海洋柴油溢油油水快速分离的应用研究

针对海洋柴油溢油,采用破乳剂对油水快速分离进行了研究.分别对油水比、温度、破乳剂量及存在Ca2 、Mg2 的影响因素,进行了系列油水快速分离试验,并测定了破乳剂作用下乳液的界面张力.试验结果表明,柴油溢油形成的乳液稳定性较差,油水分离较容易,但分离后的水中含油量较高.加入聚醚类非离子型破乳剂FA、FB、FC和FD,可达到油水低温、快速分离的目的,且分离后的水中含油量较低.随着破乳剂浓度的增加,界面张力降低,当破乳剂浓度达到临界胶束浓度(CMC)时,界面张力最小,脱水效果最好.Ca2 、Mg2 对聚醚类非离子型破乳剂的影响很小.     

啤酒生产废水处理设计及运行研究

分析了年产15万t啤酒的生产废水情况,介绍了采用IC厌氧反应器-一体化氧化沟处理该生产废水(7 200 m3/d)的工艺路线和主要设计参数,讨论了废水处理系统的运行情况.其中IC厌氧反应器的HRT为8 h,运行温度为35～37 ℃;一体化氧化沟包括氧化沟段和沉淀池段,总尺寸为40 m×24 m×6 m.IC厌氧反应器COD容积负荷在7.78 kg/(m3·d)时,COD去除率为84%左右.整套废水处理系统的COD总去除率为98%左右,出水COD小于80 mg/L.厌氧所产生的沼气可用于废水的升温.     

秸秆成型燃料锅炉污染物排放规律试验研究

根据锅炉烟尘测试方法(GB 5468-91)及锅炉大气污染物排放标准(GB 13271-2001),在不同风门的工况下,分别对设计的双层炉排秸秆成型燃料锅炉污染物排放规律进行试验.试验表明,在较好工况下,双层炉排锅炉排烟中CO等中间产物及烟尘含量低于单层炉排锅炉,其排烟中CO、NOx、SO2和烟尘浓度等指标远远低于燃煤锅炉,符合国家关于工业锅炉大气污染物排放标准要求,有较好环保效益.     

Radiocarbon content of synthetic and natural semi-volatile halogenated organic compounds

Some halogenated organic compounds, such as polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins (PCDDs) and polybrominated diphenyl ethers (PBDEs), have been suggested to have natural sources but separating these compounds from their commercially synthesized counterparts is difficult. Molecular-level 14C analysis may be beneficial since most synthetic compounds are manufactured from petrochemicals (14C-free) and natural compounds should have "modern" or "contemporary" 14C levels. As a baseline study, we measured, for the first time, the 14C abundance in commercial PCB and PBDE mixtures, a number of organochlorine pesticides, as well as one natural product 2-(3',5'-dibromo-2'-methoxyphenoxy)-3,5-dibromoanisole. The latter compound was isolated from a marine sponge and is similar in structure to a PBDE. All of the synthetic compounds were 14C-free except for the pesticide toxaphene. which had a modern 14C abundance, as did the brominated natural compound. The result for toxaphene was not surprising since it was commercially synthesized by the chlorination of camphene derived from pine trees. These results suggest that measuring the 14C content of halogenated organic compounds may be quite useful in establishing whether organic compounds encountered in the environment have natural or synthetic origins (or both) provided that any synthetic counterparts derive from petrochemical feedstock.     

Mechanism of PCBs formation from the pyrolysis of chlorobenzenes

Polychlorinated biphenyls (PCBs) were formed by pyrolysis of chlorobenzenes in a HCl atmosphere. Varieties of substituted chlorobenzenes were used as model compounds to optimize the condensation reaction. Lower chlorinated benzenes produce more PCBs than that of higher ones. Up to 0.7 microg PCBs/mg 1,2,3-trichlorobenzene was produced through the condensation reaction.     

