Naphthalene and its biomarkers as measures of occupational exposure to polycyclic aromatic hydrocarbons

Polycyclic aromatic hydrocarbons (PAH) include compounds with two or more fused benzene rings, many of which are carcinogens. Industrial sources produce hundreds of PAH, notably in the coke- and aluminium-producing industries. Because PAH are distributed at varying levels between gaseous and particulate phases, exposure assessment has been problematic. Here, we recommend that occupational exposures to naphthalene be considered as a potential surrogate for occupational PAH exposure for three reasons. Naphthalene is usually the most abundant PAH in a given workplace; naphthalene is present almost entirely in the gaseous phase and is, therefore, easily measured; and naphthalene offers several useful biomarkers, including the urinary metabolites 1- and 2-hydroxynaphthalene. These biomarkers can be used to evaluate total-body exposure to PAH, in much the same way that 1-hydroxypyrene has been applied. Using data from published sources, we show that log-transformed airborne levels of naphthalene are highly correlated with those of total PAH (minus naphthalene) in several industries (creosote impregnation: Pearson r= 0.815, coke production: r= 0.917, iron foundry: r= 0.854, aluminium production: r= 0.933). Furthermore, the slopes of the log-log regressions are close to one indicating that naphthalene levels are proportional to those of total PAH in those industries. We also demonstrate that log-transformed urinary levels of the hydroxynaphthalenes are highly correlated with those of 1-hydroxypyrene among coke oven workers and controls (r= 0.857 and 0.876), again with slopes of log-log regressions close to one. These results support the conjecture that naphthalene is a useful metric for occupational PAH exposure. Since naphthalene has also been shown to be a respiratory carcinogen in several animal studies, it is also argued that naphthalene exposures should be monitored per se in industries with high levels of PAH.     

High frequency monitoring of the coastal marine environment using the MAREL buoy

The MAREL Iroise data buoy provides physico-chemical measurements acquired in surface marine water in continuous and autonomous mode. The water is pumped 1.5 m from below the surface through a sampling pipe and flows through the measuring cell located in the floating structure. Technological innovations implemented inside the measuring cell atop the buoy allow a continuous cleaning of the sensor, while injection of chloride ions into the circuit prevents biological fouling. Specific sensors for temperature, salinity, oxygen and fluorescence investigated in this paper have been evaluated to guarantee measurement precision over a 3 month period. A bi-directional link under Internet TCP-IP protocols is used for data, alarms and remote-control transmissions with the land-based data centre. Herein, we present a 29 month record for 4 parameters measured using a MAREL buoy moored in a coastal environment (Iroise Sea, Brest, France). The accuracy of the data provided by the buoy is assessed by comparison with measurements of sea water weekly sampled at the same site as part of SOMLIT (Service d'Observation du Milieu LIToral), the French network for monitoring of the coastal environment. Some particular events (impact of intensive fresh water discharges, dynamics of a fast phytoplankton bloom) are also presented, demonstrating the worth of monitoring a highly variable environment with a high frequency continuous reliable system.     

Quantitative PCR analysis of house dust can reveal abnormal mold conditions

Indoor mold concentrations were measured in the dust of moldy homes (MH) and reference homes (RH) by quantitative PCR (QPCR) assays for 82 species or related groups of species (assay groups). About 70% of the species and groups were never or only rarely detected. The ratios (MH geometric mean : RH geometric mean) for 6 commonly detected species (Aspergillus ochraceus, A. penicillioides, A. unguis, A. versicolor, Eurotium group, and Cladosporium sphaerospermum) were >1 (Group I). Logistic regression analysis of the sum of the logs of the concentrations of Group I species resulted in a 95% probability for separating MH from RH. These results suggest that it may be possible to evaluate whether a home has an abnormal mold condition by quantifying a limited number of mold species in a dust sample. Also, four common species of Aspergillus were quantified by standard culturing procedures and their concentrations compared to QPCR results. Culturing underestimated the concentrations of these four species by 2 to 3 orders of magnitude compared to QPCR.     

