An Analysis of Biomedical Waste Incineration

The California Air Resources Board (ARB) completed a series of source tests of eight operating biomedical waste incinerators (BMWI) under conditions of typical operation. The emissions of certain metals, and chlorinated dioxins and furans in the flue gases of BMWI are relatively high in comparison to emissions from other combustion sources, such as hazardous waste or municipal waste incinerators of modern design. This study reports on an analysis of the status of the existing regulatory framework and the California data base. Clarification of definitional issues at the federal level is needed to effectively treat BMWI management issues. Although few relationships among combustion parameters and emissions were uncovered, patterns of emissions were evident, suggesting commonality and relationships among the waste stream constituents and emissions. Potential implications for future research, operation of BMWI, controls and source reduction and waste segregation strategies are also discussed.     

The Nonlinearity and Related Band Strength of Carbon Monoxide When Applied in Ambient Air Measurement Using Open Long-Path Fourier Transform Infrared Spectrometry

ABSTRACT

The accuracy of CO concentration determination by open-path Fourier transform infrared (FTIR) spectrometry has been re-evaluated in detail. The evaluation focuses on the correction of the calibration curve—the integrated intensity of a standard spectrum—that is used as a comparison spectrum when doing quantitative analysis of CO. Results show that the calibration curve (with 0.5 cm^-1 or 1 cm^-1 resolution) is apparently inclined to be nonlinear under standard conditions, and that the threshold point of nonlinearity is ~0.1 atm-cm. Two commercial FTIR field monitoring systems have been used to investigate the nonlinearity trend. The experimental method consists of using open-path FTIR systems in combination with nondispersive infrared (NDIR) monitors to establish the calibration curve in a semi-closed corridor. The results have been double-checked using closed-cell dynamic equilibrium systems.

When the optical density is larger than a certain value, the curves begin to bend, and when the optical density approaches zero, the band strength is around 178 ± 3 atm^-1 cm^-2 and 173 ± 2 atm^-1 cm^-2, respectively, for 0.5 and 1 cm^-1 resolution at standard temperature and pressure (STP). These values are quite different from other published data that have been acquired by the pressurized method or by high-resolution     

Laboratory and Field Evaluation of Measurement Methods for One-Hour Exposures to O3, PM25, and CO

ABSTRACT

While researchers have linked acute (less than 12-hr) ambient O₃, PM₂₅, and CO concentrations to a variety of adverse health effects, few studies have characterized short-term exposures to these air pollutants, in part due to the lack of sensitive, accurate, and precise sampling technologies. In this paper, we present results from the laboratory and field evaluation of several new (or modified) samplers used in the “roll-around” system (RAS), which was developed to measure 1-hr O₃, PM₂₅, and CO exposures simultaneously. All the field evaluation data were collected during two sampling seasons: the summer of 1998 and the winter of 1999.

To measure 1-hr O₃ exposures, a new active O₃ sampler was developed that uses two nitrite-coated filters to measure O₃ concentrations. Laboratory chamber tests found that the active O₃ sampler performed extremely well, with a collection efficiency of 0.96 that did not vary with temperature or relative humidity (RH). In field collocation comparisons with a reference UV photometric monitor, the active O₃ sampler had an effective collection efficiency ranging between 0.92 and 0.96 and a precision for 1-hr measurements ranging between 4 and 6 parts per billion (ppb). The limits of detection (LOD) of this method were 9 ppb-hr for the chamber tests and ~16 ppb-hr for the field comparison tests.

PM_2.5 and CO concentrations were measured using modified continuous monitors—the DustTrak and the Langan, respectively. A size-selective inlet and a Nafion dryer were placed upstream of the DustTrak inlet to remove particles with aerodynamic diameters greater than 2.5 um and to dry particles prior to the measurements, respectively. During the field validation tests, the DustTrak consistently reported higher PM_2.5 concentrations than those obtained by the collocated 12-hr PM_{2 5} PEM samples, by approximately a factor of 2. After the DustTrak response was corrected (correction factor of 2.07 in the summer and 2.02 in the winter), measurements obtained using these methods agreed well with R² values of 0.87 in the summer and 0.81 in the winter. The results showed that the DustTrak can be used along with integrated measurements to measure the temporal and spatial variation in PM_{2 5} exposures. Finally, during the field validation tests, CO concentrations measured using the Langan were strongly correlated with those obtained using the reference method when the CO levels were above the LOD of the instrument [~1 part per million (ppm)].     

