Assessment of uncertainty of NO2 measurements by the chemiluminescence method and discussion of the quality objective of the NO2 European Directive

Hereafter, an assessment of the ability of the chemiluminescence method to measure ambient NO2 with an accuracy within 15%, as requested by the data quality objective of European directive 1999/30/CE, is presented. In general, uncertainty is evaluated using the response to reference materials or by means of inter-comparisons used to determine some statistics like repeatability, reproducibility and calibration bias. These are incomplete approaches and the method of the Guide to the Expression of Uncertainty in Measurement, advised by the Directive, should be preferred. In fact, even if it requires a large data set, it allows the relative influence of all possible sources of uncertainty to be studied. The extent of NO2 uncertainty is mainly dependent on the level of NO. It is decreased by NOx and the correlation between NOx and NO. Furthermore, the uncertainty budget reveals that the contribution of accuracy of calibration standard, linearity, converter efficiency and drift of the analyser between calibration checks to the overall uncertainty is less important than the contribution of interference, mainly humidity and PAN in rural areas. The relative expanded uncertainty of the NO2 hourly average exceeds 30% for NO2 concentrations lower than 40 microg m(-3). Nevertheless, the data quality objective of 15% is reached for 200 microg m(-3), the hourly limit value of the European directive. On the contrary, at the limit value on the annual average, 40 microg m(-3), the data quality objective is not met if NO is higher than 100 microg m(-3). However, the data quality objective could be reached by correcting the measurements with the bias due to interference.     

Seasonal variations in physico-chemical characteristics of River Yamuna in Haryana and its ecological best-designated use

Various physico-chemical characteristics of the River Yamuna flowing in Haryana through Delhi were studied in the summer (April 1998) and winter (Jan.-Feb. 1999). Ecological parameters like dissolved oxygen (DO), pH, nitrate (NO3-), sulfate (SO4(2-)), and phosphate (PO4(3-)), were analyzed and compared with standard permissible limits to assess the best-designated use of the river water for various purposes. The river in Delhi upstream was of better quality whereas the Delhi downstream stretch was polluted as indicated by very low DO and high total dissolved solids (TDS), electric conductivity (EC), total hardness, Na+, K+, Cl-, F- and SO4(2-). The differences in various parameters were statistically significant (p < 0.01) when compared for the Delhi upstream and downstream stretches of the river, particularly in summer. DO and TDS were found to be two important parameters, which showed strong correlation with several other parameters and hence can serve as good indices of river water quality. The river tended to recover from the pollution stress after flowing through a distance of about 80 km downstream of Delhi.     

Diffusive sampling of methyl isocyanate using 4-nitro-7-piperazinobenzo-2-oxa-1,3-diazole (NBDPZ) as derivatizing agent

A diffusive sampling method for the determination of methyl isocyanate (MIC) in air is introduced. MIC is collected using a glass fiber filter impregnated with 4-nitro-7-piperazinobenzo-2-oxa-1,3-diazole (NBDPZ). The urea derivative formed is desorbed from the filter with acetonitrile and analyzed by means of high-performance liquid chromatography (HPLC) using fluorescence detection (FLD) with lambdaex = 471 nm and lambdaex = 540 nm. Additionally, a method was developed using tandem mass spectrometric (MS-MS) detection, which was performed as selected reaction monitoring (SRM) on the transition [MIC-NBDPZ + H]+ (m/z 307) to [NBDPZ + H]+ (m/z 250). The diffusive sampler was tested with MIC concentrations between 1 and 35 microg m(-3). The sampling periods varied from 15 min to 8 h, and the relative humidity (RH) was set from 20% up to 80%. The sampling rate for all 15 min experiments was determined to be 15.0 mL min(-1) (using HPLC-FLD) with a relative standard deviation of 9.9% for 56 experiments. At 80% RH, only 15 min sampling gave acceptable results. Further experiments revealed that humidity did not affect the MIC derivative but the reagent on the filter prior to and during sampling. The sampling rate for all experiments (including long term sampling) performed at 20% RH was found to be 15.0 mL min(-1) with a relative standard deviation of 6.3% (N = 42). The limit of quantification was 3 microg m(-3) (LC-MS-MS: 1.3 microg m(-3)) for 15 min sampling periods and 0.2 microg m(-3) (LC-MS-MS: 0.15 microg m(-3)) for 8 h sampling runs applying fluorescence detection.     

