A fluorescence-based bioassay for aquatic macrophytes and its suitability for effect analysis of non-photosystem II inhibitors

Background, Goals and Scope During the last years the miniaturization of toxicity test systems for rapid and parallel measurements of large quantities of samples has often been discussed. For unicellular algae as well as for aquatic macrophytes, fluorescence-based miniaturized test systems have been introduced to analyze photosystem II (PSII) inhibitors. Nevertheless, high-throughput screening should also guarantee the effect detection of a broad range of toxicants in order to ensure routinely applicable, high-throughput measuring device experiments which can cover a broad range of toxicants and modes of action others than PSII inhibition. Thus, the aim of this study was to establish a fast and reproducible measuring system for non-PSII inhibitors for aquatic macrophyte species to overcome major limitations for use. Methods A newly developed imaging pulse-amplitude-modulated chlorophyll fluorometer (I-PAM) was applied as an effect detector in short-term bioassays with the aquatic macrophyte species Lemna minor. This multiwell-plate based measuring device enabled the incubation and measurement of up to 24 samples in parallel. The chemicals paraquat-dichloride, alizarine and triclosan were chosen as representatives for the toxicant groups of non-PSII herbicides, polycyclic aromatic hydrocarbons (PAHs) and pharmaceuticals and personal care products (PPCPs), which are often detected in the aquatic environment. The I-PAM was used (i) to establish and validate the sensitivity of the test system to the three non-PSII inhibitors, (ii) to compare the test systems with standardized and established biotests for aquatic macrophytes, and (iii) to define necessary time scales in aquatic macrophyte testing. For validation of the fluorescence-based assay, the standard growth test with L. minor (ISO/DIS 20079) was performed in parallel for each chemical. Results The results revealed that fluorescence-based measurements with the I-PAM allow rapid and parallel analysis of large amounts of aquatic macrophyte samples. The I-PAM enabled the recording of concentration-effect-curves with L. minor samples on a 24-well plate with single measurements. Fluorescence-based concentration-effect-curves could be detected for all three chemicals after only 1 h of incubation. After 4–5 h incubation time, the maximum inhibition of fluorescence showed an 80–100% effect for the chemicals tested. The EC50 after 24 h incubation were estimated to be 0.06 mg/L, 0.84 mg/L and 1.69 mg/L for paraquatdichloride, alizarine and triclosan, respectively. Discussion The results obtained with the I-PAM after 24 h for the herbicide paraquat-dichloride and the polycyclic aromatic hydrocarbon alizarine were in good accordance with median effective concentrations (EC50s) obtained by the standardized growth test for L. minor after 7 d incubation (0.09 mg/L and 0.79 mg/L for paraquat-dichloride and alizarine, respectively). Those results were in accordance with literature findings for the two chemicals. In contrast, fluorescence-based EC50 of the antimicrobial agent triclosan proved to be two orders of magnitude greater when compared to the standard growth test with 7 d incubation time (0.026 mg/L) as well as with literature findings. Conclusion Typically, aquatic macrophyte testing is very time consuming and relies on laborious experimental set-ups. The I-PAM measuring device enabled fast effect screening for the three chemicals tested. While established test systems for aquatic macrophytes need incubation times of ≥ 7 d, the I-PAM can detect inhibitory effects much earlier (24 h), even if inhibition of chemicals is not specifically associated with PSII. Thus, the fluorescence-based bioassay with the I-PAM offers a promising approach for the miniaturization and high-throughput testing of chemicals with aquatic macrophytes. For the chemical triclosan, however, the short-term effect prediction with the I-PAM has been shown to be less sensitive than with long-term bioassays, which might be due to physicochemical substance properties such as lipophilicity. Recommendations and Perspectives The results of this study show that the I-PAM represents a promising tool for decreasing the incubation times of aquatic macrophyte toxicity testing to about 24 h as a supplement to existing test batteries. The applicability of this I-PAM bioassay on emergent and submerged aquatic macrophyte species should be investigated in further studies. Regarding considerations that physicochemical properties of the tested substances might play an important role in microplate bioassays, the I-PAM bioassay should either be accompanied by evaluating physicochemical properties modeled from structural information prior to an experimental investigation, or by intensified chemical analyses to identify and determine nominal concentrations of the toxicants tested. The chemicals paraquat-dichloride, alizarine and triclosan were chosen as representatives for the toxicant groups of non-PSII herbicides, PAHs and PPCPs which are often detected in the aquatic environment. Nevertheless, in order to ensure a routinely applicable measuring device, experiments with a broader range of toxicants and samples of surface and/or waste waters are necessary. ESS-Submission Editor: Dr. Markus Hecker (MHecker@Entrix.com)     