Microwave Process for Volatile Organic Compound Abatement

ABSTRACT

The CHA Corporation has completed the U.S. Air Force Phase II Small Business Innovation Research program to investigate the feasibility of using a novel microwave-based process for the removal and destruction of volatile organic compounds (VOCs) in effluents from noncombustion sources, such as paint booth ventilation streams. Removal of solvents by adsorption, followed by the regeneration of saturated granular activated carbon (GAC) by microwave energy, was achieved in a single fixed-bed reactor. Microwave regeneration of the fixed-bed-saturated carbon restored the original GAC adsorption capacity. After 20 adsorption/regeneration cycles, the adsorption capacity dropped from 13.5 g methyl ethyl ketone (MEK)/100 g GAC to 12.5 g MEK/100 g GAC. During microwave regeneration of the GAC fixed bed, the concentrated desorbed paint solvent was oxidized by passing the solvent mixture through a fixed bed of an oxidation catalyst mixed with silicon carbide in a microwave reactor. A 98% oxidation efficiency was consistently achieved from the oxidation of VOCs in the microwave catalytic reactor.     

Decomposition of Gas Phase 1,3-Butadiene by Ultraviolet/Ozone Process

Abstract

A pilot-scale plug-flow reactor was built to investigate its performance in treating airborne 1,3-butadiene (BD) via ozonation (O₃) and ultraviolet (UV)/O₃ technologies. Governing factors, such as the initial molar ratio of ozone to BD, UV volumetric electric input power, and moisture content in the influent airstream, were investigated. Experiments were conducted at an influent BD concentration of ～50 ppm, an ambient temperature of 26 °C, and a gas retention time of 85 sec. Results show that an initial molar ratio of ozone to BD of 3.5 and 2 sufficed to obtain BD decompositions of >90% for ozonation and UV/O₃, respectively. The UV irradiance did not directly promote the decomposition of BD, rather, it played a role in promoting the production of secondary oxidants, such as hydroxyl radicals. Kinetic analyses indicate that both types of BD decomposition are peudo–first-order with respect to BD concentrations. Moisture content (relative humidity = 40–99%) and UV volumetric electric input power (0.147 and 0.294 W/L) are both factors that weakly affect the rate of BD decomposition. Economic evaluation factors, including both energy of ozone production and UV electric input power, were also estimated.     

Performance measurement for incineration plants using multi-activity network data envelopment analysis: The case of Taiwan

This study proposes the use of multi-activity network data envelopment analysis to appraise how incineration plants in Taiwan perform. Sample data from 2006 is used to examine the trade-offs between efficiency enhancement and pollution abatement. The respective efficiencies of the waste treatment and electricity generation are also assessed in a unified framework. The empirical results indicate that it is more important to improve the efficiency of waste treatment activity than of electricity generation activity in order to enhance the overall performance of Taiwan's incinerators. Since ownership, location and length of operations do not in general affect their performance, any improvement has to come from the careful monitoring of each process of the waste treatment operations. Furthermore, given that the policy in Taiwan has moved away from incineration to recycling, the problem of an over-supply of incinerators may become apparent in the near future. Our results indicate that the availability of capacity size may be an important factor when policy-makers consider whether to close down some existing incinerators.     

CaCl2盐度对活性污泥性能影响的研究

针对某企业高含盐有机生产废水,采用传统活性污泥法,实验研究了氯化钙盐度对活性污泥性能的影响,分别研究了盐度对有机物的去除能力、活性污泥中微生物的耗氧速率、活性污泥的结构和沉淀效果及对菌胶团中微生物生态的影响。结果表明,当氯化钙盐度从0mg/L升高到40000mg/L的时候,废水中COD的去除率由92.9%降低到56%,活性污泥的耗氧速率下降,菌胶团的微生物种类也随之减少,MLVSS/MLSS下降,活性污泥中的无机成分增加,沉淀性能增强,菌胶团也更为致密。     

MBR法/高级氧化技术在中水处理中研究进展

膜生物反应器(MBR)作为一种新型高效的污水处理方法,正受到人们的广泛关注。同时由于高级氧化技术在处理污水过程中无二次污染、易控制,与其他处理过程相结合可提高处理能力,降低处理成本等优点也备受研究者亲睐。本文系统介绍了MBR法的定义、分类、优势及其发展趋势,并对高级氧化技术和中水做了简单说明,阐述了高级氧化技术在膜生物反应器(MBR)中的应用,同时列举了两种工艺相结合在中水处理领域中的作用和地位。     

成都市某污水处理厂污泥处理与处置方式探讨

本文在简要介绍国内几种典型的污泥处理与处置方式基础上,结合成都市某污水处理厂在污泥处理与处置方面的现状以及所存在的问题,提出了以农业利用作为该厂污泥的最终处置方式。