Solid-phase microextraction to monitor the sonochemical degradation of polycyclic aromatic hydrocarbons in water

Solid-phase microextraction (SPME) coupled with GC-MS has been used to monitor the degradation of polycyclic aromatic hydrocarbons (PAHs) by ultrasound treatment. Immersion SPME sampling enabled the fast and solventless extraction of target contaminants at the low microg l(-1) concentration level. The developed protocol was found to be linear in the concentration range from 0.1 to 50 microg l(-1) for most target analytes, with the limits of detection ranging between 0.01 and 0.70 microg l(-1) and the relative standard deviations between 4.31 and 27%. The developed SPME protocol was used to follow concentration profiles of aqueous solutions containing 16 PAHs, which were subject to low frequency ultrasonic irradiation. At the conditions employed in this study (80 kHz of ultrasound frequency, 130 W l(-1) of applied electric power density, 30 microg l(-1) of initial concentration for each of the 16 PAHs), sonochemical treatment was found capable of destroying the lower molecular weight PAHs (naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene and pyrene) within 120-180 min of irradiation. The higher molecular weight PAHs were more recalcitrant to ultrasound treatment.     

Multivariate analysis of the bioaccumulation of polychlorinated biphenyls (PCBs) in the marine pelagic food web from the southern part of the Baltic Sea,Poland

The concentration, pattern, bioaccumulation and biomagnification features of many chlorobiphenyl congeners including non- and mono-ortho chlorine substituted members have been determined in a pelagic food chain including mixed phyto- and zooplankton, herring (Clupea harengus), harbour porpoise (Phocoena phocoena) and black cormorants (Phalacrocorax carbo sinensis) collected from the southern part of the Baltic Proper. TCDD (tetrachlorodibenzo-p-dioxin) toxic equivalents (TEQs) in plankton, herring, harbour porpoise and cormorants were 0.42, 5.3, 79 and 2,700 pg g(-1) lipid weight, respectively. Concentrations of total polychlorinated biphenyls (PCBs) in plankton, herring, harbour porpoise and cormorants were 1.9, 120, 8700 and 2,100 ng g(-1) wet weight (210, 1,300, 10,000 and 42,000 ng g(-1) lipid weight) respectively. Herring, harbour porpoise and black cormorant apparently bioaccumulate many PCBs found in their food, and the values of the bioaccumulation factors (BAFs) for PCBs were approximately 10 in herring, 35 in harbour porpoise and up to 300 in breast muscle of cormorants. Harbour porpoise clearly is able to metabolize the most toxic non-ortho PCBs (no. 77, 126 and 169) and a few mono-ortho PCBs (no. 114, 123 and 156), while all non- and mono-ortho PCBs are bioaccumulated by herring. Penta-, hexa- and hepta-CBs were the dominatant homologue classes both in the muscle tissue and liver. PCB congeners nos. 201, 209, 172/192, 194 and 195 were characterized by the largest BAFs (between 100 and 300). Principal component analysis has been used to analyse the interdependences and differences in the CB congener accumulation patterns between the components of the investigated pelagic food web.     

Development of a diffusive sampling method for determination of methyl isocyanate in air

A diffusive sampling method for determination of methyl isocyanate in air has been developed. A glass fibre filter impregnated with 1-(2-methoxyphenyl)piperazine in a commercially available diffusive sampling device was used to collect methyl isocyanate and the derivative formed was analysed with LC-MS/MS. The sampling rate was determined to be 15.6 ml min(-1), with a relative standard deviation of 7.3%. The sampler was validated for sampling periods from 15 min to 8 h, for relative humidities from 20% to 80% and for concentrations from I to 46 microg m(-3). A field validation was also made and the diffusive sampling results showed no difference compared to a pumped reference method. The impregnated filters have to be stored apart from the diffusive sampler housing and loaded into the sampler prior to each sampling.     