Phosphorus Load Reduction Goals for Feitsui Reservoir Watershed, Taiwan

The present paper describes an effort for developing the total maximum daily load (TMDL) for phosphorus and a load reduction strategy for the Feitsui Reservoir in Northern Taiwan. BASINS model was employed to estimate watershed pollutant loads from nonpoint sources (NPS) in the Feitsui Reservoir watershed. The BASINS model was calibrated using field data collected during a 2-year sampling period and then used to compute watershed pollutant loadings into the Feitsui Reservoir. The simulated results indicate that the average annual total phosphorus (TP) loading into the reservoir is 18,910 kg/year, which consists of non-point source loading of 16,003 kg/year, and point source loading of 2,907 kg/year. The Vollenweider mass balance model was used next to determine the degree of eutrophication under current pollutant loading and the load reduction needed to keep the reservoir from being eutrophic. It was estimated that Feitsui Reservoir can becoming of the oligotrophic state if the average annual TP loading is reduced by 37% or more. The results provide the basis on which an integrated control action plan for both point and nonpoint sources of pollution in the watershed can be developed.     

Survey of heavy metal pollution and assessment of agricultural soil in Yangzhong district, Jiangsu Province, China

We investigated concentrations of Hg, Cd, Pb, Zn, Cu, As, Ni, and Cr in samples of soil, cereal, and vegetables from Yangzhong district, China. Compared to subsoils, the sampled topsoils are enriched in Hg, Cd, Cu, Pb, Zn, and As. High levels of Cd and Hg are observed in most agricultural soils. Concentrations of Cr and Ni show little spatial variation, and high Cu, Pb, and Zn contents correspond well to areas of urban development. High As contents are primarily recorded at the two ends of the sampled alluvion. The contents of Cd, Hg, and total organic carbon (TOC) increase gradually to maximum values in the upper parts of soil profiles, while Cr and Ni occur in low concentrations within sampled profiles. As, Pb, Cu, and Zn show patterns of slight enrichment within the surface layer. Compared to data obtained in 1990, Cd and Hg show increased concentrations in 2005; this is attributed to the long-term use of agrochemicals. Cr and Ni contents remained steady over this interval because they are derived from the weathering of parent material and subsequent pedogenesis. The measured As, Cu, Pb, and Zn contents show slight increases over time due to atmospheric deposition of material sourced from urban anthropogenic activity. Low concentrations of heavy metals are recorded in vegetables and cereals because the subalkaline environment of the soil limits their mobility. Although the heavy metal concentrations measured in this study do not pose a serious health risk, they do affect the quality of agricultural products.     

Suborganismic and organismic effects of aldicarb and its metabolite aldicarb-sulfoxide to the zebrafish embryo (Danio rerio)

The new European chemical regulation (REACH) requires a short-term fish test for chemicals where the level of production exceeds 10tons per year. For ethical reasons (3R-concept), an alternative to the acute fish test should be introduced to decrease the number of animal testing with fish. The zebrafish embryo (Danio rerio) test became a valuable tool in ecotoxicology and already replaces the acute fish test for the evaluation of wastewater in Germany. Recent efforts are targeted to use this and other fish embryo tests for the effect assessment of chemicals. The toxic effects of the carbamate insecticide aldicarb and its metabolite aldicarb-sulfoxide to zebrafish embryos were analysed using two approaches with different endpoints. Organismic tests were conducted with zebrafish embryos exposed to the pesticides for 48h. In addition, suborganismic effects were examined analysing the enzyme inhibition of cholinesterases and carboxylesterases. On the organismic level, the only sublethal effect seen was the increase of heart rate at low and decrease at higher concentration with the use of aldicarb-sulfoxide but not with aldicarb (concentration range 0.2-300microM). In contrast, analysis of enzyme inhibitions showed high to very high effects caused by the two carbamates. The enzyme inhibition analysis of whole homogenates of exposed embryos may be advantageous for toxicant screening (biomarker of exposure) and might be used to bridge the gap of sensitivity of the (48h old) zebrafish embryos to adult fish when exposed to anti-cholinesterase substances (biomarker of prospective effect).     

