Solubility parameters for determining optimal solvents for separating PVC from PVC-coated PET fibers

Poly(vinyl chloride) (PVC) in PVC-coated poly(ethylene terephthalate) (PET) fabrics can be separated through dissolution in a suitable solvent, leaving only the PET fibers. We investigated the solubility of PVC in 30 solvents using swelling tests. The results were compared with those obtained using the Hansen, Gutmann, Swain, E _T(30), and Kamlet–Taft parameters. For this purpose, Gaussian plots of the PVC swellability versus solubility parameter were used to decide the applicability of the solubility parameter system. Only Gutmann’s electron acceptor–donor parameter (AN + DN) and the Kamlet–Taft parameters β and π* could describe the PVC-solvent system satisfactorily. Tetrahydrofuran (THF), methyl ethyl ketone (MEK), N,N-dimethylformamide (DMF), cyclohexanone, and cyclopentanone were tested for separating PVC from PET at different temperatures. THF dissolved PVC at 20 °C, while cyclohexanone and cyclopentanone did so at 40 °C. Traces of PVC remained on the PET fibers when DMF was used. Complete dissolution of PVC was not achieved at any temperature with MEK. The present work shows that solubility parameters are a helpful tool for the search for suitable solvents. It shows also that solubility parameters have to be selected carefully, since their usefulness depends strongly on the polymer properties.     

A comparison of refrigerant management policies and suggestions for improvement in South Korea

HFCs (hydrofluorocarbons) emerged as alternative refrigerants after the production of chlorofluorocarbons was banned and hydrochlorofluorocarbons were phased out, under the Montreal Protocol on Substances that Deplete the Ozone Layer. However, because the Kyoto Protocol considered HFCs as greenhouse gases, and their impact on climate change has been increasing, major developed countries have been strengthening existing regulations on the use of HFCs as refrigerants. South Korea has also passed various legislations related to refrigerant management. However, reports indicate that implementation of these regulations has been ineffective, due to the absence of a specific system for managing the production, use, and disposal phases of refrigerants. To identify and resolve these issues, this study investigates the current state of refrigerant management in South Korea for those three phases. Refrigerant management policies are compared between different legislatures, using the examples of the European Union, United States, and Japan. Based on the findings, five types of measures are suggested to reduce the production and consumption of refrigerants, and to improve refrigerant management regulations in ways that are most appropriate to the South Korean context.     

Electro-dissolution of metal scrap anodes for nickel ion removal from metal finishing effluent

This contribution reports a novel and cost efficient strategy for nickel ion removal from metal finishing effluents by electro-dissolution of scrap aluminium and iron sacrificial anodes. Electro-coagulation of effluent was carried out at 30 mA/cm² current density for 60 min. The nickel ion concentration of electroplating effluent was analysed by Atomic Absorption Spectroscopy. SEM images of iron and aluminium scrap anodes were critically analysed. Parameters such as heavy metal removal, anode dissolution rate with respect to heavy metal removal, reaction kinetics and cost estimation have been elaborately studied. Electro-coagulation at 30 mA/cm² for 60 min using iron and aluminium scrap anodes resulted in 95.9 and 94.1 % nickel ion reduction, respectively, with 0.0094 and 0.0053 g/ppm dissolution rates. The energy consumption for scrap aluminium and iron anodes was 0.0547 kWh/L. Loose internal bonding and spongy surface morphology of used metal scrap render high porosity and active surface area, enhancing reaction rate. Low cost and ready availability of waste scrap makes the process of electro-coagulation economically viable. Thus, the findings from this contribution point decisively at the superiority of waste metal scrap-based anodes for economic and environmentally sustainable heavy metal ion removal from metal finishing effluent.     

Preparation of biochar catalyst with saccharide and lignocellulose residues of corncob degradation for corncob hydrolysis into furfural

This paper presented a novel process for production of furfural by hydrothermal degradation of corncob over biochar catalyst, in which it was prepared with the recycling degradation solution and lignocellulosic solid residues. The biochar catalyst was papered by lignocellulose residues and concentrated saccharide solution, and then impregnated in 0.5 mol/L sulphuric acid at room temperature for 24 h assisted by the ultrasonic vibration. In the system of recycling, 8.8 % lignocellulose residues and 100 % concentrated saccharide solution from corncob hydrolysis have been recycled. Hydrolysis of corncob was carried out at 180 °C for duration of 170 min over the biochar catalyst. The experimental results have shown that the furfural yield of up to 37.75 % and overall corncob conversion rate of 62.00 % could be achieved under optimum operating conditions for the catalysts preparation and the corncob hydrolysis. It is believed that the acid density of 4.27 mmol/g of biochar catalyst makes the SO₃H groups cleave β-1,4 glycosidic linkages effectively and hydrolyze the cellulose and hemicellulose to water-soluble sugars, as well as to facilitate dehydration of xylose to give the product of furfural.     

