雷管壳体安全检测过程的模拟与检测时间的确定

采用数值模拟与现场试验相结合的方法,分析了带缺陷雷管在气压检测过程中气体的泄漏过程,确定了最佳的检测时间。采用Fluent建立了缺陷雷管正气压检测模型,分析了缺陷在不同位置处的气体泄漏过程,研究了气体泄漏过程中,雷管内部气压的分布及其随时间变化过程,结果表明:距雷管顶端的缺陷因尺寸较大,所以该泄漏点的压强要大于侧壁处,而气体泄漏流速小于侧壁处,综合分析缺陷处和雷管内部的气体压降过程及试验,可确定4s为最佳的充气时间,5s作为最佳的雷管质量诊断时间。     

氢安全研究现状及面临的挑战

氢能具有储运便捷、来源多样、洁净环保等突出优点,许多国家把发展氢能作为重要的能源战略。氢安全是氢能大规模商业化应用的重要保障。在分析国内外氢安全领域近年来最新研究进展的基础上,依次从氢泄漏与扩散、氢燃烧与爆炸、氢与金属材料相容性及氢风险评价等方面,系统总结了国内外氢安全研究面临的挑战,并对我国氢安全的发展提出了建议。     

CO2浓度升高对半干旱区春小麦光合作用及水分生理生态特性的影响

大气CO₂浓度升高已成为世界范围内重要环境问题。为了解大气CO₂浓度升高对春小麦光合作用及水分生理生态特性的影响,在典型半干旱区定西利用开顶式气室(OTC)试验平台,以春小麦“定西24号”为供试品种,开展了CO₂浓度增加模拟试验。试验设对照(390μmol·mol^?1)、480μmol·mol^?1和570μmol·mol^?1等3个CO₂浓度(摩尔分数)梯度。结果表明:在对照和增加CO₂浓度条件下,春小麦叶片净光合速率和蒸腾速率日变化均呈“双峰型”分布,出现明显的“午休”现象;胞间CO₂浓度的日变化表现为斜“V”字型曲线;叶水势日变化呈现反抛物线曲线走向,在中午后出现水势曲线拐点。在不同生育时期内,净光合速率、气孔导度和胞间CO₂浓度均表现为开花期最大,乳熟期最小。而蒸腾速率表现为开花期最大,拔节期最小,叶片水平水分利用效率表现为孕穗期最大,乳熟期最小。随着CO₂浓度升高,春小麦叶片净光合速率、胞间CO₂浓度、水分利用效率和水势提高,气孔导度和蒸腾速率降低。与对照大气CO₂浓度相比,在480μmol·mol^?1浓度和570μmol·mol^?1浓度下,整个生育期净光合速率平均分别提高了14.68%和28.20%,气孔导度平均降低了15.29%和24.83%,胞间CO₂浓度平均提高了10.38%和26.15%,蒸腾速率平均减小了6.63%和12.41%,WUE平均增加了22.9%和46.9%。随着CO₂浓度升高,蒸腾失水减少,叶片水势不断增加,从而增强了春小麦对干旱胁迫的抵御能力。研究结果为我国半干旱区春小麦对全球气候变化下的敏感性及适应性提供理论参考。     

浸油生物质厌氧消化产甲烷的最佳投料周期探究

厌氧消化需要保持在较高甲烷产量的前提下连续产气,本研究使用浸油生物质进行厌氧消化,在最佳厌氧消化实验条件下采用间歇式进料的方式,分别设置在产甲烷初期、最高期、下降期及末期进行投料,考察各个投料阶段对厌氧消化产甲烷的影响。结果表明:比较理想的间歇式进料周期为产甲烷下降期的第35 d,其甲烷产量比添加原料前提高了39.9%,产气总量为3 496.165 m L。     

包钢干熄焦除尘灰用于高炉喷吹的研究

为研究包钢干熄焦除尘灰代替部分高炉喷吹用煤,对干熄焦除尘灰进行了工业分析和微观形貌分析,采用热重分析仪对干熄焦除尘灰和高炉喷吹用煤的着火点、燃尽温度、燃尽时间、综合燃烧特性指数以及动力学参数进行了分析,探讨了干熄焦除尘灰配入量对高炉喷吹性能的影响。研究结果表明:活化能随干熄焦除尘灰配入量的增加而增大,燃烧性能降低,干馏烟煤、无烟煤、半焦和干熄焦除尘灰(配比为40%30%25%5%)搭配组成的混合煤燃烧性能最好。     

