Effect of diurnal changes in VOC source strengths on performances of receptor models

Introduction

The effect of diurnal changes in strengths of volatile organic compound (VOC) sources on the performances of positive matrix factorization (PMF) and principal component analysis (PCA) was investigated using ambient measurement results that were taken during daytime and nighttime hours between March 24 and May 14, 2011, within Davutpasa Campus of Yildiz Technical University (Istanbul, Turkey).

Methods

Forty-five VOC species, ranging from C₅ to C₁₁ in volatility, were measured in the samples, 40 of which are included in the analyses. Ambient samples were grouped as daytime, nighttime, and all day datasets, and both PMF and PCA were applied to each dataset. A total of six source groups were extracted from each dataset: solvent use, general industrial paint use, gasoline and diesel vehicle exhausts, and biogenic as well as evaporative emissions. Estimated source contributions showed great diurnal variations.

Results

The results suggested that extraction of possible sources by PCA depends greatly on the number of samples and the strength of the sources, while PMF produced stable results regardless of number of samples and source strengths.

Conclusion

Although PMF was unable to resolve gasoline vehicle and evaporative emissions, it was found to be successful in explaining diurnal fluctuations in source strengths, while the performance of PCA depends on the strength of emission source.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Transformation and biodegradation of 1,2,3-trichloropropane (TCP)

PURPOSE: 1,2,3-Trichloropropane (TCP) is a persistent groundwater pollutant and a suspected human carcinogen. It is also is an industrial chemical waste that has been formed in large amounts during epichlorohydrin manufacture. In view of the spread of TCP via groundwater and its toxicity, there is a need for cheap and efficient technologies for the cleanup of TCP-contaminated sites. In situ or on-site bioremediation of TCP is an option if biodegradation can be achieved and stimulated. This paper presents an overview of methods for the remediation of TCP-contaminated water with an emphasis on the possibilities of biodegradation. CONCLUSIONS: Although TCP is a xenobiotic chlorinated compound of high chemical stability, a number of abiotic and biotic conversions have been demonstrated, including abiotic oxidative conversion in the presence of a strong oxidant and reductive conversion by zero-valent zinc. Biotransformations that have been observed include reductive dechlorination, monooxygenase-mediated cometabolism, and enzymatic hydrolysis. No natural organisms are known that can use TCP as a carbon source for growth under aerobic conditions, but anaerobically TCP may serve as electron acceptor. The application of biodegradation is hindered by low degradation rates and incomplete mineralization. Protein engineering and genetic modification can be used to obtain microorganisms with enhanced TCP degradation potential.     

Particulate matter emission rates from beef cattle feedlots in Kansas-reverse dispersion modeling

Open beef cattle feedlots emit various air pollutants, including particulate matter (PM) with equivalent aerodynamic diameter of 10 microm or less (PM10); however limited research has quantified PM10 emission rates from feedlots. This research was conducted to determine emission rates of PM10 from large cattle feedlots in Kansas. Concentrations of PM10 at the downwind and upwind edges of two large cattle feedlots (KS1 and KS2) in Kansas were measured with tapered element oscillating microbalance (TEOM) PM10 monitors from January 2007 to December 2008. Weather conditions at the feedlots were also monitored. From measured PM10 concentrations and weather conditions, PM10 emission rates were determined using reverse modeling with the American Meteorological Society/U.S. Environmental Protection Agency Regulatory Model (AERMOD). The two feedlots differed significantly in median PM10 emission flux (1.60 g/m2-day for KS1 vs. 1.10 g/m2-day for KS2) but not in PM10 emission factor (27 kg/1000 head-day for KS1 and 30 kg/1000 head-day KS2). These emission factors were smaller than published U.S. Environmental Protection Agency (EPA) emission factor for cattle feedlots.     

Distribution of PAHs and trace metals in urban stormwater sediments: combination of density fractionation,mineralogy and microanalysis

Sediment management from stormwater infiltration basins represents a real environmental and economic issue for stakeholders due to the pollution load and important tonnages of these by-products. To reduce the sediment volumes to treat, organic and metal micropollutant-bearing phases should be identified. A combination of density fractionation procedure and microanalysis techniques was used to evaluate the distribution of polycyclic aromatic hydrocarbons (PAHs) and trace metals (Cd, Cr, Cu, Ni, Pb, and Zn) within variable density fractions for three urban stormwater basin sediments. The results confirm that PAHs are found in the lightest fractions (d?d??3) whereas trace metals are equally distributed within the light, intermediary, and highest fractions (d?d?d?d?>?2.8 g cm^?3) and are mostly in the 2.3?d??3 fraction. The characterization of the five fractions by global analyses and microanalysis techniques (XRD and MEB-EDX) allowed us to identify pollutant-bearing phases. PAHs are bound to the organic matter (OM) and trace metals to OM, clays, carbonates and dense particles. Moreover, the microanalysis study underlines that OM is the main constituent responsible for the aggregation, particularly for microaggregation. In terms of sediment management, it was shown that density fractionation is not suitable for trace metals but could be adapted to separate PAH-enriched phases.     