Removal of dinitrotoluenes from water via reduction with iron and peroxidase-catalyzed oxidative polymerization: a comparison between Arthromyces ramosus peroxidase and soybean peroxidase

A two-step process for the removal of dinitrotoluene from water is presented: zero-valent iron reduction is coupled with peroxidase-catalyzed polymerization of the resulting diaminotoluenes (DAT). The effect of pH was examined in the reduction step: at pH 6 the reaction occurred much more rapidly than at pH 8. In the second step, optimal pH and substrate ratio, minimal enzyme concentration and effect of polyethylene glycol (PEG) as an additive for greater than 95% conversion of DAT, over a 3h reaction period were determined using high performance liquid chromatography. Two enzymes were investigated and compared: Arthromyces ramosus peroxidase (ARP) and soybean peroxidase (SBP). The optimal pH values were 5.4 and 5.2 for ARP and SBP, respectively, but SBP was more resistant to mild acid whereas ARP was more stable in neutral solutions. SBP was found to have a greater hydrogen peroxide demand (optimal peroxide/DAT molar ratio for SBP: 2.0 and 3.0 for 2,4-diaminotoluene (2,4-DAT) and 2,6-diaminotoluene (2,6-DAT), respectively; for ARP: 1.5 and 2.75 for 2,4-DAT and 2,6-DAT, respectively) but required significantly less enzyme (0.01 and 0.1 U ml(-1) for 2,4-DAT and 2,6-DAT, respectively) to convert the DAT than ARP (0.4 and 1.5 U ml(-1) for 2,4-DAT and 2,6-DAT, respectively). PEG was shown to have no effect upon the degree of substrate conversion for either enzyme.     

Biosurfactant technology for remediation of cadmium and lead contaminated soils

This research focuses on column experiments conducted to evaluate the potential of environmentally compatible rhamnolipid biosurfactant produced by Pseudomonas aeruginosa strain BS2 to remove heavy metals (Cd and Pb) from artificially contaminated soil. Results have shown that di-rhamnolipid removes not only the leachable or available fraction of Cd and Pb but also the bound metals as compared to tap water which removed the mobile fraction only. Washing of contaminated soil with tap water revealed that approximately 2.7% of Cd and 9.8% of Pb in contaminated soil was in freely available or weakly bound forms whereas washing with rhamnolipid removed 92% of Cd and 88% of Pb after 36 h of leaching. This indicated that di-rhamnolipid selectively favours mobilization of metals in the order of Cd>Pb. Biosurfactant specificity observed towards specific metal will help in preferential elution of specific contaminant using di-rhamnolipid. It was further observed that pH of the leachates collected from heavy metal contaminated soil column treated with di-rhamnolipid solution was low (6.60-6.78) as compared to that of leachates from heavy metal contaminated soil column treated with tap water (pH 6.90-7.25), which showed high dissolution of metal species from the contaminated soil and effective leaching of metals with treatment with biosurfactant. The microbial population of the contaminated soil was increased after removal of metals by biosurfactant indicating the decrease of toxicity of metals to soil microflora. This study shows that biosurfactant technology can be an effective and nondestructive method for bioremediation of cadmium and lead contaminated soil.     

Effect of chelating agents and solubility of cadmium complexes on uptake from soil by Brassica juncea

Brassica juncea, or Indian mustard, was grown in soil artificially contaminated with either a soluble salt, CdCl(2), at 186mg Cdkg(-1), or alternately an insoluble, basic salt, CdCO(3), at 90mg Cdkg(-1). These experiments study the range of Cd uptake by Indian mustard from conditions of very high Cd concentration in a soluble form to the other extreme with an insoluble Cd salt. After plants were established, four different chelating agents were applied. Chelating agents increased plant uptake of Cd from the CdCl(2) soil but did not significantly increase plant uptake of Cd from the CdCO(3) contaminated soil. Addition of ethylenediaminetetraacetic acid (EDTA) increased the plant concentration of Cd by almost 10-fold in soils contaminated with CdCl(2), with a concentration of 1283mg Cdkg(-1) in the dried EDTA-treated plants over a concentration of 131mg Cdkg(-1) in plants without added chelate. However, EDTA increased the aqueous solubility of Cd by 36 times over the soil matrix without added chelator, and thereby, increased the possibility of leaching. Other chelators used in both experiments were ethylenebis(oxyethylenenitrilo)tetraacetic acid, trans-1,2-diaminocyclohexane-N,N,N',N'-tetraacetic acid, and diethylenetriaminepentaacetic acid (DTPA) increasing Cd in plants to 1240, 962, and 437mg Cdkg(-1), respectively. The other chelating agents increased the solubility of Cd in the leachate but not to the extent of EDTA. Comparing all chelating agents studied, DTPA increased plant uptake in terms of Cd in dried plant concentration most relative to the solubility of complexed Cd in runoff water.     

