Mo-N-TiO_2光催化剂的制备、表征及其活性提高机制

以钼酸铵和氨水分别为钼源和氮源,采用溶胶-凝胶法制备了Mo-N-TiO2光催化剂,并对其进行了XRD、XPS和UV-visDRS表征。XRD结果表明,Mo、N共掺杂有效抑制了TiO2晶粒的生长,提高了TiO2由锐钛矿向金红石相的转变温度。UV-vis表明,Mo-N-TiO2光催化剂可见光吸收能力增强,吸收带边明显＂红移＂,且钼酸铵添加量（相对TiO2）为0.5%的样品＂红移＂程度最大,最大吸收带边为550 nm。XPS分析结果表明,Mo取代了TiO2晶格中的部分Ti4＋,以Mo6＋形式存在的,而N以Ti—N及N—Ti—O形式存在。以罗丹明B为模型污染物,重点考察了钼酸铵添加量与焙烧温度对Mo-N-TiO2光催剂性能的影响。结果表明,400℃焙烧下、钼酸铵添加量为0.5%的样品催化活性最好。模拟太阳光下光照120min对罗丹明B的降解率达到96.8%,是纯TiO2的2.42倍。     

Carbonyl emissions from vehicular exhausts sources in Hong Kong

Vehicular emission (VE) is one of the important anthropogenic sources for airborne carbonyls in urban area. Six types of VE-dominated samples were collected at representative locations in Hong Kong where polluted by a particular fueled type of vehicles, including (i) a gas refilling taxis station (liquefied petroleum gas [LPG] emission); (ii) a light-duty passenger car park (gasoline emission); (iii) a minibus station (diesel emission); (iv) a single-deck-bus depot (diesel emission); (v) a double-deck-bus depot (diesel emission); and (vi) a whole-food market entrance for light- and heavy-duty vehicles (diesel emission). A total of 15 carbonyls in the samples were quantified. Formaldehyde was the most abundant carbonyl among the VE-dominated samples, and its contribution to the total quantified amount on a molar basis ranged from 54.8% to 60.8%. Acetaldehyde and acetone were the next two abundant carbonyls. The carbonyls were quantified at three roadside locations in Hong Kong. The highest concentrations of formaldehyde and acetaldehyde, 22.7 +/- 8.4 and 6.0 +/- 2.8 microg/m3, respectively, were determined in the samples collected at a main transportation gate for goods between Hong Kong and Mainland China. The total quantified carbonyl concentration, 37.9 +/- 9.3 microg/m3, was the highest at an entrance of a cross-harbor tunnel in downtown area. The theoretical carbonyls compositions of the three roadside locations were estimated according to the VE-dominated sample profiles and the statistics on vehicle numbers and types during the sampling period. The measured compositions of formaldehyde were much higher than the theoretical compositions in summer, demonstrating that photochemical reactions significantly contributed to the formaldehyde production in the roadsides.     

植物对潜流人工湿地净化微污染水效果的影响研究

以4种湿地植物为实验对象,在野外构建中试潜流人工湿地,研究了不同植物及植物连根收割对湿地运行效果的影响。结果显示,植物明显提升了湿地的去污效果;其中美人蕉湿地的TP和NH4+-N去除率最高,达到55.6%和78%;空心菜湿地的TN去除率最高,达到80.5%;芦竹湿地的COD去除率最高,为26.6%;植物连根收割后,湿地运行效果下降;其中TN去除率降至空白水平之下,而其他污染指标下降至略高于空白的水平。     

无砾石微孔管地下渗滤系统处理生活污水的中试研究

进行了无砾石微孔管地下渗滤系统处理生活污水的中试研究。基于不同土壤、不同管径、不同植物的协同效应,对比研究了不同系统处理污水中有机物、氮、磷和SS的去除效果及其影响因素。结果表明,不同土壤、不同管径及不同植物组成的系统,对生活污水中有机物、氮、磷和SS的去除效果差别较大。中试系统对COD、总磷、氨氮、总氮和SS的最佳去除率分别达到86.13%、90.20%、61.24%、65.49%和97.43%,对应的出水COD、总磷、氨氮、总氮和SS的平均浓度分别为64.29、0.69、22.13、26.19和5.56 mg/L。分析表明,进水SS浓度过高、外界温度下降等共同作用是导致系统对生活污水中NH4+-N和TN的去除率相对较低的主要原因。     

