低碳经济发展中物流绿色发展趋势研究

文中主要对低碳经济发展中物流绿色发展趋势进行了研究,介绍了对低碳经济发展物流绿色发展评价,探讨了低碳经济发展中的不同问卷的调查结果,对物流绿色发展的认知、态度和行动进行了论述,在论述过程中,主要包括对低碳经济发展中的物流认知、对低碳经济发展中的物流态度、对低碳经济发展中的物流行动和对发展低碳经济物流的认知、态度与行动的比较,最后给出了低碳经济发展中物流绿色发展趋势,对低碳经济发展中物流绿色发展给出了研究基础。     

等离子体处理的时效性对芳Ⅲ/双马复合材料耐湿热性能的影响

目的考察等离子体处理前后及其时效性对芳Ⅲ/双马复合材料弯曲强度、界面性能及耐湿热性能的影响。方法用低温射频耦合等离子体处理芳纶纤维表面,分别将未处理的、等离子体刚处理过的和等离子体处理后在空气中放置三天后的纤维通过溶液预浸渍工艺制备芳Ⅲ/双马复合材料预浸料,再经过高温模压成形技术制备芳Ⅲ/双马复合材料单向板。采用万能材料试验机对水煮前后复合材料的弯曲强度和层间剪切强度进行测试,利用扫描电子显微镜对复合材料层间剪切破坏形貌进行观察。结果等离子体处理后,复合材料的吸水率由未处理时的0.51%下降到0.33%,复合材料层间剪切强度由49.4 MPa提高到62.9 MPa。等离子体处理时效后复合材料的吸水率增加到0.69%,复合材料的层间剪切强度下降到56.0 MPa。结论等离子体处理提高了复合材料界面性能,但等离子体处理的时效后,复合材料的界面性能及其耐湿热性能有所下降。等离子体处理及时效性对复合材料的弯曲强度和耐湿热性能变化不大。     

阳极溶出伏安法、石墨炉原子吸收法测定海水中总铬的方法比较研究

铬是海洋水体中的痕量重金属之一,海水的高盐基体对铬的测定有严重的干扰,而且海水中同时存在Cr(Ⅲ)和Cr(Ⅵ),两种不同价态给测定也带来了一定难度。文章从Cr(Ⅲ)的氧化率、方法检出限、精密度、实际样品加标等方面对过氧化氢氧化-阳极溶出伏安法与传统的MIBK萃取-无火焰原子吸收分光光度法进行了比较研究,发现两种方法在测试结果上无显著差异,但是过氧化氢氧化-阳极溶出伏安法具有更高的精密度,更低的检出限,且对Cr(Ⅲ)的回收率略有提升。     

关于高校绿色教育环境下中华传统体育文化探讨

针对高校绿色教育环境下中华传统体育文化的探讨问题,给出了高校绿色教育的基本理论,包括高校绿色教育的概念,高校绿色教育的特点,包括高校绿色教育的生命性、高校绿色教育的生活性、高校绿色教育的人文性和高校绿色教育的内容与实践,探讨了高校绿色教育环境与中华传统体育文化的发展,包括高校绿色教育环境与中华传统体育文化的价值、高校绿色教育环境与中华传统体育文化的发展,最后,对高校绿色教育环境与中华传统体育文化的互动进行了说明。     

Population structure and sex-change in the coral-inhabiting snailCoralliophila violacea at Hsiao-Liuchiu,Taiwan

Surveys of the coral-inhabiting snailCoralliophila violacea (Lamarck) (=C. neritoidea Kiener) were made on shallow fringing reefs (<8 m deep) around Hsiao-Liuchiu, Taiwan, between July and October 1990. The snails were aggregated into patches on the surface of massive poritid coral colonies. Coral colonies >40 cm in diameter were more likely to bear patches of snails than smaller colonies, and also to have more snails. The coralliophilids ranged from 5 to 30 mm in aperture length. The sex ratio of the population was biased toward males (539:279), with only a few small individuals of indistinguishable sex. Snails between 6 and 10 mm were all males, while most snails with aperture lengths 20 mm were females. Judging from the distinct size ranges of males and females within patches and from the observed degeneration of the penis, the snails may have changed sex from male to female with increasing size. Sex-change may occur across a wide size range (10 to 20 mm). The correlation of smallest female size and largest male size among patches indicates that snail size at sex-change is peculiar to each individual patch. Those females in patches with a single female (but many males) were significantly smaller than females in multiple-female patches. It is likely that in the absence of females males change sex at a smaller size, whereas in the presence of large females males delay sexchange until they have reached a larger size. The plasticity of size at sex-change may be adaptive and a result of natural selection at the individual level.     