Aerobic degradation of bisphenol A by Achromobacter xylosoxidans strain B-16 isolated from compost leachate of municipal solid waste

A novel bacterium designated strain B-16 was isolated from the compost leachate of the municipal solid waste (MSW) in a laboratory reactor. This strain was identified as a gram-negative bacterium, Achromobacter xylosoxidans that could grow on bisphenol A (BPA, a representative endocrine disruptor) as a sole carbon source under aerobic condition. BPA-degrading characteristics of strain B-16 were investigated in liquid cultures. The results show that BPA degradation was influenced by several factors (e.g. inoculum size, substrate concentration, temperature and pH, etc). The half-lives, optimum temperature and pH were found to be 0.58-3.1d, 35 degrees C and 7.0, respectively. BPA-degrading activity and cell growth were inhibited at high substrate concentration. Metabolic intermediates detected during the degradation process were identified as p-hydroxybenzaldehyde, p-hydroxybenzoic acid and p-hydroquinone, respectively. Metabolic pathway of BPA degradation was proposed in this study.     

Challenges in quantifying biosphere-atmosphere exchange of nitrogen species

Recent research in nitrogen exchange with the atmosphere has separated research communities according to N form. The integrated perspective needed to quantify the net effect of N on greenhouse-gas balance is being addressed by the NitroEurope Integrated Project (NEU). Recent advances have depended on improved methodologies, while ongoing challenges include gas-aerosol interactions, organic nitrogen and N(2) fluxes. The NEU strategy applies a 3-tier Flux Network together with a Manipulation Network of global-change experiments, linked by common protocols to facilitate model application. Substantial progress has been made in modelling N fluxes, especially for N(2)O, NO and bi-directional NH(3) exchange. Landscape analysis represents an emerging challenge to address the spatial interactions between farms, fields, ecosystems, catchments and air dispersion/deposition. European up-scaling of N fluxes is highly uncertain and a key priority is for better data on agricultural practices. Finally, attention is needed to develop N flux verification procedures to assess compliance with international protocols.     

Suspended Particulate Matter Distribution in Rural-Industrial Satna and in Urban-Industrial South Delhi

An air quality sampling program was designed and implemented to collect the baseline concentrations of respirable suspended particulates (RSP = PM₁₀), non-respirable suspended particulates (NRSP) and fine suspended particulates (FSP = PM_2.5). Over a three-week period, a 24-h average concentrations were calculated from the samples collected at an industrial site in Southern Delhi and compared to datasets collected in Satna by Envirotech Limited, Okhla, Delhi in order to establish the characteristic difference in emission patterns. PM_2.5, PM₁₀, and total suspended particulates (TSP) concentrations at Satna were 20.5 ± 6.0, 102.1 ± 41.1, and 387.6 ± 222.4 μg m⁻³ and at Delhi were 126.7 ± 28.6, 268.6 ± 39.1, and 687.7 ± 117.4 μg m⁻³. Values at Delhi were well above the standard limit for 24-h PM_2.5 United States National Ambient Air Quality Standards (USNAAQS; 65 μg m⁻³), while values at Satna were under the standard limit. Results were compared with various worldwide studies. These comparisons suggest an immediate need for the promulgation of new PM_2.5 standards. The position of PM₁₀ in Delhi is drastic and needs an immediate attention. PM₁₀ levels at Delhi were also well above the standard limit for 24-h PM₁₀ National Ambient Air Quality Standards (NAAQS; 150 μg m⁻³), while levels at Satna remained under the standard limit. PM_2.5/PM₁₀ values were also calculated to determine PM_2.5 contribution. At Satna, PM_2.5 contribution to PM₁₀ was only 20% compared to 47% in Delhi. TSP values at Delhi were well above, while TSP values at Satna were under, the standard limit for 24-h TSP NAAQS (500 μg m⁻³). At Satna, the PM₁₀ contribution to TSP was only 26% compared to 39% in Delhi. The correlation between PM₁₀, PM_2.5, and TSP were also calculated in order to gain an insight to their sources. Both in Satna and in Delhi, none of the sources was dominant a varied pattern of emissions was obtained, showing the presence of heterogeneous emission density and that nonrespirable suspended particulate (NRSP) formed the greatest part of the particulate load.