Mercury flows in a zinc smelting facility in South Korea

To prepare for the international mercury convention, the characteristics of mercury emissions from a zinc smelting facility in South Korea have been reviewed and a material flow analysis (MFA) has been conducted in this research. As inputs into the mercury MFA study, zinc ores and sulfuric acid were examined, whereas wastewater sludge, effluence water, spent catalyst, and emissions from the casting and roasting processes were examined as outputs. Mercury concentrations extracted from end products like zinc ingots, cadmium ingots, and sulfuric acid were then analyzed. Our results showed that the wastewater sludge discharged from the zinc smelting process had a relatively higher concentration of mercury, indicating that the concentration of mercury was further enriched in the wastewater sludge. The wastes discharged through the zinc smelting process should be thoroughly controlled, as results of the MFA showed that approximately 89 % of the mercury contained in the original input was later found in the waste. According to this study, the higher the concentration of mercury within zinc ores at the input stage, the higher is the mercury concentration found in the wastewater sludge at the output stage.     

Life-cycle greenhouse gas emissions and economic analysis of alternative treatments of solid waste from city markets in Vietnam

We utilize life cycle assessment to trace conversion of degradable organic carbon (DOC) contained in organic waste from city markets in Da Nang, Vietnam. Our methodology makes explicit the process of conversion of DOC under aerobic and anaerobic conditions, as well as the balance of nutrients. Greenhouse gas emissions were calculated for six alternative scenarios: (i) anaerobic landfilling (current situation); (ii) semi-aerobic landfilling; (iii) landfill gas capture; (iv) composting; (v) pre-composting before landfill; and (vi) biogas production. We calculate that 1 t of waste in anaerobic landfilling emits 1.70 t CO₂-eq. with life-cycle perspective. Lowest emission occurs in biogas scenario with 0.26 t CO₂-eq./t. Composting occupies an intermediate position with 0.39 t CO₂-eq./t. Likewise, we estimate that cost of emission reduction in solid waste sector of Vietnam is 15.13 US$/t CO₂-eq., given by alternative of composting and taking anaerobic landfilling as reference. On the other hand, if social cost of carbon (SCC) is incorporated lowest cost to treat 1 t of waste is given by composting and semi-aerobic landfilling at discount rate of 5 %. However, using lower discount rates, and consequently higher values of SCC, composting and biogas production become the alternatives with lowest treatment costs.     

Municipal solid waste composition and food loss reduction in Kyoto City

For 35 years, Kyoto City has conducted detailed household waste composition surveys under the guidance of Kyoto University by dividing household waste into approximately 400 categories. In addition, the city has conducted detailed composition surveys of commercial waste generated by businesses. These surveys show that food loss accounts for approximately 40% of total waste, of which leftovers and untouched food account for about 40% in both households and business facilities. Consequently, the annual generation of household and commercial food loss is estimated at about 30,000 tons. Various efforts have been made to reduce waste, including food loss, but further reduction in environmental burden is needed. Thus, Kyoto City revised the ordinance for waste reduction, and in March 2015, formulated a new municipal waste management plan. The plan not only includes the 2Rs (reduce, reuse), but also, for the first time in Japan, sets quantitative targets for reducing food loss. Kyoto City must ensure that the necessary waste reduction measures are clearly explained to the residents and business operators. To ensure that this plan is successful, it is important to clarify concrete actions that residents and business operators should implement, along with their effects.     

Films Made by Blending Poly(ε-Caprolactone) with Starch and Flour from Sagu Rhizome Grown at the Venezuelan Amazons

Starch-based composite films have been proposed as food packaging. In this context, the study of non-conventional starch sources (sagu, Canna edulis Kerr) has worldwide special attention, because these materials can impart different properties as carbohydrate polymers. A thorough study of the matrices used (sagu starch and flour) was carried out. In the same way, thermoplastic starch (TPS)/PCL blend and thermoplastic flour (TFS)/PCL blend were obtained by melt mixing followed by compression moulding containing glycerol as plasticizer. In this study, chemical composition of the matrices and their properties were related with the properties of the developed films. Moisture content, water solubility, X-ray diffraction, thermogravimetric analysis and mechanical and microstructural properties were evaluated in the films. Taking into account the results, the sagu flour has great potential as starchy source for food packaging applications. However, concretely the flour had lower compatibility with the PCL compared to the starch/PCL blend.