含阶梯结构的高层楼梯井内烟气湍流及输运特征量的全局敏感性分析

高层建筑竖井火灾中影响因素众多,并且各因素对高层楼梯井火灾中重要现象、关键数值等的影响大小不一,使得此类火灾中的实验或理论研究成本较高。通过建立全局敏感性分析平台,定量考察了高层楼梯井结构所涉及因素的影响大小,并能够方便地筛选掉对所考察量影响较小的因素,以降低实验或计算成本。使用数值模拟方法,通过CFD软件对包含阶梯几何框架的高层楼梯井结构火灾进行了共计60次工况计算。并且根据计算结果,使用全局参数敏感性分析方法,得出建筑尺寸、热释放速率、环境参数对高层楼梯井内烟气湍流特性及输运特性的敏感性排序。结果表明,火源热释放速率对各输出参数的影响均占38%以上。     

Determination of trace metal concentrations in soil profiles of municipal waste dumps in Nigeria

The concentrations of trace metals (Cd, Pb, Cu, Cr, Fe, Ni, Zn and Co) were studied in soil profiles of eight municipal waste dump sites in Warri metropolis. The results indicate that concentrations of trace metals varied widely among the different dumpsites and decreased with depths in a studied soil profile. The accumulation pattern for the heavy metals in the soil profiles follows the order: Fe > Pb > Mn > Co > Cr > Zn > Ni > Cu > Cd. The concentrations of metals found in these sites was below the Canadian remediation criteria for land for agricultural, residential and commercial/industrial purposes except for the cadmium levels in some sites that exceeded criterion values for agricultural and residential. In such sites, remedial actions are required before any form of chosen development can take place. The levels of heavy metals found in these dump sites were higher than that of the control site. The examined metals showed no significant correlation with soil physicochemical properties at the surface horizon, which is suggestive evidence that these metals arise from anthropogenic input.     

Critical Review of Norms and Standards for Biodegradable Agricultural Plastics Part II: Composting

The critical review of norms and standards and corresponding tests to determine the compostability of biodegradable plastics, possibly applicable also to biodegradable agricultural plastics, shows that many norms concerning testing and labelling of compostable plastics have been established at the international level. Some of them are about plastic materials, some others are about products like packaging. The media and conditions of testing cover mainly the conditions designed for industrial composting facilities, and only a few concern home composting conditions. Considering that the end of life management of biodegradable agricultural plastic products will be done at the farm to reduce the management of the waste and also its cost, only a few of these norms are considered to be suitable for adaptation to cover also biodegradable agricultural plastic products. The biodegradability validation criteria under composting conditions, such as the threshold percentage of biodegradation and disintegration, the time and temperature, and the ecotoxicity, are presented for the main norms and standard testing methods. Based on these different norms and their content, a list of specs and technical requirements that could be adapted to meet farm composting conditions for agricultural compostable plastics is proposed. These requirements may be used as criteria for the establishment of a new integrative norm for agricultural compostable plastics.     

制备和再生方式对半焦吸附剂烟气脱硝性能的影响

以廉价的半焦为原料,利用半焦改性活化后具有孔网结构丰富、吸附催化性能好,且机械强度高等优良特性制备半焦吸附剂,采用固定床反应器进行烟气脱硝性能评价,并借助BET和TEM等手段研究影响脱硝性能的主要因素.结果表明,高压水热活化和硝酸氧化高温热处理两种改性制备方式以及热脱附、水洗和氨水洗等再生方式都能够显著影响半焦吸附剂的表面物性和脱硝性能.     

Research on Methods for Building Volcano Disaster Information System--taking Changbai Mountain as an example

1IntroductionAs a many-volcano-distributed country,China is covered with many volcanoes and lava rocks.A-mong the one-thousand-or-so volcanoes,Changbai Mountain Volcano,Wudalianchi Volcano,Tengchong Volcano and Ashikule Volcano of West Kunlun are the mostlatentcatastrophic erup-tive active volcanoes.In recent years,the activity of the earth' s crust in some volcanic areas isobviously becoming increasing violent.Butfew scholars have monitored and evaluated volcano inChina.So building VDI…