高分子量高纯度阳离子聚丙烯酰胺的合成

以丙烯酰胺与丙烯酰氧乙基三甲基氯化铵为单体,在复合引发剂的作用下,选择水溶液共聚法合成高分子量与高纯度阳离子型聚丙烯酰胺(CPAM)。实验表明,有机偶氮引发剂A用量0.5‰、氧化还原引发剂用量0.45‰、还原剂与氧化剂摩尔比2∶1、反应体系pH为4与反应时间5 h条件下,CPAM分子量为1 042万,且溶解性好。通过对聚合物残单含量影响因素添加剂用量、反应时间的研究,结果表明,添加剂EDTA和增溶剂D对残留AM含量影响小,而苯甲酸钠对聚合物残留AM的含量影响显著;延长反应时间至7 h,残单含量可降低至0.27%,CPAM的纯度高。通过与国内外3种同类型产品进行对比,结果表明,自制产品的分子量明显高于其他产品,且残单含量比国内产品降低了50%～75%。     

曝气浸没固定生物膜反应器处理化粪池出水

研究了以丝瓜络作为生物膜载体的曝气浸没固定生物膜反应器在处理化粪池出水时的可行性以及运行性能。结果表明,丝瓜络生物膜反应器可以在2周内成功启动;水力停留时间(HRT)对COD和氨氮的去除效果有显著影响,在水力停留时间为4 h的条件下,系统对COD和氨氮的去除率分别达到了78.5%和96.4%。另外,系统有较强抗有机污染物冲击负荷的能力,当COD和氨氮的进水浓度分别为59.3 mg/L和15.9 mg/L时,系统对有机污染物的去除效果较佳,去除率分别达到了80.0%和98.9%。     

Mo-N-TiO2光催化剂的制备、表征及其活性提高机制

以钼酸铵和氨水分别为钼源和氮源,采用溶胶-凝胶法制备了Mo-N-TiO2光催化剂,并对其进行了XRD、XPS和UV-visDRS表征。XRD结果表明,Mo、N共掺杂有效抑制了TiO2晶粒的生长,提高了TiO2由锐钛矿向金红石相的转变温度。UV-vis表明,Mo-N-TiO2光催化剂可见光吸收能力增强,吸收带边明显"红移",且钼酸铵添加量(相对TiO2)为0.5%的样品"红移"程度最大,最大吸收带边为550 nm。XPS分析结果表明,Mo取代了TiO2晶格中的部分Ti4+,以Mo6+形式存在的,而N以Ti—N及N—Ti—O形式存在。以罗丹明B为模型污染物,重点考察了钼酸铵添加量与焙烧温度对Mo-N-TiO2光催剂性能的影响。结果表明,400℃焙烧下、钼酸铵添加量为0.5%的样品催化活性最好。模拟太阳光下光照120min对罗丹明B的降解率达到96.8%,是纯TiO2的2.42倍。     

晚期垃圾渗滤液的部分亚硝化

利用实验室小试SBR在(33±1)℃的条件下,通过动态调控溶氧浓度(DO)(2～7 mg/L)和水力停留时间(2～5 d),经过130 d的运行成功启动了晚期垃圾渗滤液(NH4+-N含量1 227～2 133 mg/L)的部分亚硝化,使出水NO2--N∶NH4+-N稳定维持在1∶1左右,为后续的厌氧氨氧化工艺创造了进水条件。利用实时荧光定量PCR研究启动过程中的特异微生物氨氧化细菌的含量变化表明,氨氧化细菌的含量与NO2--N的生成速率和出水NO2--N稳定性有着显著相关性。     

利用二维表对活性污泥工艺模拟时的流量进行平衡的方法

多点进水和多重回流成为提高活性污泥工艺去除污染物能力的常用方法,这导致活性污泥工艺流程较为复杂。对工艺进行模拟计算时,由于模拟池体数量比实际池体数量更多,流量平衡较为困难。根据工艺流程特征提出了主流线、副流线等概念,结合流量分配比、循环流量等参数,利用二维表进行流量平衡计算,简捷明了,便于检验,大大提高了进行流量平衡的准确性和效率。     

Characterization of the extracellular biodemulsifiers secreted by Bacillus cereus LH-6 and the enhancement of demulsifying efficiency by optimizing the cultivation conditions

A highly efficient demulsifying strain, LH-6, was isolated from petroleum-contaminated soil and identified as Bacillus cereus by 16S rDNA gene analysis. It achieved 95.61 and 95.40 % demulsifying ratios within 12 h for water-in-oil (W/O) and oil-in-water (O/W) model emulsions, respectively. Fourier transform infrared spectroscopy (FT-IR) and thin-layer chromatography (TLC) detections indicated that the LH-6’s extracellular biodemulsifiers were different types of lipopeptides for the W/O and O/W emulsions. Optimization of the culture medium composition was conducted to improve the biosynthesis and demulsifying efficiency of the biodemulsifier. The optimal carbon source was liquid paraffin, while waste frying oil could also be an alternative carbon source. The optimal nitrogen sources were ammonium sulfate and yeast extract. To further enhance the biodemulsifier efficiency, the optimal cultivation conditions were determined using response surface methodology (RSM) based on central composite rotation design (CCRD). Using the optimized cultivation conditions, the demulsifying ratios increased to 98.23 and 97.65 % for the W/O and O/W model emulsions, respectively.