Trace Element Analyses in an Epiphytic Lichen and its Bark Substrate to Assess Suitability for Air Biomonitoring

Total concentrations of Cd, Cr, Fe, Ni, Pb and Zn were compared from October 1996 to April 1998 in Physcia biziana (Massal.) Zhalbr. v. leptophylla Vezda and in the bark of Quercus ilex L. sampled from the same trees at an urban park. Trace metal concentrations were also measured in the bark covered by the lichen thalli. The lichens showed significantly higher Cr, Fe, Ni and Zn concentrations than both uncovered and covered barks. By contrast, both types of barks had higher concentrations of Cd and Pb than lichens. Trace elements showed a wide temporal variation of concentrations both in the lichens and barks. No relationship was found between the analysed matrices as regards the time course of trace element concentrations.     

Organochlorine Pesticide Residues in Wheat and Drinking Water Samples from Jaipur, Rajasthan, India

The organochlorine pesticide contamination in dietary sources has caused serious threat to the human progeny. The present study was therefore conducted to evaluate the pesticide contamination in wheat flour and drinking water from Jaipur City, Rajasthan, India using Gas Chromatograph. All the wheat and water samples were found to be contaminated with various organochlorine pesticide residues of DDT and its metabolites, HCH and its isomers, heptachlor and its expoxide and aldrin. The amount of pesticide detected in wheat flour was higher than the permissible limits prescribed by WHO/FAO. In drinking water only a few pesticides exceeded the permissible limits. Seasonal variations of pesticides residues were also observed during the study period.     

A comparison of X-ray fluorescence and wet chemical analysis of air filter samples from a scrap lead smelting operation

Personal and area air samples were taken at a scrap lead smelter operation in a bullet manufacturing facility. Samples were taken using the 37-mm styrene-acrylonitrile closed-face filter cassette (CFC, the current US standard device for lead sampling), the 37-mm GSP or "cone" sampler, the 25-mm Institute of Occupational Medicine (IOM) inhalable sampler, and the 25-mm Button sampler (developed at the University of Cincinnati). Polyvinylchloride filters were used for sampling. The filters were pre- and post-weighed, and analyzed for lead content using a field-portable X-ray fluorescence (XRF) analyzer. The filters were then extracted with dilute nitric acid in an ultrasonic extraction bath and the solutions were analyzed by inductively coupled plasma optical emission spectroscopy. The 25-mm filters were analyzed using a single XRF reading, while three readings on different parts of the filter were taken from the 37-mm filters. The single reading from the 25-mm filters was adjusted for the nominal area of the filter to obtain the mass loading, while the three readings from the 37-mm filters were inserted into two different algorithms for calculating the mass loadings, and the algorithms were compared. The IOM sampler was designed for material collected in the body of the sampler to be part of the collected sample as well as that on the filter. Therefore, the IOM sampler cassettes were rinsed separately to determine if wall-loss corrections were necessary. All four samplers gave very good correlations between the two analytical methods above the limit of detection of the XRF procedure. The limit of detection for the 25-mm filters (5 microg) was lower than for the 37-mm filters (10 microg). The percentage of XRF results that were within 25% of the corresponding ICP results was evaluated. In addition, the bias from linear regression was estimated. Linear regression for the Button sampler and the IOM sampler using single readings and the GSP using all tested techniques for total filter loading gave acceptable XRF readings at loadings equivalent to sampling at the OSHA 8-hour Action Level and Permissible Exposure Limit. However, the CFC only had acceptable results when the center reading corrected for filter area was used, which was surprising, and may be a result of a limited data set. In addition to linear regression, simple estimation of bias indicated reasonable agreements between XRF and ICP results for single XRF readings on the Button sampler filters, (82% of the individual results within criterion), and on the IOM sampler filters (77% or 61%--see text), and on the GSP sampler filters using the OSHA algorithm (78%). As a result of this pilot project, all three samplers were considered suitable for inclusion in further field research studies.     