A new bioseed for determination of wastewater biodegradability: analysis of the experimental procedure

A new bioassay proposed in the patent P201300029 was applied to a pre-treated wastewater containing a mixture of commercial pesticides to simulate a recalcitrant industrial wastewater in order to determine its biodegradability. The test uses a mixture of standardized inoculum of the lyophilized bacteria Pseudomonas putida with the proper proportion of salts and minerals. The results highlight that biodegradation efficiency can be calculated using a gross parameter (chemical oxygen demand (COD)) which facilitates the biodegradability determination for routine water biodegradability analysis. The same trend was observed throughout the assay with the dehydrated and fresh inoculums, and only a difference of 5 % in biodegradation efficiency (E _f) was observed. The obtained results showed that the P. putida biodegradability assay can be used as a commercial test with a lyophilized inoculum in order to monitor the ready biodegradability of an organic pollutant or a WWTP influent. Moreover, a combination of the BOD₅/COD ratio and the P. putida biodegradability test is an attractive alternative in order to evaluate the biodegradability enhancement in water pre-treated with advanced oxidation processes (AOPs).     

Probability analyses of combining background concentrations with model-predicted concentrations

In order to calculate total concentrations for comparison to ambient air quality standards, monitored background concentrations are often combined with model predicted concentrations. Models have low skill in predicting the locations or time series of observed concentrations. Further, adding fixed points on the probability distributions of monitored and predicted concentrations is very conservative and not mathematically correct. Simply adding the 99th percentile predicted to the 99th percentile background will not yield the 99th percentile of the combined distributions. Instead, an appropriate distribution can be created by calculating all possible pairwise combinations of the 1-hr daily maximum observed background and daily maximum predicted concentration, from which a 99th percentile total value can be obtained. This paper reviews some techniques commonly used for determining background concentrations and combining modeled and background concentrations. The paper proposes an approach to determine the joint probabilities of occurrence of modeled and background concentrations. The pairwise combinations approach yields a more realistic prediction of total concentrations than the U.S. Environmental Protection Agency's (EPA) guidance approach and agrees with the probabilistic form of the National Ambient Air Quality Standards.

Implications: EPA's current approaches to determining background concentrations for compliance modeling purposes often lead to “double counting” of background concentrations and actual plume impacts and thus lead to overpredictions of total impacts. Further, the current Tier 1 approach of simply adding the top ends of the background and model predicted concentrations (e.g., adding the 99th percentiles of these distributions together) results in design value concentrations at probabilities in excess of the form of the National Ambient Air Quality Standards.     

Particulate matter speciation profiles for light-duty gasoline vehicles in the United States

Representative profiles for particulate matter particles less than or equal to 2.5 µm (PM_2.5) are developed from the Kansas City Light-Duty Vehicle Emissions Study for use in the U.S. Environmental Protection Agency (EPA) vehicle emission model, the Motor Vehicle Emission Simulator (MOVES), and for inclusion in the EPA SPECIATE database for speciation profiles. The profiles are compatible with the inputs of current photochemical air quality models, including the Community Multiscale Air Quality Aerosol Module Version 6 (AE6). The composition of light-duty gasoline PM_2.5 emissions differs significantly between cold start and hot stabilized running emissions, and between older and newer vehicles, reflecting both impacts of aging/deterioration and changes in vehicle technology. Fleet-average PM_2.5 profiles are estimated for cold start and hot stabilized running emission processes. Fleet-average profiles are calculated to include emissions from deteriorated high-emitting vehicles that are expected to continue to contribute disproportionately to the fleet-wide PM_2.5 emissions into the future. The profiles are calculated using a weighted average of the PM_2.5 composition according to the contribution of PM_2.5 emissions from each class of vehicles in the on-road gasoline fleet in the Kansas City Metropolitan Statistical Area. The paper introduces methods to exclude insignificant measurements, correct for organic carbon positive artifact, and control for contamination from the testing infrastructure in developing speciation profiles. The uncertainty of the PM_2.5 species fraction in each profile is quantified using sampling survey analysis methods. The primary use of the profiles is to develop PM_2.5 emissions inventories for the United States, but the profiles may also be used in source apportionment, atmospheric modeling, and exposure assessment, and as a basis for light-duty gasoline emission profiles for countries with limited data.

Implications: PM_2.5 speciation profiles were developed from a large sample of light-duty gasoline vehicles tested in the Kansas City area. Separate PM_2.5 profiles represent cold start and hot stabilized running emission processes to distinguish important differences in chemical composition. Statistical analysis was used to construct profiles that represent PM_2.5 emissions from the U.S. vehicle fleet based on vehicles tested from the 2005 calendar year Kansas City metropolitan area. The profiles have been incorporated into the EPA MOVES emissions model, as well as the EPA SPECIATE database, to improve emission inventories and provide the PM_2.5 chemical characterization needed by CMAQv5.0 for atmospheric chemistry modeling.