modelling the contribution of different sources of sulphur to atmospheric deposition in the United Kingdom

In order to understand relationships between sources and receptors of atmospheric deposition, computer models must be used. This paper describes a Lagrangian acid deposition model that represents emissions of trace species across Northern Europe. The chemistry of sulphur dioxide, dimethyl sulphide and hydrogen sulphide is represented and the model tested against estimates of UK wet and dry deposition. Mean UK wet and dry deposition for the period 1992–1994 was 206 and 145 ktonne S yr^-1, respectively. The model predicted wet and dry deposition of 222 and 166 ktonne S yr^-1, in good agreement with measurements. The model has been used to examine the sources of deposited S to the UK. For a base year of 1992, 86% of the UK's SO₂ emissions are exported. The S deposition attributable from mainland European sources was 36% of the UK total S deposition, in good agreement with other UK models but this differs substantially from the calculations of the EMEP model. Natural sources of S deposition from planktonic emissions of dimethyl sulphide, biological emissions of hydrogen sulphide and non-eruptive volcanic emissions of sulphur dioxide contributed approximately 1% of the modelled UK S deposition, of which 95% originated from dimethyl sulphide. The explicit chemical scheme for dimethyl sulphide incorporated into the model showed that 24% of the resultant deposited S was methane sulphonic acid. Boundary conditions of the model were tested and it was found that initialisation of sulphur dioxide and sulphate concentrations to representative ambient conditions had a very small effect. The modelled contribution of UK and European sources to UK S deposition was approximately 40 and 60%, respectively, showing the dramatic change arising from projected UK SO₂ emissions in 2010. This revised version was published online in July 2006 with corrections to the Cover Date.     

Land Use Changes in Regional Economic Theory

Land use and land cover changes are a major source of environmental degradation and therefore a serious issue in sustainable development studies and in the integrated assessment of environmental problems. In an attempt to understand part of the complexity of land use change we here aim to explore the ways in which economists deals with the land use issue. We argue that space is one of the forgotten items in economics. Economists often seem to ignore high-resolution spatial dynamics either because they are not considered as an important feature of the problem or out of habit. It seems as though there is a trade-off between spatial resolution and human behaviour in current applications. Certain types of models are capable of capturing the spatial complexity of urban and regional areas, for instance, by using cellular automata. Other types of land use models clearly have shortcomings where it concerns spatial detail. Dynamic modelling approaches do not guarantee a high spatial resolution.We propose to give more attention to agent based modelling as this type of modelling provides a specific connection between processes on micro level and macro-level spatial structures.