Comparative studies of the Fe–UV, H2O2–UV, TiO2–UV/vis systems for the decolorization of a textile dye X-3B in water

The degradation of a common textile dye, Reactive-brilliant red X-3B, by several advanced oxidation technologies was studied in an air-saturated aqueous solution. The dye was resistant to the UV illumination (wavelength λ  320 nm), but was decolorized when one of Fe³⁺, H₂O₂ and TiO₂ components was present. The decolorization rate was observed to be quite different for each system, and the relative order evaluated under comparable conditions followed the order of Fe²⁺–H₂O₂–UV  Fe²⁺–H₂O₂ > Fe³⁺–H₂O₂–UV > Fe³⁺–H₂O₂ > Fe³⁺–TiO₂–UV > TiO₂–UV > Fe³⁺–UV > TiO₂–visible light (λ  450 nm) > H₂O₂–UV > Fe²⁺–UV. The mechanism for each process is discussed, and linked together for understanding the observed differences in reactivity.     

污水在水体中的稀释扩散及稀释度的计算

结合长江白龙港水域水力模型试验对污水排海工程中污水稀释扩散的机理进行了描述，并对污水的两种稀释度（浓度释稀度和体积稀释度）进行了分析比较，得出了在污染物本底值存在时两种稀释度之间的关系。     

生物质型煤成型技术开发实验研究

通过原有成型方式的工业成型观察和模压成型实验，提出并验证了完全利用生物质纤维的交联作用实现成型的新机制。其于中高压下物料的不可再压缩性和单向挤压也会导致更高的成型压力的新认识，设计和研制成按新机制成型的型轮。经此改进的工业成型试验达到了比模压成型更好的效果：不用预实送料，且成型性能；成型压力降至120MPa以下，成型许可水分成倍提高，适合的生物质配比范围15％－60％；仅利用送料螺旋的预实功能，即可实现纯生物质型块的成型。     

染料废水脱色混凝剂(PSDC-Ⅰ) 的制备和效果实验

研究了由固体废物 (炼铁废渣 )制取的含有多种金属离子的染料废水脱色混凝剂 (PSDC Ⅰ ) ,试验了它对染料废水的脱色效果及对印染废水的混凝效果 ,并与PAC进行了比较。考察了影响PSDC Ⅰ混凝及脱色效果的因素。结果表明 ,pH值在 6— 10范围内 ,PSDC Ⅰ具有良好的混凝效果。PSDC Ⅰ的两个最佳脱色区为 pH值 6— 8和 pH值 13左右。与PAC相比 ,PSDC Ⅰ不仅具有良好的混凝效果而且具有良好的脱色效果     

The styrene purification performance of biotrickling filter with toluene-styrene acclimatization under acidic conditions

The obvious disadvantages of biotrickling filters (BTFs) are the long start-up time and low removal efficiency (RE) when treating refractory hydrophobic volatile organic compounds (VOCs), which limits its industrial application. It is worthwhile to investigate how to reduce the start-up period of the BTF for treating hydrophobic VOCs. Here, we present the first study to evaluate the strategy of toluene induction combined with toluene-styrene synchronous acclimatization during start-up in a laboratory-scale BTF inoculated with activated sludge for styrene removal, as well as the effects of styrene inlet concentration (0.279 to 2.659 g·m^?3), empty bed residence time (EBRT) (i.e., 136, 90, 68, 45, 34 sec), humidity (7.7% to 88.9%), and pH (i.e., 4, 3, 2.5, 2) on the performance of the BTF system. The experiments were carried out under acidic conditions (pH 4.5) to make fungi dominant in the BTF. The start-up period for styrene in the BTF was shortened to about 28 days. A maximum elimination capacity (EC_max) of 126 g·m^?3·hr^?1 with an RE of 80% was attained when styrene inlet loading rate (ILR) was below 180 g·m^?3·hr^?1. The highest styrene RE(s) [of BTF] that could be achieved were 95% and 93.4%, respectively, for humidity of 7.7% and at pH 2. A single dominant fungal strain was isolated and identified as Candida palmioleophila strain MA-M11 based on the 26S ribosomal RNA gene. Overall, the styrene induction with the toluene-styrene synchronous acclimatization could markedly reduce the start-up period and enhance the RE of styrene. The BTF dominated by fungi exhibited good performance under low pH and humidity and great potential in treating styrene with higher inlet concentrations.

Implications: The application of the toluene induction combined with toluene-styrene synchronous acclimatization demonstrated to be a promising approach for the highly efficient removal of styrene. The toluene induction can accelerate biofilm formation, and the adaptability of microorganisms to styrene can be improved rapidly by the toluene-styrene synchronous acclimatization. The integrated application of two technologies can shorten the start-up period of biotrickling filters markedly and promote its industrial application.