用广义λ—分布拟合空气污染数据

广义λ-分布是一个四参数可变通的概率模型,包括多种单变量分布,这一模型可用于表示空气污染浓度的频率分布。本文采用土耳其安卡拉每日的烟和SO_2监测数据,来证明广义λ-分布具有良好的拟合性质。这里还讨论了与分位数估计和拟合优度有关的一些结果,并与经典对数正态分布进行了比较。     

Mobilization of aluminium and deposition on fish gills during sea salt episodes--catchment liming as countermeasure

Episodic events may be critical with respect to aluminium (Al) toxicity in moderately acidified salmon rivers. The present work demonstrates that sea salt episodes enhance the toxicity of Al in acidic rivers. The documented sea salt episode (300 [micro sign]M Cl) mobilized positively charged Al species (0.4 to 1.1 [micro sign]M Al(i)), enhanced the Al accumulation on fish gills (0.9 to 10 [micro sign]mol g(-1) dw) and caused increased stress responses (6 to15 mM blood glucose) in fish. Accumulated Al on gills remained high several days after the episode. The presented results are based on a six-week field study in two tributary rivers on the west coast of Norway. Changes in the river water qualities and Al speciation were followed using in situ fractionation techniques. Al accumulation on gills and stress responses were followed for Atlantic salmon (Salmo salar) kept in tanks continually exposed to the changing water quality. The potential mobilization of Al from the two catchments was studied by extracting soils with diluted seawater (salinity of 3). To counteract Al toxicity, one of the tributary catchments has been limed. The potential mobility of Al by sea salt was lower in limed soils compared to acid soils, and the Al deposition on fish gills (<3.5 [micro sign]mol g(-1) dw) and associated stress responses stayed low during the sea salt episode in the river draining the limed catchment. Thus, for acid river systems in coastal areas, catchment liming should be considered as a useful countermeasure for Al toxicity.     

Suggested protocol for collecting, handling and preparing peat cores and peat samples for physical, chemical, mineralogical and isotopic analyses

For detailed reconstructions of atmospheric metal deposition using peat cores from bogs, a comprehensive protocol for working with peat cores is proposed. The first step is to locate and determine suitable sampling sites in accordance with the principal goal of the study, the period of time of interest and the precision required. Using the state of the art procedures and field equipment, peat cores are collected in such a way as to provide high quality records for paleoenvironmental study. Pertinent field observations gathered during the fieldwork are recorded in a field report. Cores are kept frozen at -18 degree C until they can be prepared in the laboratory. Frozen peat cores are precisely cut into 1 cm slices using a stainless steel band saw with stainless steel blades. The outside edges of each slice are removed using a titanium knife to avoid any possible contamination which might have occurred during the sampling and handling stage. Each slice is split, with one-half kept frozen for future studies (archived), and the other half further subdivided for physical, chemical, and mineralogical analyses. Physical parameters such as ash and water contents, the bulk density and the degree of decomposition of the peat are determined using established methods. A subsample is dried overnight at 105 degree C in a drying oven and milled in a centrifugal mill with titanium sieve. Prior to any expensive and time consuming chemical procedures and analyses, the resulting powdered samples, after manual homogenisation, are measured for more than twenty-two major and trace elements using non-destructive X-Ray fluorescence (XRF) methods. This approach provides lots of valuable geochemical data which documents the natural geochemical processes which occur in the peat profiles and their possible effect on the trace metal profiles. The development, evaluation and use of peat cores from bogs as archives of high-resolution records of atmospheric deposition of mineral dust and trace elements have led to the development of many analytical procedures which now permit the measurement of a wide range of elements in peat samples such as lead and lead isotope ratios, mercury, arsenic, antimony, silver, molybdenum, thorium, uranium, rare earth elements. Radiometric methods (the carbon bomb pulse of (14)C, (210)Pb and conventional (14)C dating) are combined to allow reliable age-depth models to be reconstructed for each peat profile.     

Development of an ombrotrophic peat bog (low ash) reference material for the determination of elemental concentrations

Given the increasing interest in using peat bogs as archives of atmospheric metal deposition, the lack of validated sample preparation methods and suitable certified reference materials has hindered not only the quality assurance of the generated analytical data but also the interpretation and comparison of peat core metal profiles from different laboratories in the international community. Reference materials play an important role in the evaluation of the accuracy of analytical results and are essential parts of good laboratory practice. An ombrotrophic peat bog reference material has been developed by 14 laboratories from nine countries in an inter-laboratory comparison between February and October 2002. The material has been characterised for both acid-extractable and total concentrations of a range of elements, including Al, As, Ca, Cd, Cr, Cu, Fe, Hg, Mg, Mn, Na, Ni, P, Pb, Ti, V and Zn. The steps involved in the production of the reference material (i.e. collection and preparation, homogeneity and stability studies, and certification) are described in detail.