Feasibility of incorporating waste grass clippings (Lolium perenne L.) in particleboard composites

This study investigated some of the important physical (thickness swelling) and mechanical (modulus of rupture, modulus of elasticity and internal bond) properties of single-layer particleboard panels made from eucalyptus (Eucalyptus camaldulensis Dehn.), waste of grass clippings (Lolium perenne L.) and combinations of the two. The chemical properties (pH, holocelluse and alpha cellulose contents, and water, alcohol-benzene and 1% sodium hydroxide solubilities) of the raw materials were also determined. Panels with a 6:94 ratio of grass-to-eucalyptus particles had the required mechanical properties for interior fitments including furniture and general uses. Boards manufactured with 100% grass clippings exhibited the lowest quality. The overall panel properties improved with a lower percentage of grass clippings added. Based on initial results, it also appears that grass should compose no more than 13% to achieve acceptable panel properties for interior fitments and general uses.     

Model-based prediction of long-term leaching of contaminants from secondary materials in road constructions and noise protection dams

In this study, contaminant leaching from three different secondary materials (demolition waste, municipal solid waste incineration ash, and blast furnace slag) to groundwater is assessed by numerical modeling. Reactive transport simulations for a noise protection dam and a road dam (a typical German autobahn), in which secondary materials are reused as base layers, were performed to predict the breakthrough of a conservative tracer (i.e., a salt) and sorbing contaminants (e.g., PAHs like naphthalene and phenanthrene or heavy metals) at the groundwater table. The dam constructions have a composite architecture with soil covers in inclined layers and distinct contrasts in the unsaturated hydraulic properties of the used materials. Capillary barrier effects result in strong spatial variabilities of flow and transport velocities. Contaminant breakthrough curves at the groundwater table show significant tailing due to slow sorption kinetics and a wide distribution of travel times. While conservative tracer breakthrough depends primarily on subsoil hydraulic properties, equilibrium distribution coefficients and sorption kinetics represent additional controlling factors for contaminant spreading. Hence, the three secondary materials show pronounced differences in the temporal development of leached contaminant concentrations with consequences for breakthrough times and peak concentrations at the groundwater table. Significant concentration reductions due to dispersion occur only if the source concentrations decrease significantly prior to the arrival of the contaminant at the groundwater table. Biodegradation causes significant reduction of breakthrough concentrations only if flow velocities are low.     

Geopolymerisation of silt generated from construction and demolition waste washing plants

Recycling plants that size, sort and wash construction and demolition waste can produce high quality aggregate. However, they also produce up to 80ton per hour of filter cake waste containing fine (<63mum) silt particles that is classified as inert waste and normally landfilled. This research investigated the potential to form geopolymers containing silt, which would allow this problematic waste to be beneficially reused as aggregate. This would significantly improve the economic viability of recycling plants that wash wastes. Silt filter cakes have been collected from a number of aggregate washing plants operating in the UK. These were found to contain similar aluminosilicate crystalline phases. Geopolymer samples were produced using silt and silt mixed with either metakaolin or pulverised fuel ash (PFA). Silt geopolymers cured at room temperature had average 7-day compressive strengths of 18.7MPa, while partial substitution of silt by metakaolin or PFA increased average compressive strengths to 30.5 and 21.9MPa, respectively. Curing specimens for 24h at 105 degrees C resulted in a compressive strength of 39.7MPa and microstructural analysis confirmed the formation of dense materials. These strengths are in excess of those required for materials to be used as aggregate, particularly in unbound applications. The implications of this research for the management of waste silt at construction and demolition waste washing plants are discussed.     

Comparative study on the characteristics of fly ash and bottom ash geopolymers

This research was conducted to compare geopolymers made from fly ash and ground bottom ash. Sodium hydroxide (NaOH) and sodium silicate (Na(2)SiO(3)) solutions were used as activators. A mass ratio of 1.5 Na(2)SiO(3)/NaOH and three concentrations of NaOH (5, 10, and 15M) were used; the geopolymers were cured at 65 degrees C for 48 h. A Fourier transform infrared spectrometer (FT-IR), differential scanning calorimeter (DSC), and scanning electron microscope (SEM) were used on the geopolymer pastes. Geopolymer mortars were also prepared in order to investigate compressive strength. The results show that both fly ash and bottom ash can be utilized as source materials for the production of geopolymers. The properties of the geopolymers are dependent on source materials and the NaOH concentration. Fly ash is more reactive and produces a higher degree of geopolymerization in comparison with bottom ash. The moderate NaOH concentration of 10 M is found to be suitable and gives fly ash and bottom ash geopolymer mortars with compressive strengths of 35 and 18 MPa.     

