Simultaneous Sampling of Gas- and Aerosol-Phase TDI with a Triple Filter System

Abstract

A new triple filter system sampler/model is proposed for the precise and accurate simultaneous sampling and determination of gas- and aerosol-phase 2,4-toluene diisocyanate (TDI). The system consists of two front Teflon filters for sampling aerosol-phase TDI and a final coated glass fiber filter to collect gas-phase TDI. The aerosol-phase TDI is collected on the first Teflon filter, while the second Teflon filter is used to estimate gaseous TDI adsorbed by the first. According to the gas adsorption test of two Teflon filters in series, the TDI gas adsorption fraction of the two filters is almost the same. Results of the evaporation test using pure TDI aerosols collected on the Teflon filter show that significant evaporation of the compound does not occur during sampling. These two findings allow the use of a model to estimate accurate gasand aerosol-phase TDI concentrations. The comparison test with an annular denuder shows that the triple filter system can minimize the TDI sampling bias between the dual filter and the annular denuder systems.     

Properties of Pyrolytic Chars and Activated Carbons Derived from Pilot-Scale Pyrolysis of Used Tires

Abstract

Used tires were pyrolyzed in a pilot-scale quasi-inert rotary kiln. Influences of variables, such as time, temperature, and agent flow, on the activation of obtained char were subsequently investigated in a laboratory-scale fixed bed. Meso-porous pores are found to be dominant in the pore structures of raw char. Brunauer-Emmett-Teller (BET) surfaces of activated chars increased linearly with carbon burnoff. The carbon burnoff of tire char achieved by carbon dioxide (CO₂) under otherwise identical conditions was on average 75% of that achieved by steam, but their BET surfaces are almost the same. The proper activation greatly improved the aqueous adsorption of raw char, especially for small molecular adsorbates, for example, phenol from 6 to 51 mg/g. With increasing burnoff, phenol adsorption exhibited a first-stage linear increase followed by a rapid drop after 30% burnoff. Similarly, iodine adsorption first increased linearly, but it held as the burnoff exceeded 40%, which implied that the reduction of iodine adsorption due to decreasing micro-pores was partially made up by increasing mesopores. Both raw chars and activated chars showed appreciable adsorption capacity of methylene-blue comparable with that of commercial carbons. Thus, tire-derived activated carbons can be used as an excellent mesoporous adsorbent for larger molecular species.     

Predicting Cutoff Aerodynamic Diameter and Sharpness of Single Round-Nozzle Impactors with a Finite Impaction Plate Diameter

Abstract

This investigation numerically examined the cutoff aerodynamic diameter (da₅₀) and the sharpness (GSD) of the particle collection efficiency curve of impactors with a finite impaction plate diameter. Results revealed that the inertial impactors have a limited cutoff aerodynamic diameter at different air velocities. The extreme value of the cutoff aerodynamic diameter increases with the nozzle diameter (W)/the plate diameter (D_c). The computed da₅₀/D_c values of the impactors increase with W/D_c at various Reynolds numbers (Re) and with the nozzle-toplate distance (S)/D_c when Re is 100. The value of GSD slightly increases with W/D_c for Re of 10 and 100, although the effect of S/D_c on GSD is not evident at various Res. The particle collection efficiency curve of the impactor with a lower Re is less sharp than that with a high Re at various W/D_c and S/D_c values. Statistical equations closely fitted the obtained numerical results for Res of 10–3000. The equations are useful for directly calculating the cutoff aerodynamic diameter and the sharpness of the particle collection efficiency curve for single round-nozzle impactors with a finite impaction D_c.     

Decomposition of Gas Phase 1,3-Butadiene by Ultraviolet/Ozone Process

Abstract

A pilot-scale plug-flow reactor was built to investigate its performance in treating airborne 1,3-butadiene (BD) via ozonation (O₃) and ultraviolet (UV)/O₃ technologies. Governing factors, such as the initial molar ratio of ozone to BD, UV volumetric electric input power, and moisture content in the influent airstream, were investigated. Experiments were conducted at an influent BD concentration of ～50 ppm, an ambient temperature of 26 °C, and a gas retention time of 85 sec. Results show that an initial molar ratio of ozone to BD of 3.5 and 2 sufficed to obtain BD decompositions of >90% for ozonation and UV/O₃, respectively. The UV irradiance did not directly promote the decomposition of BD, rather, it played a role in promoting the production of secondary oxidants, such as hydroxyl radicals. Kinetic analyses indicate that both types of BD decomposition are peudo–first-order with respect to BD concentrations. Moisture content (relative humidity = 40–99%) and UV volumetric electric input power (0.147 and 0.294 W/L) are both factors that weakly affect the rate of BD decomposition. Economic evaluation factors, including both energy of ozone production and UV electric input power, were also estimated.     

