Estimating contaminant mass discharge: a field comparison of the multilevel point measurement and the integral pumping investigation approaches and their uncertainties

In this field study, two approaches to assess contaminant mass discharge were compared: the sampling of multilevel wells (MLS) and the integral groundwater investigation (or integral pumping test, IPT) that makes use of the concentration-time series obtained from pumping wells. The MLS approached used concentrations, hydraulic conductivity and gradient rather than direct chemical flux measurements, while the IPT made use of a simplified analytical inversion. The two approaches were applied at a control plane located approximately 40m downgradient of a gasoline source at Canadian Forces Base Borden, Ontario, Canada. The methods yielded similar estimates of the mass discharging across the control plane. The sources of uncertainties in the mass discharge in each approach were evaluated, including the uncertainties inherent in the underlying assumptions and procedures. The maximum uncertainty of the MLS method was about 67%, and about 28% for the IPT method in this specific field situation. For the MLS method, the largest relative uncertainty (62%) was attributed to the limited sampling density (0.63 points/m(2)), through a novel comparison with a denser sampling grid nearby. A five-fold increase of the sampling grid density would have been required to reduce the overall relative uncertainty for the MLS method to about the same level as that for the IPT method. Uncertainty in the complete coverage of the control plane provided the largest relative uncertainty (37%) in the IPT method. While MLS or IPT methods to assess contaminant mass discharge are attractive assessment tools, the large relative uncertainty in either method found for this reasonable well monitored and simple aquifer suggests that results in more complex plumes in more heterogeneous aquifers should be viewed with caution.     

Assessing the recovery potential of alpine moss-sedge heath: reciprocal transplants along a nitrogen deposition gradient

The potential of alpine moss-sedge heath to recover from elevated nitrogen (N) deposition was assessed by transplanting Racomitrium lanuginosum shoots and vegetation turfs between 10 elevated N deposition sites (8.2-32.9 kg ha⁻¹ yr⁻¹) and a low N deposition site, Ben Wyvis (7.2 kg ha⁻¹ yr⁻¹). After two years, tissue N of Racomitrium shoots transplanted from higher N sites to Ben Wyvis only partially equilibrated to reduced N deposition whereas reciprocal transplants almost matched the tissue N of indigenous moss. Unexpectedly, moss shoot growth was stimulated at higher N deposition sites. However, moss depth and biomass increased in turfs transplanted to Ben Wyvis, apparently due to slower shoot turnover (suggested to result partly from decreased tissue C:N slowing decomposition), whilst abundance of vascular species declined. Racomitrium heath has the potential to recover from the impacts of N deposition; however, this is constrained by the persistence of enhanced moss tissue N contents.     

Printed wiring boards for mobile phones: characterization and recycling of copper

The popularization of mobile phones, combined with a technological evolution, means a large number of scrap and obsolete equipment are discarded every year, thereby causing economic losses and environmental pollution. In the present study, the printed wiring boards scrap of mobile phones were characterized in order to recycle some of the device components, using techniques of mechanical processing, hydrometallurgy and electrometallurgy. The use of the techniques of mechanical processing (milling, particle size classification, magnetic and electrostatic separation) was an efficient alternative to obtain a concentrated fraction (mainly iron in the magnetic fraction and copper in the conductive fraction) and another fraction containing polymers and ceramics. At the end of mechanical processing, a concentrated fraction of metals could be obtained with an average concentration of 60% copper. This concentrated fraction in metals was dissolved in aqua regia and sent to electrowinning to recover 92% of the dissolved copper. The obtained cathodes have a copper content above 95%, which demonstrates the technical feasibility of recovery of copper using the techniques of mechanical processing, hydrometallurgy and electrometallurgy.     

Potential of microalgae as biopesticides to contribute to sustainable agriculture and environmental development

The loss of yields from agricultural production due to the presence of pests has been treated over the years with synthetic pesticides, but the use of these substances negatively affects the environment and presents health risks for consumers and animals. The development of agroecological systems using biopesticides represents a safe alternative that contributes to the reduction of agrochemical use and sustainable agriculture. Microalgae are able to biosynthesize a number of metabolites with potential biopesticidal action and can be considered potential biological agents for the control of harmful organisms to soils and plants. The present work aims to provide a critical perspective on the consequences of using synthetic pesticides, offering as an alternative the biopesticides obtained from microalgal biomass, which can be used together with the implementation of environmentally friendly agricultural systems.     

Auxinic herbicides induce oxidative stress on Cnesterodon decemmaculatus (Pisces: Poeciliidae)

Environmental Science and Pollution Research - Pesticides might increase the production of reactive oxygen species (ROS). Dicamba (DIC) and 2,4-dichlorophenoxyacetic acid (2,4-D) are auxinic...     

Larvicidal and pupicidal activities of eco-friendly phenolic lipid products from Anacardium occidentale nutshell against arbovirus vectors

Environmental Science and Pollution Research - Aedes aegypti and Culex quinquefasciatus are vectors of diseases that constitute public health problems. The discovery of products capable of...     

BIO_ALGAE 2: improved model of microalgae and bacteria consortia for wastewater treatment

Environmental Science and Pollution Research - A new set up of the integral mechanistic BIO_ALGAE model that describes the complex interactions in mixed algal-bacterial systems was developed to...     

Simultaneous removal of metronidazole and Pb(II) from aqueous solution onto bifunctional activated carbons

Environmental Science and Pollution Research - In this work, it was analyzed the behavior of three commercial activated carbons with different textural and chemical properties to adsorb...     

CePO4-TiO2固溶体的NH3-SCR活性

采用共沉淀法合成了不同Ce与Ti摩尔比的CePO₄-TiO₂复合材料,利用XRD、TEM、NH₃-TPD和H₂-TPR技术对其物理化学性质进行了表征,并对其NH₃-SCR活性进行了评价。实验结果表明：随着CePO₄含量的增加,催化剂的活性提高;当Ce与Ti的摩尔比为8:2时催化剂的活性最高,230 ℃的NO转化率达到100%,且具有更广的温度窗口,优于纯CePO₄。表征结果显示,CePO₄与TiO₂形成固溶体后,颗粒尺寸较为均匀,强酸位的数量增多,氧化还原性能提升,从而提高了催化剂的SCR反应活性,同时改善了其抗水抗硫性能。     

Films Made by Blending Poly(ε-Caprolactone) with Starch and Flour from Sagu Rhizome Grown at the Venezuelan Amazons

Starch-based composite films have been proposed as food packaging. In this context, the study of non-conventional starch sources (sagu, Canna edulis Kerr) has worldwide special attention, because these materials can impart different properties as carbohydrate polymers. A thorough study of the matrices used (sagu starch and flour) was carried out. In the same way, thermoplastic starch (TPS)/PCL blend and thermoplastic flour (TFS)/PCL blend were obtained by melt mixing followed by compression moulding containing glycerol as plasticizer. In this study, chemical composition of the matrices and their properties were related with the properties of the developed films. Moisture content, water solubility, X-ray diffraction, thermogravimetric analysis and mechanical and microstructural properties were evaluated in the films. Taking into account the results, the sagu flour has great potential as starchy source for food packaging applications. However, concretely the flour had lower compatibility with the PCL compared to the starch/PCL blend.