Bench-scale composting of source-separated human faeces for sanitation

In urine-diverting toilets, urine and faeces are collected separately so that nutrient content can be recycled unmixed. Faeces should be sanitized before use in agriculture fields due to the presence of possible enteric pathogens. Composting of human faeces with food waste was evaluated as a possible method for this treatment. Temperatures were monitored in three 78-L wooden compost reactors fed with faeces-to-food waste substrates (F:FW) in wet weight ratios of 1:0, 3:1 and 1:1, which were observed for approximately 20 days. To achieve temperatures higher than 15 degrees C above ambient, insulation was required for the reactors. Use of 25-mm thick styrofoam insulation around the entire exterior of the compost reactors and turning of the compost twice a week resulted in sanitizing temperatures (>or=50 degrees C) to be maintained for 8 days in the F:FW=1:1 compost and for 4 days in the F:FW=3:1 compost. In these composts, a reduction of >3 log(10) for E. coli and >4 log(10) for Enterococcus spp. was achieved. The F:FW=1:0 compost, which did not maintain >or=50 degrees C for a sufficiently long period, was not sanitized, as the counts of E. coli and Enterococcus spp. increased between days 11 and 15. This research provides useful information on the design and operation of family-size compost units for the treatment of source-separated faeces and starchy food residues, most likely available amongst the less affluent rural/urban society in Uganda.     

Management of MSW in Spain and recovery of packaging steel scrap

Packaging steel is more advantageously recovered and recycled than other packaging material due to its magnetic properties. The steel used for packaging is of high quality, and post-consumer waste therefore produces high-grade ferrous scrap. Recycling is thus an important issue for reducing raw material consumption, including iron ore, coal and energy. Household refuse management consists of collection/disposal, transport, and processing and treatment - incineration and composting being the most widely used methods in Spain. Total Spanish MSW production exceeds 21 million tons per year, of which 28.1% and 6.2% are treated in compost and incineration plants, respectively. This paper presents a comprehensive study of incineration and compost plants in Spain, including a review of the different processes and technologies employed and the characteristics and quality of the recovered ferrous scrap. Of the total amount of packaging steel scrap recovered from MSW, 38% comes from compost plants and 14% from incineration plants. Ferrous scrap from incineration plants presents a high degree of chemical alteration as a consequence of the thermal process to which the MSW is subjected, particularly the conditions in which the slag is cooled, and accordingly its quality diminishes. Fragmentation and magnetic separation processes produce an enhancement of the scrap quality. Ferrous scrap from compost plants has a high tin content, which negatively affects its recycling. Cleaning and detinning processes are required prior to recycling.     

Leachate recirculation effects on waste degradation: study on columns

The purpose of this study is to determine the impact of leachate recirculation on the degradation of municipal solid wastes (bioreactor concept). The study was carried out using columns containing approximately 50 kg of waste, in order to follow waste degradation over a limited time. Three types of waste were studied: fresh waste of standard composition, fresh waste of fermentable composition and some 8-yr-old waste extracted from a site in France. Measurement of the global parameters, such as chemical oxygen demand (COD), volatile acidity, alkalinity, leachate conductivity, methane potential of the wastes and biogas production monitoring (volume of CO2 and CH4 produced), were carried out. The quantity of oxydizable matter and biogas production was increased by the leachate recirculation, and the duration of the first degradation phases was reduced in all cases. Chloride, ammonium and organic pollution accumulation was observed according to the duration of recirculation. After 400 days of degradation, waste stabilization seemed to be reached for all of the recirculated columns (COD<300 mg/L O2, and methane potential reached).     

Diel cycles of arsenic speciation due to photooxidation in acid mine drainage from the Iberian Pyrite Belt (Sw Spain)

Twenty four hours diel cycles of arsenic speciation in Acid Mine Drainage (AMD) due to photooxidation have been reported for the first time. AMD samples were taken during 48 h (31st March and 1st April, 2005) at 6 h intervals from the effluent of a massive abandoned polymetallic sulphide mine of the Iberian Pyrite Belt (Sw Spain). Samples were preserved in situ using cationic exchange prior to analysis by coupled high performance liquid chromatography, hydride generation and atomic fluorescence spectrometry (HPLC-HG-AFS) for arsenic speciation. The results indicated the presence of inorganic arsenic species with daily means of 262mugl(-1) for As(V) and 107 microg l(-1) for As(III). No marked diel trend was observed for As(V). However, a marked diel trend was observed for As(III) in the two studied days, with maximum concentrations during nighttime (141-143 microg l(-1)) and minimum concentrations at daytime (72-77 microg l(-1)). This difference in concentration during daytime and nighttime is ca. 100%. A similar diel cycle was observed for iron. An explanation for the arsenic diel cycles observed is the light induced photooxidation of As(III) and the elimination of As(V) due to its adsorption onto Fe precipitates during the daytime. Furthermore, the diel changes in arsenic speciation emphasize the importance of designing suitable sampling strategies in AMD systems.     

Remediation of hydrocarbons in crude oil-contaminated soils using Fenton’s reagent

Sandy soil samples spiked with Bonny light crude oil were subsequently treated with Fenton's reagent at acidic, neutral, and basic pH ranges. Oil extracts from these samples including an untreated one were analyzed 1?week later with a gas chromatograph to provide evidence of hydrocarbon depletion by the oxidant. The reduction of three broad hydrocarbon groups-total petroleum hydrocarbon (TPH); benzene, toluene, ethylbenzene, and xylene (BTEX); and polycyclic aromatic hydrocarbon (PAH) were investigated at various pHs. Hydrocarbon removal was efficient, with treatment at the acidic pH giving the highest removal of about 96% for PAH, 99% for BTEX, and some TPH components experiencing complete disappearance. The four-ringed PAHs were depleted more than their three-ringed counterparts at the studied pH ranges.