Influence of particle location on the number of charges per charged nanoparticle at the outlet of a needle charger

This study has investigated numerically the influence of particle location on the number of charges per charged particle in the 10–40 nm size range at the outlet of a needle charger by simulating flow field, electric field, particle charging, and particle trajectory at various conditions. The results show that the total (i.e., diffusion + field charging) number of charges per particle increase with decreasing ratio values of radial location at the outlet of the charger due to the particle position close to the needle tip. It has also been shown that in the outlet region of the charger there is a critical radial location at which the number of charges per particle is a maximum; this critical radial location represents the point at which the charged particle trajectory becomes closest to the needle electrode. The maximum value of number of charges increases with increasing Reynolds number and slightly increases with decreasing applied voltage for particle diameter larger than 20 nm. The maximum number of charges per charged nanoparticle increases with increasing particle diameter. In addition, the minimum ratio value of radial particle location decreases with increasing Reynolds number for various particle diameters.

Implications: In this work, the influence of particle location on the number of charges per charged nanoparticle at the outlet of a needle charger has been investigated using numerical models under different conditions. The results demonstrate that the radial location affects the number of charges per particle at the outlet of the charger. The maximum number of charges increases with increasing particle diameter, and the minimum ratio value of radial particle location decreases with increasing Reynolds number. The numerical models explain and quantify the number of charges on the charged particle in the 10–40 nm size range from the outlet of the needle charger at various conditions.     

A theoretical overview of the relationship between the resource curse and genuine savings as an indicator for “weak” sustainability

This paper shows the strong relation between the factors that lead to the resource curse (RC) and factors that lead to a decline of genuine savings (GS). There is substantial empirical evidence that economies that rely predominantly on their natural resources are also characterized by slower economic growth. This so‐called RC is commonly traced back to the fact that natural resources' generate rents that are independent of a country's economic performance, which can lead to suboptimal reinvestments of this consumed natural capital. We argue that the factors responsible for the RC also have a negative effect on GS, a concept that measures “weak” sustainable development by considering reinvestment of natural capital rents in physical and human capital. We discuss whether the RC hampers possibilities for resource abundant countries to obtain sufficiently high rates of GS, and find indeed many reasons why resource‐dependent countries have problems achieving positive GS rates. We survey both areas of research, emphasizing the influence of the exogenous and endogenous determinants of economic growth, which are usually used to theoretically and empirically explain the RC on the three different forms of capital considered by GS. We specify why most countries suffering from the RC have negative GS rates and explain in detail where the linkages are. This overview could help with potential advancements in the explanation of GS through the inclusion of RC effects.     

变压吸附技术的应用及其发展简述

文章分析了变压吸附技术存在的问题,并提出解决措施。通过对变压吸附技术应用现状的总结,对该技术未来的发展方向进行预测与评价。指出变压吸附技术能够经济高效地实现物质的分离,有望成为分离技术未来的发展方向,为环保和工业生产做出更大贡献。     

回收与降解聚驱采出水的工艺探讨

含聚污水的处理是困扰石油行业的难题之一。基于聚驱采出水的特点,围绕聚合物的回收利用和降解理论及技术,探讨国内外含聚污水处理技术的研究与应用现状,对比分析现有处理技术存在的问题及适应性,提出采用化学混凝、气浮和水质改性等技术来回收利用PAM(聚丙烯酰胺)的新思路,打破了降解PAM的传统思维,同时分析含聚污水处理与利用技术的可行性与应用前景,有望实现含聚污水的循环利用。     

微生物法处理海上钻井废钻井液

微生物法适用于海上钻井含油废弃物的处理。通过多次对菌株采集、分离、纯化和培养驯化,选育得到了3株对石油烃类有很好降解效果的石油类降解菌;确定了石油类降解菌适宜的生化处理条件:最佳生长及原油降解温度为50℃、最佳生长及原油降解酸碱性环境为pH=6.0、最佳菌株接种量2%、最佳原油初始浓度为500mg/L。处理后的含油废弃钻井液含油量基本稳定在2mg/L以下,降解率达98%以上。