青铜峡铝厂氟污染对广武乡玉米影响的调查分析

监测了青铜峡铝厂东南方向４．５ｋｍ的广武乡玉米叶，得知含氟量为４３．９４－１６６．１ｍｇ／ｋｇ，对照样品树新林场玉米叶的含氟均值为１３．１５ｍｇ／ｋｇ，广武乡的玉米受到了严重的氟污染，农作物减产严重。     

水中Mg~(2+)的测试管快速测定

研制了一种测定水中Mg2 + 的测试管 ,测定范围为 0 .5mg/L～ 2 .0mg/L。该测试管适用于现场应急监测 ,具有快速、简便、抗干扰能力强和价格低廉等特点     

Suggested protocol for collecting, handling and preparing peat cores and peat samples for physical, chemical, mineralogical and isotopic analyses

For detailed reconstructions of atmospheric metal deposition using peat cores from bogs, a comprehensive protocol for working with peat cores is proposed. The first step is to locate and determine suitable sampling sites in accordance with the principal goal of the study, the period of time of interest and the precision required. Using the state of the art procedures and field equipment, peat cores are collected in such a way as to provide high quality records for paleoenvironmental study. Pertinent field observations gathered during the fieldwork are recorded in a field report. Cores are kept frozen at -18 degree C until they can be prepared in the laboratory. Frozen peat cores are precisely cut into 1 cm slices using a stainless steel band saw with stainless steel blades. The outside edges of each slice are removed using a titanium knife to avoid any possible contamination which might have occurred during the sampling and handling stage. Each slice is split, with one-half kept frozen for future studies (archived), and the other half further subdivided for physical, chemical, and mineralogical analyses. Physical parameters such as ash and water contents, the bulk density and the degree of decomposition of the peat are determined using established methods. A subsample is dried overnight at 105 degree C in a drying oven and milled in a centrifugal mill with titanium sieve. Prior to any expensive and time consuming chemical procedures and analyses, the resulting powdered samples, after manual homogenisation, are measured for more than twenty-two major and trace elements using non-destructive X-Ray fluorescence (XRF) methods. This approach provides lots of valuable geochemical data which documents the natural geochemical processes which occur in the peat profiles and their possible effect on the trace metal profiles. The development, evaluation and use of peat cores from bogs as archives of high-resolution records of atmospheric deposition of mineral dust and trace elements have led to the development of many analytical procedures which now permit the measurement of a wide range of elements in peat samples such as lead and lead isotope ratios, mercury, arsenic, antimony, silver, molybdenum, thorium, uranium, rare earth elements. Radiometric methods (the carbon bomb pulse of (14)C, (210)Pb and conventional (14)C dating) are combined to allow reliable age-depth models to be reconstructed for each peat profile.     

The organic composition of diesel particulate matter, diesel fuel and engine oil of a non-road diesel generator

Diesel-powered equipment is known to emit significant quantities of fine particulate matter to the atmosphere. Numerous organic compounds can be adsorbed onto the surfaces of these inhalable particles, among which polycyclic aromatic hydrocarbons (PAHs) are considered potential occupational carcinogens. Guidelines have been established by various agencies regarding diesel emissions and various control technologies are under development. The purpose of this study is to identify, quantify and compare the organic compounds in diesel particulate matter (DPM) with the diesel fuel and engine oil used in a non-road diesel generator. Approximately 90 organic compounds were quantified (with molecular weight ranging from 120 to 350), which include alkanes, PAHs, alkylated PAHs, alkylbenzenes and alkanoic acids. The low sulfur diesel fuel contains 61% alkanes and 7.1% of PAHs. The identifiable portion of the engine oil contains mainly the alkanoic and benzoic acids. The composition of DPM suggests that they may be originated from unburned diesel fuel, engine oil evaporation and combustion generated products. Compared with diesel fuel, DPM contains fewer fractions of alkanes and more PAH compounds, with the shift toward higher molecular weight ones. The enrichment of compounds with higher molecular weight in DPM may be combustion related (pyrogenic).     

Response of the Ascorbate-Peroxidase of Selenastrum capricornutum to Copper and Lead in Stormwaters

The green alga Selenastrum capricornutum expresses a uniqueascorbate peroxidase, that responds to copper and lead. Attemptswere made to test if this peroxidase could be used to monitor thelevels of copper and lead in natural waters. When S.capricornutum was exposed to a stormwater sample, the specificactivity of the peroxidase in the cell extract was commensuratewith the combined copper and lead contents in the sample. Theperoxidase responses were also correlated with the 96 hr biomasstoxicity assay of S. capricornutum. However, unlike thebiomass toxicity assay, the peroxidase activity was not affectedby the anions in the samples. The use of this peroxidase can beused as a marker for testing heavy metal toxicity in the water.