Resourcefulization approaches to pollution control of chromate residues in China

Over 2 million tons of chromate residues as hazardous wastes have been accumulated from chromate production processes during the past more than 30 years in China. Some serious pollution problems have been caused due to no appropriate technology and management. Approaches are reviewed to pollution control of chromate residues by utilizing them as secondary resources in this paper. In addition to legislation for pollution control, chromate residues can be used as raw materials to produce a great diversity of useful industrial products. Strategies are also recommanded for the resourcefulization of chromate residues.     

Equilibrium and kinetic studies on the adsorption of aniline compounds from aqueous phase onto bifunctional polymeric adsorbent with sulfonic groups

In the present study, a hydrophilic bifunctional polymeric resin (LS-2) with sulfonic groups was synthesized, and the adsorption performance of three aniline compounds, aniline, 4-methylaniline, and 4-nitroaniline onto LS-2 was compared with that on the commercial Amberlite XAD-4. The uptake of the aniline compounds on LS-2 is a procedure of coexistence of physisorption and chemisorption and obeys the pseudo-second order rate equation, while the uptake of the compounds on XAD-4 is merely a physical adsorption and follows the pseudo-first order rate equation. All the isothermal data fit well with the Freundlich model, and the values of K(F) of the compounds adsorbing on LS-2 are much higher than those on XAD-4 suggesting the higher adsorbing capacities on LS-2 than those on XAD-4, which may be attributed to the microporous structure and the polar groups on the network of LS-2 resin. Dynamic adsorption and desorption studies for aniline on LS-2 show that the breakthrough adsorption capacity and the total adsorption capacity are 0.96 and 1.24 mmol per milliliter resin, respectively. Nearly 100% regeneration efficiency for the adsorbent was achieved by 5% hydrochloric acid.     

微电解-催化氧化-A/O法处理苯硫酚废水

采用微电解—催化氧化—A／O工艺处理苯硫酚生产废水，结果表明，该工艺对CODcr、石油类、挥发酚、苯、甲苯各项污染物指标均有较好的去除效果，整个工艺运行稳定。只要控制好各个处理环节，出水水质能达到国家一级排放标准。     

脉冲供电在锌沸腾炉电除尘器上的应用

介绍了一种电除尘器脉冲供电的基本原理及其在锌沸腾炉电除尘器上的应用试验情况。结果表明，在基本保持同一工况条件下，脉冲供电比直流供电降低出口烟气含尘浓度50.4%～79.6%；脉冲供电能改善电除尘器运行性能，提高电除尘器改善系数达1.32；脉冲供电运行安全可靠。     

固定化微生物脱氮技术

在废水生物脱氮中 ,利用载体固定、形成颗粒污泥等固定化微生物技术可在增加生物脱氮速度、节省碳源、减少后曝气等方面提供有效的方法 ,并实现单级生物脱氮     

铁黄生产中废水处理与废渣的回收利用

介绍了氧化铁黄生产中的废水治理情况，同时其产生的废渣可回收利用。经过治理产生的环境、经济和社会效益显著。     

宁波-舟山海域入海污染物环境容量研究

在宁波-舟山海域数值模拟潮流场的基础上,建立了该海域各污染源的响应系数场,计算了主要污染源COD、无机氮和活性磷酸盐的分担率场,及各污染源和控制单元的环境容量.研究结果将为该海域入海污染物总量控制提供科学依据.     

二氧化氯销毁氰化物的应用研究

在弱碱性条件下,二氧化氯消毒剂将氰化物氧化成无毒的氰酸盐(OCN-)、二氧化碳和氮气.研究了影响二氧化氯销毁氰化物的几种因素:pH在8～11的范围内,不影响二氧化氯对氰化物的销毁率;在所试验的反应温度(0～40℃)内,温度对反应速率表现出有限的影响;二氧化氯与氰离子的最佳质量比为2:1;当氰离子最高使用浓度小于0.5 g/L时,废水中氰离子浓度达一级以上的排放标准.     

曝气生物滤池处理焦化废水脱氮的研究

用曝气生物滤池处理焦化废水的研究表明,在曝气量(Q)=0.25L/min,温度(T)=20℃,pH=8,反冲洗周期为3个运行周期内,NH3-N的去除速率达44 mg/L·h.同时在滤池中出现了亚硝酸盐积累现象,且受反冲洗的影响较大.     

各种影响因子对电解法预处理医药废水的影响研究

探讨了电解法预处理医药废水时停留时间、电解电压、废水初始浓度、温度和废水pH值等影响因子对去除色度、COD和提高废水可生化性等处理效果的影响，并考察了其应用于工业实际废水处理的可行性。实验结果表明：电解法更适合高浓度医药废水的处理，色度的去除率可达到90％以上；电解时间宜控制在40-60min；电解电压越高，废水COD和色度去除效果越好；在实验温度范围内，温度对色度和COD去除率的影响不大；废水pH值为7．5时电解效果最佳，工程运用宜控制在6—9之间。