Development and validation of methods for environmental monitoring of cyclophosphamide in workplaces

Methods to monitor contamination of workplaces with antineoplastic drugs have been developed and validated. Cyclophosphamide (CP) was used as a model compound as it is one of the most commonly used antineoplastic drugs. A wipe sampling method to detect contamination with CP at surfaces was developed. A personal air sampling method to sample gas and vapour on solid sorbent tubes and particles with filters was also developed. Wipe and filter samples were extracted and sorbent samples were eluted, all with ethyl acetate. The samples were analysed with liquid chromatography tandem mass spectrometry. (2)H(6)-labelled cyclophosphamide was used as an internal standard. The between-day precision was 2-5% for wipe samples, 4-6% for sorbent samples and 3-8% for filter samples. The limit of detection was 0.02 ng CP per sample for the wipe and filter methods and 0.03 ng CP per sample for the solid sorbent method. Wipe sampling on surfaces made of different materials resulted in mean recoveries between 78-106%. The desorption recovery was between 97-102% for the wipe samples, 97% for the sorbent samples and 101% for the filter samples. Samples were stable for up to 2 months at 5 degrees C and -20 degrees C and for about 2 d at room temperature. The developed methods were applied to the measurement of contamination with CP in a hospital pharmacy. Trace amounts of CP, 1.3 and 1.4 ng, were detected on surfaces in the pharmacy.     

Energy-dispersive X-ray fluorescence systems as analytical tool for assessment of contaminated soils

To determine the heavy metal content in soil samples at contaminated locations, a static and time consuming procedure is used in most cases. Soil samples are collected and analyzed in the laboratory at high quality and high analytical costs. The demand by government and consultants for a more dynamic approach and by customers requiring performances in which analyses are performed in the field with immediate feedback of the analytical results, is growing. Especially during the follow-up of remediation projects or during the determination of the sampling strategy, field analyses are advisable. For this purpose four types of ED-XRF systems, ranging from portable up to high performance laboratory systems, have been evaluated. The evaluation criteria are based on the performance characteristics for all the ED-XRF systems such as limit of detection, accuracy and the measurement uncertainty on one hand, and also the influence of the sample pretreatment on the obtained results on the other hand. The study proved that the field portable system and the bench top system, placed in a mobile van, can be applied as field techniques, resulting in semi-quantitative analytical results. A limited homogenization of the analyzed sample significantly increases the representativeness of the soil sample. The ED-XRF systems can be differentiated by their limits of detection which are a factor of 10 to 20 higher for the portable system. The accuracy of the results and the measurement uncertainty also improved using the bench top system. Therefore, the selection criteria for applicability of both field systems are based on the required detection level and also the required accuracy of the results.     

Dioxin-like compounds in pine needles around Tokyo Bay, Japan in 1999

Pine needle samples collected at ten spatially distant sites around Tokyo Bay in 1999 indicated a widespread lower troposphere pollution with ultra-trace dioxin-like compounds such as chlorodibenzo-p-dioxins (PCDDs), -furans (PCDFs), non-ortho- and mono-ortho-chlorobiphenyls (pPCBs), and -naphthalenes (PCNs). Elevated concentration of planar PCBs and the total PCNs were found at the sites which are located innermost to the Bay, suggesting the regional importance of the evaporative nature of the source of pollution by those compounds over this vast area. The concentrations and profiles for PCDDs and PCDFs remained largely uniform. An exception was the site near the town of Tateyama in the Chiba Prefecture, which is the southernmost but also relatively separate from the inner Bay. The site near Tateyama showed somehow background contamination with all compound groups and highly different profiles of PCNs. The principal component analysis (PCA) of the data matrix has revealed that around the Tokyo Bay, apart from the evaporative emission sources for PCNs and PCBs, combustion related processes also play an important role as sources of the ambient air contamination not only with PCDDs/Fs but also with chloronaphthalenes and planar chlorobiphenyls.